Question about Cars & Trucks

Open Question

Removing cv joint from a holden colorado - Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chiquititas
  • 1010 Answers

SOURCE: removal of cv joint

Go to a mechanic, safe way...

Posted on Jun 22, 2008

  • 6982 Answers

SOURCE: 1998 grand cherakee driver side cv joint removal

You can find instructions for doing this in any half decent manual. One thing they usually don't tell you is when removing the large axle nut on the end, it helps to put a spare tire on with no center cap and with the vehicle on the ground, break that nut free before starting the job. without air tools, it's next to impossible to remove it when jacked up.

Posted on Mar 10, 2009

cadman000
  • 607 Answers

SOURCE: cv boot clamp came off somehow from the outer hub assembly

athere is a snap ring within the CV joint the nedds to be spread OPEN to release CV joint from axle, Once CV is cleaned and repacked with grease rintall onto axle by again spreading apart clamp. Prior to installing CV joint slide NEW CV joint boot onto axle, Cleanly intall add'l grrease and reinstall CV boot.

Posted on Apr 04, 2009

yotaguy
  • 232 Answers

SOURCE: replacing CV Joints

Yes you can remove the drive shaft by unbolting the bottom ball joint,then removing the nut that holds the shaft in the hub I would'nt recommend trying to replace just the CV joint as this can be a very complicated procedure involving specialized tools and more than just general mechanical skill,this isn't true of all,as some CV's come apart fairly easily.If the joint is bad you should probably just replace the axle.Remember to match mark any adjustable parts you may have to disassemble,and when you reassemble make sure to check the splines of the shaft and the drive hub,remove any foreign material and carefully file or sand any burs or scratches,any of these can cause the spline to bind on reassembly and possibly cause irreparable damage to one or both parts.Good luck hope this helps.

Posted on Apr 10, 2009

  • 416 Answers

SOURCE: when replacing a outer C.V joint boot , do you

you can replace just the outter but you may want to replace the whole axle alot easier

Posted on Jan 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 Holden Colorado wont Start don't have dash lights and have a good battery


How about head lights ? If no clean battery cable ends check other end for connections

Jul 11, 2016 | Holden Cars & Trucks

1 Answer

My 2005 holden cruze has started to make a clicking noise when in low gear. I don't seem to hear it in higher gears and it it doesn't make it in reverse..


the clicking noise especially on slow turns indicates that the cv joints need replacing
have it checked out by an accredited transmission or drive line shop

Oct 13, 2015 | Holden Cars & Trucks

1 Answer

Ts Holden Astra how do I tell if it's my gearbox


what are the symptoms ? usually only way is to strip down the drive shafts and manually twist and turn the cv joint and see/hear if it turns freely and has sufficient grease etc

Oct 18, 2014 | Cars & Trucks

1 Answer

Removing a drivers side cv joint on a 95 holden rodeo?


You have to remove the wheel then take the brake caliper off remove the nut from the upper control arm drop it down using a tye rod remover take nut off cv joint then use a pry bar to pop the cv joint from transmission now pull out of axle and remove.

Nov 29, 2010 | Isuzu Rodeo Cars & Trucks

2 Answers

Cv joint but the plastic thang that go around it


One would have to remove the half shaft to service the cv joint properly.

CV-Joints Overhaul Check the CV-boot for wear tccs7030.jpg

Removing the outer band from the CV-boot tccs7031.jpg

Removing the inner band from the CV-boot tccs7032.jpg

Removing the CV-boot from the joint housing tccs7033.jpg

Clean the CV-joint housing prior to removing boot tccs7034.jpg

Removing the CV-joint housing assembly tccs7035.jpg

Removing the CV-joint tccs7036.jpg

Inspecting the CV-joint housing tccs7037.jpg

Removing the CV-joint outer snapring tccs7038.jpg

Checking the CV-joint snapring for wear tccs7039.jpg

CV-joint snapring (typical) tccs7040.jpg

Removing the CV-joint assembly tccs7041.jpg

Removing the CV-joint inner snapring tccs7042.jpg

Installing the CV-joint assembly (typical) tccs7043.jpg

prev.gif next.gif

Oct 08, 2010 | 2004 Oldsmobile Alero

1 Answer

How do I get the cv joint seperated from the shaft of the axel because i need to do that to place a new cv boot on?


To replace the outer boot on this shaft you have to first remove the inner joint from the shaft, then remove the outer joint boot from the shaft and joint by sliding it back down the shaft. Do not remove the outer CV joint from the shaft. I believe you have to replace the entire axle shaft if it is removed as it's not made to be removed and reinstalled. I would actually suggest replacement of the entire shaft instead of just the boot anyway unless you were lucky enough to catch a leaking boot as soon as the boot went bad as it takes such a very small amount of road grit to start the damage that will eventuall wear out the joint and then you have to take the axle out again. [just my opinion as over the years I've seen dozens of bad boots cause joints to fail a short time later] Hope this helps out a bit and good luck!

Jun 25, 2010 | 2005 Chevrolet Colorado

2 Answers

I have a 2004 Chevy Colorado and can not get the hub off to change out my front rotors.


Very, very few cars or trucks require the hub to be removed. In almost all American vehicles, the rotors are just resting on the hub and will come off fairly easily. Make sure you've removed the caliper, then smack the rotors a bit with a rubber mallet. They should come off. If there's a ton of rust, you might need to use some penetrating oil, then smack them a little.

Sep 01, 2009 | 2004 Chevrolet Colorado

1 Answer

02yukon i cannot get the cv joint out from the wheel/brake assem


Remove steering joint.Then bottom ball joint then you should be ok.

Jul 13, 2009 | 2001 GMC Yukon

1 Answer

Colorado issues


if it make that sound when you turn left its your CV joint

May 19, 2009 | 2006 Chevrolet Colorado

1 Answer

Cv boot clamp came off somehow from the outer hub assembly


athere is a snap ring within the CV joint the nedds to be spread OPEN to release CV joint from axle, Once CV is cleaned and repacked with grease rintall onto axle by again spreading apart clamp. Prior to installing CV joint slide NEW CV joint boot onto axle, Cleanly intall add'l grrease and reinstall CV boot.

Apr 04, 2009 | 1996 Buick Century

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...