Question about 2008 Cadillac Dts
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door
Posted on Aug 14, 2009
you should have to go thru under the hood to the backside of the lamp assembly. There should be either a hard plastic cap or a plastic dust cover that has the wires going thru it to the lights. If it is the hard cover (looks like a jar cap) turn it 1/4 turn counterclockwise and pull it out of the way. Take the bulb/socket out. Unclip the old one- Put the new one in. (DO NOT TOUCH THE GALSS PART OF NEW BULB). Then re-assemble
Posted on Mar 11, 2010
Actually no you don't. Crank your steering wheel all the way to the right so yo have the maxumum clearance for your hands and arms in the front of the wheel well. Remove the plastic clips that hold the wheel well splash guard and pull it back enough to allow access to the interior of your bumper.
Replace bulbs as needed.
Yes, a jack is nice and makes it a touch easier to access, but I did this in an AutoZone parking lot during a cross country road trip.
5 mins tops to complete.
Posted on Mar 14, 2010
Remove 3 or 4 of the plastic pins holding the inner fender. They are located around the lip of the fender opening. The pins are removed by pulling the center cap of the pin straight out about an 1/8" and then wiggle and pull the whole pin out.
Pull the inner fender down and back.
Reach your arm in and grab the socket and squeeze the locking tab.
Rotate the socket counter-clockwise less than a quarter turn, and pull straight back.
Reach your other hand in and remove the bulb by pulling it straight out of the socket. It takes a 3157 bulb
Posted on Jun 22, 2010
Testimonial: "Thank you so much for your help. Really I had ask the question about 3 months ago, but since I didn't had it fixed yet, it's OK now. Franco"
SOURCE: 2006 Cadillac CTS Turn Signal
The fender liner needs to be removed. It takes the removal of up to 20 plastic pins. Once it is out of the way the bulb sockets become available. twist the bulb socket counterclockwise and the bulb can be pulled out. Reverse order for reinstallation
Posted on Aug 01, 2010
Tips for a great answer:
Aug 29, 2016 | 2008 Cadillac Dts
Mar 01, 2016 | 2008 Cadillac Dts
Jun 13, 2015 | 2008 Cadillac Dts
Aug 01, 2014 | 2007 Cadillac DTS Sedan
May 28, 2014 | 2007 Cadillac DTS Sedan
Mar 04, 2013 | 2004 Cadillac SRX
Mar 26, 2012 | 2006 Cadillac SRX
Oct 30, 2011 | 2007 Cadillac DTS Sedan
Oct 30, 2011 | Cars & Trucks
32 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: