Question about Cars & Trucks

Open Question

2003 pontiac grand am code p0341 changed camshaft sensor and pigtail. No help.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
davesmith_37
  • 94 Answers

SOURCE: P0340 Code Camshaft Position Sensor


The Camshaft Position (CMP) Sensor detects the position of the camshaft in order to identifiy when piston No. 1 is on its compression stroke. The CMP sensor is used for ignition timing in the Ford DIS igntion system, but not in the EDIS igntion system. Both DIS/EDIS use the CMP signal for synchronizing the firing of sequential fuel injectors.

On the 3.0L vulcan engine, the CMP signal is generated by a single Hall-Effect magnetic switch, activated by a single "vane" spinning around by virture of a synchronized shaft which is driven by the camshaft. 

The CMP sensor & synchronizer/shaft are located behind the intake manifold (i.e., back near the firewall on a Ranger) on the top of the cylinder block. If you just need to replace the sensor, it is a simple job of unplugging the electrical connector and removing the screws holding the sensor in place. Here is a sketch of the sensor to give you an idea what to look for:

Posted on Feb 27, 2009

Ad
  • 55 Answers

SOURCE: replacing bad camshaft position sensor

  1. Disconnect battery ground cable.
  2. Remove water pump pulley attaching bolts, then the serpentine belt and water pump pulley.
  3. Disconnect sensor wiring connector and remove sensor retaining bolt.
  4. Twist and pull sensor to remove.
Reverse procedure to install and prior to installing new sensor, lubricate sensor O-ring.

It is located under the water pump. Make sure when you remove the sensor that you rotate the crank shaft and look in the hole to make sure the pick up magnet is still in there. Sometimes they come loose and cause a no start or long crank. You will need to have the code cleared still.

Posted on May 06, 2009

outdoorsman5
  • 631 Answers

SOURCE: Where Is The Camshaft Position Sensor Located On

Front of engine above crankshaft pulley. If you need a picture of it send me your email address and I will send you a picture.

Posted on Sep 10, 2009

Testimonial: "Thank you soooo much you hit the nail on the head without asking a million questions that don't pertain to what I need to know. You know your stuff!!!"

wracefans24
  • 1985 Answers

SOURCE: what do codes p0335 and p0341 mean on 1996 Cavalier?

when your engine went into that 5 second sputter,
your computer or "PCM" did not get a constant signal from the crank or cam sensors that the engine was running.
These two sensors tell the computer what RPM the engine is turning so it can adjust fuel and spark.

Posted on Nov 21, 2009

  • 14036 Answers

SOURCE: how do you change the camshaft position sensor on

YOU HAVE TO REMOVE DRIVE BELT.YOU HAVE TO REMOVE POWER STEERING PUMP SET IT ASIDE DONT DISCONNECT ANY LINES.NOW YOU CAN DISCONNECT CMP SENSOR ELECTRICAL CONNECTOR THEN REMOVE THE CMP SENSOR.

Posted on Aug 30, 2010

Testimonial: "TX. I was quoted $580 by the dealer to do this job and the online price of the part is less than $50"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

06 Pontiac G6 2.4 I replaced the motor, started right up and ran great. Shut it off, now it won't start. I have no spark, and codes, po366 and po341 showed up. What's common to these 2 sensors?


DTC P0340: Intake CMP Sensor Circuit
DTC P0341: Intake Camshaft Position (CMP) Sensor Performance
DTC P0365: Exhaust Camshaft Position (CMP) Sensor Circuit
DTC P0366: Exhaust Camshaft Position (CMP) Sensor Performance

The five volt reference circuit .

