Question about 2003 Nissan Xterra

Open Question

How do you replace crank sensor on 2003 nissan xterra 3.3L

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: nissan xterra knock sensor

It's the valley of the engine underneath the intake manifold. It's about an $800 job because the top of the engine has to come off. However, unless you have a supercharged xterra it shouldn't effect performance. Also, the knock sensor will not trip the check engine light, as it does not indicate a primary problem, so if your light is on you should have another code that should be fixed first.

Posted on Nov 24, 2008

Ad
  • 1 Answer

SOURCE: knock sensor

You have to take the entire intake manifold off upper and lower. you will find it on the main block after you take the lower manifold off.

Posted on Jun 03, 2009

HyeProfile
  • 35 Answers

SOURCE: Trying to replace the knock sensor in my 2000

From the service manual:457bed1.png

Posted on Aug 05, 2009

ZJLimited
  • 17970 Answers

SOURCE: Diagram available for 01 Nissan Xterra Knock Sensor location?

V6 3.3L The sensor is located underneath the air intake manifold on top of the engine block. This should take an experienced mechanic about 3-4 hours to replace.

9bd8ec7.jpg

Fig. Engine compartment component locations

Hope this help (remember rated this free help) Good luck.

Posted on Feb 08, 2010

SOURCE: HOW TO REPLACE A FUEL PUMP FOR A NISSAN XTERRA


Removal & Installation

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Relieve the fuel system pressure.
  3. Drain the fuel tank.
  4. Remove or disconnect the following:

    Negative battery cable Fuel pump module harness connectors Filler hose shield Fuel pressure and return lines Filler hose Vent hose Evaporative Emissions (EVAP) hose Fuel tank skid plate Fuel tank Fuel level sender Fuel pump

To install:
  1. Install or connect the following:

    Fuel pump Fuel level sender. Tighten the screws to 17-23 inch lbs. (2.0-2.5 Nm). Fuel tank. Tighten the bolts to 27-36 ft. lbs. (37-49 Nm). Fuel tank skid plate. Tighten the bolts to 27-36 ft. lbs. (37-49 Nm). EVAP hose Vent hose Filler hose Fuel pressure and return lines Filler hose shield Fuel pump module harness connectors Negative battery cable
  2. Fill the fuel tank.
  3. Start the engine and check for leaks.

Posted on Mar 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crash sensor located in a nissan xterra 2003


There are several crash sensors for that vehicle. Which one are you looking for?

Feb 19, 2015 | 2003 Nissan Xterra

1 Answer

How is the best way to get to get the crank postion sensor on 03 nissan xterra 3.3motor


I am sending you a link and there are 3 pictures. Click on the middle one or the far right if you recognize your engine you will notice that CPS is on the right rear of the engine good luck. http://www.2carpros.com/questions/2003-nissan-xterra-ive-been-looking-crankshaft-sensor-find-you-send-picture-tha. Click on this and then click on it again to open.

Jan 25, 2015 | Nissan Cars & Trucks

1 Answer

How dificult is it to replace a Knock sensor on a 2003 Nissan Xtera 3.3l?


so easy takes only 3.9 hrs it under the intake be sure to not over tighten the bolts not too tight at all

Jul 11, 2014 | 2003 Nissan Xterra

2 Answers

Picture/location of crankshaft position sensor 2003 nissan exterra


The location is in back of the engine on the top of the transmission3_17_2012_9_03_53_pm.jpg

Mar 17, 2012 | 2003 Nissan Xterra

2 Answers

Cranks but won`t start will start with starting fliud for a few


fuel problem then .either a plugged fuel filter or the fuel pump is not working .. if you were to shoot a little fuel into the throat of the throttle body or air cleaner area you say it will run .? if so you are not getting fuel up to there . sounds like maybe a possable pump . always replace cheapest thing first like filter .. thanks Jerry holler if you need more.

Jan 30, 2009 | 2003 Nissan Xterra

Not finding what you are looking for?
2003 Nissan Xterra Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...