Question about 2007 Chevrolet Colorado (Extended Cab) New Cars

Open Question

2012 CHEV COLO, DIC SERV TPM & TIRE ICON COMES ON

TIRE ICON & DIC MSG SERV TPM, ALL 4 SENSOR REPLACED

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 518 Answers

SOURCE: A message on my dash came on say serv TPM...any

Tire pressure monitor. First check all tires for proper inflation. If 1 or more is low fill to proper psi. If all are correct need to plug into tire pressure monitor scanner & it will tell you where the problem lies. Most likely 1 of the sensors (valve stems) is faulty & needs to be replaced. Most any tire store will have the proper scanner needed.

Posted on Aug 28, 2010

Ad
  • 193 Answers

SOURCE: The "serv tpm" light is

Service Tire Pressure Monitor, either you have low tires or your "tire pressure monitors" are failing

Rate my answer witht the thumbs ..........Thanks

Posted on Dec 03, 2010

  • 1608 Answers

SOURCE: If I take out the tire pressure sensors from my

No.Because the tire pressure monitor is looking for a frequency from the sensors and does not see it.There for the light will stay on constantly.If you have a light that is constantly on and the tire pressures are all fine.Then you need to relearn the tire pressure monitor to make the light go off.Unless you have a bad sensor.There is a special tool for relearning the tire pressure monitor.It also has to be put in learn mode to perform this.Which is done with your keyless entry fob or in your case you apply the parking brake turn the key on and turn the light switch from off to park 4 times within 4 seconds.The horn will chirp twice.this means the system is in learn mode.This is where the special tool comes in.you need to go to a repair shop that has a tool for relearning.If the sensors are all good the light will go off.Hope this has helped.Good luck.

Posted on Dec 15, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reset the check tire pressure indicator


Using the Driver Information Center (DIC)
Important: After resetting, the tire pressure monitoring (TPM) system requires up to 8 km/h (5 miles) of flat, smooth road straight line driving in each of the 4 speed ranges to complete the calibration process. For further information, refer to Tire Pressure Monitor Description and Operation . If the TPM system does not reset, refer to Driver Information Center (DIC) Switch Inoperative .
  1. Set all tire pressures to the recommended kPa/psi. Refer to Vehicle Certification, Tire Placard, Anti-Theft, and Service Parts ID Label .
  2. Turn ON the ignition, with the engine OFF.
  3. Press the vehicle information button until TIRE INFLATION MONITOR SYSTEM PRESS (down/left arrow) SWITCH TO RESET is displayed.
  4. If the system is being reset due to a low tire pressure condition, press and hold the down/left arrow button until TIRE INFLATION MONITOR SYSTEM HAS BEEN RESET is displayed. If the system is being reset due to a tire rotation, press and hold the down/left arrow button for 5 seconds.
  5. Release the down/left arrow button and TIRE PRESSURE NORMAL is displayed.

Oct 08, 2015 | 2006 Pontiac Grand Prix

1 Answer

2005 grand Cherokee service tire pressure system


I found this on another site, it may help to understand what is happening, I also saw that there is a problem with the valve stems cracking since they're made out of aluminum and causing that problem. Here's the explanation provided on another site:

RodneyJ Answered 6 years ago
If a customer with a 2005 or later DaimlerChrysler vehicle equipped with Tire Pressure Monitoring (TPM) is concerned that the TPM lamp is on continuously, please be sure to inform the customer that the system is in place to warn of a low tire pressure situation, and a system diagnosis may not be required. The customer should be aware of the following: The Tire Pressure Monitoring (TPM) System will warn the driver of a low tire pressure based on the vehicle recommended cold placard pressure (the placard is located on the drivers side B-pillar).
The tire pressure will vary with temperature by about 6.9 kPa (1 psi) for every 6.5 Degrees C (12 Degrees F). This means that when the outside temperature decreases, the tire pressure will decrease - the customer should adjust his tire pressure for this decrease in pressure - please refer the customer to his vehicle owner's manual for information on how to properly inflate his vehicle's tires. The tire pressure will also increase as the vehicle is driven - this is normal and there should be no adjustment for this increased pressure.
The TPM System will warn the driver of a low tire pressure if the tire pressure falls below the low pressure warning threshold for any reason, including low temperature effects.
The TPM System will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above recommended cold placard pressure. Once the low tire pressure warning has been illuminated, the tire pressure must be increased to the recommended cold placard pressure in order for the TPM warning lamp to be turned off. The system will automatically update and the TPM warning lamp will extinguish once the updated tire pressures have been received. The vehicle may need to be driven for up to 10 minutes above 25 kph (15 mph) to receive this information.