The 4X camshaft position (CMP) sensor circuits consist of an engine control module (ECM) supplied 5-volt reference circuit, low reference circuit, and an output signal circuit. The CMP sensor is an internally magnetic biased digital output integrated circuit sensing device. The sensor detects magnetic flux changes of the teeth and slots of a 4-tooth reluctor wheel attached to the camshaft. As each reluctor wheel tooth rotates past the CMP sensor, the resulting change in the magnetic field is used by the sensor electronics to produce a digital output pulse. The sensor returns a digital ON/OFF DC voltage pulse of varying frequency, with 4 varying width output pulses per camshaft revolution that represent an image of the camshaft reluctor wheel. The frequency of the CMP sensor output depends on the velocity of the camshaft. The ECM decodes the narrow and wide tooth pattern to identify camshaft position. This information is then used to determine the optimum ignition and injection points of the engine. The ECM also uses CMP sensor output information to determine the camshaft relative position to the crankshaft, to control camshaft phasing, and for limp-home operation.
Do you know what the five volt reference circuit is .

How to check the 5v reference circuit for short to ground Cadillac

Mar 17, 2017 | Pontiac Cars & Trucks

1 Answer

I own a 1998 Chevy Lumina, took it to Advance Auto. I know what one code is what does code P0341 mean and how can it be fixed?


Hi, Im AL the owner of Big As Auto Repair.

P0341 is a code for Camshaft Position Sensor Circuit. The first thing you need to do sense its a circuit code, is to change the Camshaft Position Sensor. I don't know what engine you have, but if its the 3.4 engine the sensor will be directly under the Power Steering Pump. Remove the pump and replace the sensor, clear the codes and hopefully the sensor does the fix. If not it could be in the wiring or engine controller. Hope this helps and please visit my auto-repair-website and give me a thumbs up. http://www.bigasautorepair.com/

Jan 24, 2016 | Cars & Trucks

2 Answers

Po341 code cts


Camshaft position sensor A circuit range /performance bank 1 or single sensor

Mar 06, 2014 | 2003 Cadillac CTS

1 Answer

Misfire p0341 nissan armada


Error Code: P0341
Description:
Camshaft Position (CMP) Sensor A, Bank 1 - Implausible Signal
Indication:
Malfunction Indicator Lamp (MIL) active.
Possible Causes:
Wiring from/to Camshaft Position Sensor (CMP) faulty.
Camshaft position (CMP) sensor faulty.
Timing misaligned.

Mar 05, 2014 | 2004 Nissan Armada

1 Answer

Tiburon ignition


Did you check to see if the timing belt is turning the camshaft?

Sep 08, 2013 | Cars & Trucks

1 Answer

2002 isuzu rodeo 2.2 liter code P0341 cmp range or performance problems


P0341 ISUZU - Camshaft Position Sensor Performance
Possible causes- Faulty Camshaft Position Sensor
- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery

Sep 10, 2012 | 2002 Isuzu Rodeo

2 Answers

93 Bonneville with code 41 (p0341).


If car starts and shuts down check out the VAT system - may have to be reset.

Aug 31, 2017 | 1993 Pontiac Bonneville

2 Answers

How to replace the camshaft sensor in a 1998 pontiac grand am gt


YOU MUST REMOVE POWER STEERING PUMP, AND BELT THE SENSOR IS UNDER THE PUMP IN THE BLOCK.

Dec 19, 2010 | 1998 Pontiac Grand Am

1 Answer

Stalling,check engine light cam shaft sensor position A code


the code for camshaft sensor is--p0341 and p0342, po341 is camshaft range or performance problem. p0342 is camshaft curcuit , low input. hope this helps carl.

Jul 28, 2009 | 2004 Dodge Intrepid

1 Answer

2005 dodge diesel codes!


Hi..
the Code P0340, Camshaft Position sensor problem or Loss signal.
The Code P0341, Camshaft Position sensor Intermitent Signal.

The First step you should do is : Locate the Camsahaft sensor,
Is located On Right Front of the Engine..
It use a 3 wires Connector.
1-- Pink/Yellow
2-- Brown/Orange
3-- Dark blue/Gray.

After you found it. Inspect the Connector. If is The connector in good condition.
Replace the Camshaft Position sensor...

Ok... I hope this help on your problem..
Thank you for use Fixya...

Sep 27, 2008 | 2005 Dodge Ram

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...