Question about Chevrolet Chevy

Open Question

Location of heater blend door on 2008 Chev HHR

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
duster292
  • 19 Answers

SOURCE: How can I locate the blend door for the heater/defroster

Well FOR THE FIRST PROBLEM YOU PROBABLY NEED TO REPLACE THE THERMOSTAT IT IS MORE THAN LIKELY CLOSED SHUT NOT LETTING COOLANT INTO THE BLOCK TO CIRCULATE THE HEATED COOLANT 2ND THE UNIT IN WHICH CONTROLS THE TEMPERATURE OF THE INSIDE OF THE VEHICLE IS OR MAY BE BAD I WOULD START WITH THE THERMOSTAT FIRST BEING THIS IS USUALLY A MORE COST AFFECTIVE SOLUTION GOOD LUCK!

Posted on Nov 21, 2008

Ad
  • 3 Answers

SOURCE: How to change heater blend doors on 2003 Jeep Grand Cherokee

go to wjjeeps.com there is several pictures and step by step instructions.

Posted on Dec 29, 2008

  • 74 Answers

SOURCE: 1997 jeep grand air blend door location

The Jeep Grand Cherokee sucks air from the outside via a hole on the passenger side of the cowl. It's under the black plastic piece that runs under the wipers.

The air is then sucked via the blower and blown into the housing where the heater core and A/C evaporator core live.

The blend door is inside this housing as well.

This also depends on if you have regular climate control or the more advanced ATC digital climate control found on some of the Limiteds.

You could possibly take out your glovebox and see if there are any broken pieces going to the door accuator.

Otherwise if it's internal, you'll need to take out the heater/ A/C housing.

To get to this housing, you have to take apart your entire dash, lift the top dash cover off, and then you'll see the housing. You could possibly check for a few thing there.

Most everything there is vacuum controlled.

You have to drain your antifreeze and have your A/C freon discharged (use a professional to capture the freon).

There are 5-6 nuts holding the housing to the firewall. You have to reach these from the engine compartment.

Disconnect your A/C lines and heater hoses. Pull out housing.

This is definately an advanced project, thus the reason for the high pricing.

Hopefully you can get it fixed without having to take this Jeep apart entirely. Try diagnosing with a vacuum gauge if necessary before tearing it apart.

Posted on Feb 10, 2009

  • 50 Answers

SOURCE: A/C and Heater Blend Door Actuator

location is on ac and heater box under dash.Good luck big jab to fix it.

Posted on Mar 13, 2009

bdubsee
  • 75 Answers

SOURCE: how to get to the headlight bulb chev 2008

You have to remove the plastic inner fender liner to access the rear of the headlamp assembly.
There is a great tutorial with photos at: http://chevyhhr.net/forums/showthread.php?t=5042&highlight=silverstar

Posted on Jan 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On 2008 chev hhr where is ECT coolant temp sensor ?


it is on the back of the engine between the heater core hoses.

Jul 05, 2015 | Cars & Trucks

1 Answer

Remove heater ac air posion moter on 2008 chev pickup


I think the part is called the blend door actuator.
1.You have to remove the plastic cover on passenger side. Motor is located over the transmission hump.
2. Remove wiring harness plug.
3. Remove 3 hex head screws.
You need a small 1/4 socket set.

Feb 22, 2015 | 2008 Chevrolet Silverado 1500 2WD

1 Answer

Where is the location on a 2005 Chev. Silverado blend door actuator


usually in the middle of the dash way back where you have to remove dash to get to it .

Feb 21, 2015 | 2005 Chevrolet Silverado

1 Answer

2008 mercury marquis blender door location


The blend-air door actuator on a 2008 Merury Grand Marquis is located on the top forward area of the HVAC housing under the instrument panel. Complete instrument panel removal is required to access it.

May 26, 2012 | 2008 Mercury Grand Marquis

1 Answer

Back door hhr chev. dont open fuse?


Yeah it has a fuse for all electrical functions.

Apr 10, 2012 | 2006 Chevrolet HHR

1 Answer

How to get to the headlight bulb chev 2008 hhr


You have to remove the plastic inner fender liner to access the rear of the headlamp assembly.
There is a great tutorial with photos at: http://chevyhhr.net/forums/showthread.php?t=5042&highlight=silverstar

Dec 26, 2009 | 2008 Chevrolet Hhr

2 Answers

Need 2 code rke system


Got to go to dealer. They use a Tech 2 scanner to communicate with the computer module.

Jul 20, 2008 | 2008 Chevrolet Hhr

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...