Question about 2003 Mercedes-Benz E-Class

Open Question

Esp light,bas light,abs light dtc c1611 - 2003 Mercedes-Benz E-Class

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ilragatzzo78
  • 241 Answers

SOURCE: BAS ASR problem

ok, first you have to clear the codes.
in this type of cars you cannot clear codes with a regular obd II it has to be the factory scanner or similar. after you clear the codes drive it for a while. when light comes back on scan it again and that is going to be your true problem. if you replaced the switch but didn't clear the code the light will be still on because the computer doesn't know that you fixed the problem. so try it out and let me know if worked.

Posted on May 15, 2008

Benimur
  • 6966 Answers

SOURCE: Warning Light on Mercedes ML270

Hi,

To my understanding:
BAS ESP - Electronic Stability Program (keeps you moving in the direction you intended the vehicle to go); probably a faulty brake switch or a bad brake sensor. You may want to reference this forum for additional insights;
ETS - Electronic Traction System (keeps you moving); would require an appropriate code reader to diagnose and pinpoint problem.Surprisingly, there has been some reports of defective brake pedal switch that activates this warning. You may lilkewise want to reference this forum for additional insights.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

Posted on Jun 06, 2008

mercanic
  • 14 Answers

SOURCE: mercedes benz bas/esp light on

Change the brake light switch first, its on the brake pedal, £9 from mercedes.
jib
www.mercanic.co.uk

Posted on Nov 24, 2008

  • 1 Answer

SOURCE: A class mercedes 160 BAS ESP light came on after a

orange esp light comes on every so often

Posted on Dec 13, 2009

merctechniqu
  • 229 Answers

SOURCE: mercedes benz bas.esp light on when driving

check brake light switch and replace it, it's most common fault. is this information helped you. please vote me and leave a comment.

Posted on Oct 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bas/esp light is on inmy jeep commander 2006


This video is for a liberty, but all Jeeps should be similiar.
Jeep Liberty How to fix Traction ABS EST Light Codes C1240 C123F Also a guy in a forum says that it might involve a recall of the DCX recall applying to ABS modules on many Chrysler, Dodge, & Jeep products including the Commander. I'd call your dealer and ask, they might fix it for free if it's a recall. http://www.jeepcommander.com/forums/5-general-commander-discussion/1483-esp-bas-traction-control-light-staying.html

Nov 17, 2016 | Jeep Cars & Trucks

1 Answer

The esp bas, abs, traction & brake light come on when I drive


take it to a mechanic! the drive train is failing

Jun 09, 2015 | 2008 Dodge Grand Caravan

1 Answer

My esp/bas light stays on


the operators manual is clear on that, did you read that first?
it says "get the car serviced" clearly
if you work on cars, do you? thne we scan the systems with the scan tool first. to see if there are complex hard errors.
like the ABS sensors, (not bas) sensor dead. (ops a road hazard hit it and broke the wire there, dang.
then if no hard failures.
first is not ESP (that be last dead last)
the first is , the brake must work perfect if not , the ABS can not
work correctly with bad brakes.
so check fuses.
scan ABS for errors
then do a full brake inspection, takes me 2 hours. but my guess,
youve never done brakes, right,, your self?
not even a full inspection?
  1. leaks? (fluid)
  2. pads worn out?
  3. caliper pistons not sticking
  4. rotors not cracked, or wrecked, surfaces.
  5. caliper guide pins not seized. (they float free?)
  6. emg, brake not sticking on partially?
  7. wrong sized tires on car (or just one , omg)
  8. ABS sensor parts damaged at axles ends.?
  9. bad wheel bearing, seizing or loose.
etc... etc.... and more.

Feb 05, 2015 | 2006 Jeep Grand Cherokee

1 Answer

Esp bas light abs


get the brakes serviced first.
neither of those work with bad brakes.
check fuses 1st.
then scan it, scan the ABS. see DTC codes,
if it says a sensor is dead. well it is..
each code has different meanings and further tests.
but we check that the brakes work.first.

imagine if you will, trying to fix cruise control with a dead engine.
see?

Jul 09, 2014 | 2007 Jeep Liberty Sport

1 Answer

My esp light has come on and it won't turn off on a Audi a3 2006


TDISLine 1874 solutions Jun 16, 2012
The ESP system means the Electronic Stability Program. If the ESP lights on the dashboard permanently the ESP system is faulty.
You should access the ESP Electronic Control Unit (ECU) memory for pull out all DTC (Diagnostic Trouble Codes), using diagnostic equipment connected to the data link connector of the car. Then you will be full informed about bad pieces (e.g.: brake pedal switch, front right wheel abs sensor interrupted, ...). After bad pieces replacement you will be able to erase all faults memored by ESP ECU, in other words reset the ESP system and turn off the warning lamp on dashboard.

Check & replace if necessary the brake pedal switch placed above pedals on the support.

If the problem still occurs you should access the ABS & ESP ECU (Electronic Control Unit) using diagnostic equipment connected to the data link connector of the car, in order to pull out all DTC (Diagnostic Trouble Codes) memored.
Then you will be able to replace bad piece(s) and fix the problem by erasing all DTC stocked inside ABS & ESP ECU, and reset it.

Jan 09, 2013 | Cars & Trucks

1 Answer

The ESP light on my AudiA3 stays on


The ESP system means the Electronic Stability Program. If the ESP lights on the dashboard permanently the ESP system is faulty.
You should access the ESP Electronic Control Unit (ECU) memory for pull out all DTC (Diagnostic Trouble Codes), using diagnostic equipment connected to the data link connector of the car. Then you will be full informed about bad pieces (e.g.: brake pedal switch, front right wheel abs sensor interrupted, ...). After bad pieces replacement you will be able to erase all faults memored by ESP ECU, in other words reset the ESP system and turn off the warning lamp on dashboard.

Check & replace if necessary the brake pedal switch placed above pedals on the support.

If the problem still occurs you should access the ABS & ESP ECU (Electronic Control Unit) using diagnostic equipment connected to the data link connector of the car, in order to pull out all DTC (Diagnostic Trouble Codes) memored.
Then you will be able to replace bad piece(s) and fix the problem by erasing all DTC stocked inside ABS & ESP ECU, and reset it.


tdisline_516.jpg

Jun 16, 2012 | 2006 Audi A3

1 Answer

What does ESP light mean on a cls 500 Mercedes Benz


The ESP system means the Electronic Stability Program. If the ESP lights on the dashboard permanently the ESP system is faulty.
You should access the ESP Electronic Control Unit (ECU) memory for pull out all DTC (Diagnostic Trouble Codes), using diagnostic equipment connected to the data link connector of the car. Then you will be full informed about bad pieces (e.g.: brake pedal switch, front right wheel abs sensor interrupted, ...). After bad pieces replacement you will be able to erase all faults memored by ESP ECU, in other words reset the ESP system and turn off the warning lamp on dashboard.

Check & replace if necessary the brake pedal switch placed above pedals on the support.

If the problem still occurs you should access the ABS & ESP ECU (Electronic Control Unit) using diagnostic equipment connected to the data link connector of the car, in order to pull out all DTC (Diagnostic Trouble Codes) memored.
Then you will be able to replace bad piece(s) and fix the problem by erasing all DTC stocked inside ABS & ESP ECU, and reset it.


tdisline_516.jpg

Feb 10, 2012 | 2006 Mercedes-Benz Mercedes Benz CLS500

Not finding what you are looking for?
2003 Mercedes-Benz E-Class Logo

Related Topics:

361 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75197 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...