FOR EXAMPLE:

A 2006 300 has a recommended cold (parked for more than 3 hours) placard of 207 kPa (30 psi).

If the ambient temperature is 18 Degrees C (65 Degrees F) and the measured tire pressure is 186 kPa (27 psi) the TPM lamp will be OFF.

IF NOTHING IS DONE TO THE AIR PRESSURE IN THE TIRES and the ambient temperature drops to 20 Degrees F (-7 Degrees C) while the vehicle is parked, the approximate tire pressure will be 157 kPa (23 psi) and the TPM lamp will be ON.

IF THE VEHICLE IS DRIVEN TO REACH NORMAL OPERATING TEMPERATURE

WITHOUT ADJUSTING THE AIR PRESSURE and the ambient temperature stays at -7 Degrees C (20 Degrees F), the approximate tire pressure will rise to 186 kPa (27 psi) and the 1PM lamp will be ON.

To turn the TPM lamp OFF the tires must be inflated to the vehicle recommended cold placard pressure.

In order to properly maintain vehicle tire pressure, please refer to the owner's manual for additional information regarding tire inflation.

NOTE :Tire pressure should always be set based on cold inflation tire pressure (defined as the tire pressure after a vehicle has not been driven for more than 3 hours - and in outside ambient temperature).

Seasonal temperature changes will affect tire pressure, and the TPM system will monitor the actual tire pressure in the tire.
If a diagnosis of the system is required (for example, the lamp did not extinguish, or the lamp is flashing), please refer to service information available in TechCONNECT for additional information for TPM diagnosis. Please be aware that if the Wireless Control Module (WCM) is replaced, the TPM placard values may need to be reprogrammed. The TPM placard values do NOT need to be updated if the WCM has NOT been replaced, the TPM placard values are properly set at the factory.

Jan 23, 2014 | Cars & Trucks

1 Answer

SERV TPM LIGHT IS ON AFTER CHANGING TIRES


That Must be a Sensor on The Disc Brake Pads Are They Not Worn Out If Not Its Touching Earth Somewhere , It Should Be a Single Wire With A Bullet Connector At The Brake Caliper

Mar 28, 2013 | 2008 Isuzu I 290

1 Answer

Programing tpms sensor 08 silverado


Hope this helps you.

LEARN MODE CANCELLATION
The TPM system will cancel the learn mode if more then 2 minutes have passed and no sensors have been learned, or if the system has been in learn mode for more than 5 minutes. If the learn mode is canceled before any sensor has been learned, the PDM will remember all current sensor IDs and their locations.

CAUTION: Before proceeding with the steps below, ensure that no other sensor learn procedure is being performed simultaneously, or that tire pressures are not being adjusted on a TPM equipped vehicle within close proximity.

STEP BY STEP:
  1. Turn "ON" the ignition, with the engine OFF.
  2. Apply the parking brake. IMPORTANT: If the learn mode cannot be enabled, ensure the TPM system is enabled in the PDM.
  3. Turn the exterior lamp switch from "OFF" to parking lamps 4 times within 4 seconds. A horn chirp will sound and the low tire pressure light will begin to flash indicating the learn mode has been enabled.
    CAUTION: Over inflating tires may cause personal injury or damage to the tires and wheels. When increasing tire pressure do not exceed the maximum inflation pressure as noted on the tire sidewall.
    IMPORTANT: If a horn chirp does not sound after 35 seconds for any of the 4 sensors, turn the ignition "OFF" to exit the learn mode and repeat the procedure from step 1.
  4. Starting with the left front tire, increase or decrease the pressure for 8-10 seconds, or until a horn chirp sounds. The horn chirp may occur before the 8-10 second pressure increase/decrease time period has been reached, or up to 30 seconds after the 8-10 second pressure increase/decrease time period has been reached.
  5. After the horn chirp has sounded, proceed as in step 4 for the next 3 sensors in the following order:

    Right front
    Right rear
    Left rear
  6. After all sensors have been learned, exit the learn mode by turning "OFF" the ignition.
  7. After the learn mode has been exited, adjust all tire pressures to the recommended psi
  8. After adjusting all tire pressures to the recommended psi, run the tire pressure check in the DIC to see that the correct pressure is listed.

