Question about Nissan Xterra

Open Question

Location of crank sensor on 2003 Nissan Xterra 3.3L

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: nissan xterra knock sensor

It's the valley of the engine underneath the intake manifold. It's about an $800 job because the top of the engine has to come off. However, unless you have a supercharged xterra it shouldn't effect performance. Also, the knock sensor will not trip the check engine light, as it does not indicate a primary problem, so if your light is on you should have another code that should be fixed first.

Posted on Nov 24, 2008

Ad
alicantecoli
  • 22246 Answers

SOURCE: crank sensor location on Hyundai Sonata 2003 model

look carefully on bellhousing and rocker cover/head it has to be somewhere

Posted on Apr 03, 2009

localwonder
  • 6784 Answers

SOURCE: crank angle sensor location

The crank sensor is always located next to the crankshaft pulley. it will be inserted into the block with the top part of the housing half way out. you cant miss the wires leading into the tip of the housing next to the crank shaft pulley.

Posted on May 23, 2009

  • 8 Answers

SOURCE: P0335 CRANK POSITION SENSOR A CIRCUIT MALFUNTION

crank sensors are usually located in/near the distributor.

Posted on Jun 07, 2009

c17hydro
  • 2984 Answers

SOURCE: high idle stalls at lights code for crank sensor

Crankshaft and Camshaft Position Sensors Camshaft Position Sensor Engine timing is determined from the relationship between the crankshaft and camshaft. This relationship is maintained by a timing chain or timing belt. The Engine Management System does not control engine timing but it does monitor the relative position and speed of these shafts by monitoring signals generated by sensors. The Engine Management System (EMS) uses signals generated by the camshaft position sensor to synchronize fuel injection to the valve sequence and for the on-board diagnostic procedure for misfire detection. The EMS energizes the injector at or near the time the intake valve opens. For misfire diagnosis, the EMS compares the number of camshaft sensor reference pulses and the number of crankshaft position sensor reference pulses received. If the EMS receives an incorrect number of pulses Diagnostic Trouble Codes (DTC’s) should be stored in the EMS.
If the camshaft position sensor or circuit is faulty most engines will start. Some engine management systems will then default to a pre-programmed injector firing sequence. All injectors may be energized simultaneously or all of the injectors on one bank may be energized at the same time. If the CMP data is required for misfire detection and reliable CMP data is not present misfire detection would probably be suspended.
Related Symptoms The following symptoms can be caused by an intermittent wiring connection or faulty signal to the EMS:

  • Extended crank time with a cold engine
  • Intermittent rough running
  • Unstable idle
  • Bucking
  • Hesitation
  • Stumble
  • Chuggle
  • Poor fuel economy
  • Stalling on acceleration
Crankshaft Position Sensor Engine speed is a very important input to the Engine Management System (EMS). Crankshaft speed and position are the basis for many calculations made by the computer. Crankshaft position values are transmitted to the computer by pickup coils also known as Permanent Magnet (P/M) generators, hall-effect sensors or optical sensors. The Crankshaft Position Sensor (CKP) also known as engine speed sensor is located in close proximity to the crankshaft.
In addition the EMS uses minute variations in the CKP sensor data to determine engine misfire. The EMS uses this information in conjunction with the camshaft position sensor to perform misfire diagnostics.
Related Symptoms: No Start/Intermittent Start Condition – Can be caused by a faulty crankshaft position sensor due to loose connections, bad grounds, high resistance in the circuit, or opens in the circuit

Posted on Jun 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crash sensor located in a nissan xterra 2003


There are several crash sensors for that vehicle. Which one are you looking for?

Feb 19, 2015 | 2003 Nissan Xterra

1 Answer

How is the best way to get to get the crank postion sensor on 03 nissan xterra 3.3motor


I am sending you a link and there are 3 pictures. Click on the middle one or the far right if you recognize your engine you will notice that CPS is on the right rear of the engine good luck. http://www.2carpros.com/questions/2003-nissan-xterra-ive-been-looking-crankshaft-sensor-find-you-send-picture-tha. Click on this and then click on it again to open.

Jan 25, 2015 | Nissan Cars & Trucks

2 Answers

Picture/location of crankshaft position sensor 2003 nissan exterra


The location is in back of the engine on the top of the transmission3_17_2012_9_03_53_pm.jpg

Mar 17, 2012 | 2003 Nissan Xterra

1 Answer

My car is cranking but no start,no spark. Where is the location of crankshaft position sensor on 2006 nissan Xterra?


go to your dealer parts and service if you don,t have a auto manual your make and model.the part man can look it up quicker.talk to the mechanic these nissan mechanics really great.and can save you time and money.

Jan 29, 2011 | 2006 Nissan Xterra

3 Answers

Diagram available for 01 Nissan Xterra Knock Sensor location?


V6 3.3L The sensor is located underneath the air intake manifold on top of the engine block. This should take an experienced mechanic about 3-4 hours to replace.

9bd8ec7.jpg

Fig. Engine compartment component locations

Hope this help (remember rated this free help) Good luck.

Feb 08, 2010 | 2001 Nissan Xterra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...