Oct 31, 2012 | Cars & Trucks

3 Answers

I have a chevy colorado 2007. The "serv tpm" light


TPM THAT MEANS TEMPOMAT CRUISE CONTROL.CHECK TO SEE IF BRAKE LIGHTS WORK.IF NO CHECK BRAKE LIGHT SWITCH FUSE. IF FUSE OKAY BRAKE LIGHT SWITCH FAULTY OR YOU HAVE OPEN WIRE FROM BRAKE SWITCH TO FUSE BOX.SEE YOUR BRAKE SWITCH DEACTIVATES THE CRUISE CONTROL SYSTEM.PROBLEMS WITH BRAKE PEDAL POSITION SWITCH WILL SET OFF CRUISE CONTROL WARNING LIGHT.IF BRAKE SWITCH OKAY.THE DEALERSHIP HAS TO DIAGNOSIS AND FIX PROBLEM.

Dec 03, 2010 | 2007 Chevrolet Colorado (Extended Cab) New...

2 Answers

What does it mean when the warning SERV_TPM come on


Hello, SERV-TPM means Service Tire Pressure System. There could be several items to bring up this message. It could be a bad sensor in one of the wheels. It could also be the sensors require programming. The best way to find out is to have the system checked for codes. Before you do any of the above. check the placard on the drivers door for the correct pressure then check each tire with a gage. Thank you

Sep 07, 2010 | 2006 Hummer H3

2 Answers

A message on my dash came on say serv TPM...any idea what this is?


Tire pressure monitor. First check all tires for proper inflation. If 1 or more is low fill to proper psi. If all are correct need to plug into tire pressure monitor scanner & it will tell you where the problem lies. Most likely 1 of the sensors (valve stems) is faulty & needs to be replaced. Most any tire store will have the proper scanner needed.

Aug 28, 2010 | 2007 Chevrolet Colorado (Extended Cab) New...

1 Answer

Check tpm system comes up on screen, when u first start auto, then changes to wheel pressure screen, what do i do to reset


As long as the tires are all within 3 psi of each other ,The system will automatically reset and the TPM warning lamp will go off, once the updated tire pressures have been received. The vehicle may need to be driven for up to 10 minutes above 15 mph to receive this information.

A system fault can occur by any of the following scenarios:
1) Jamming due to electronic devices or driving next to facilities emitting the same Radio Frequencies as the TPM sensors.
2) Installing some form of aftermarket window tinting that affects radio wave signals.
3) Lots of snow or ice around the wheels or wheel housings.
4) Using tire chains on the vehicle.
5) Using wheels/tires not equipped with TPM sensors."

Also, if you have the premium TPM system, the spare tire being low could trigger it, or with either the base or premium system, if you have a flat and change to a spare, the original flat tire could keep it from re-setting. And of course, a faulty sensor could be the problem.

There is a re-setting tool, but that should only be needed if the tire positions are changed (like if you rotate your tires), and that's only so that it can accurately tell you which tire is low, as opposed to turning off a warning light.

Unhooking the battery will NOT reset it

Aug 02, 2009 | Dodge Caliber Cars & Trucks

1 Answer

06 dts tire monitor reset button?


Programming TPM Sensors
1. Turn the ignition to ON.
2. Press the key fob lock and unlock buttons simultaneously for several seconds. The horn will chirp when the TPM
programming mode is activated. Important: If the TPM programming mode cannot be entered, check if the DIM is
configured with the correct RPO codes.
3. Starting with the Left Front Tire
4. Install the J 41760 over the left front valve stem. Magnets from Radio Shack, P/N 64-1888 (at $2.99), will also work.
They're too small to go over the valve stem cap, but once you remove it they slip over the valve stem just fine
instead of the GM tool.
5. The horn will sound, indicating the Left Front TPM sensor is programmed. Important: If the horn does not sound after
15 seconds, remove then reinstall the TPM sensor programming tool or place the magnet alongside the valve stem.
6. When the horn sounds, proceed to program the next TPM sensor in the following order:
o Right Front Tire
o Right Rear Tire
o Left Rear Tire
7. After the Left Rear sensor is programmed, the horn will sound twice to indicate programming is complete.
Programming Cancellation
1. The programming mode will be canceled if any of the following conditions are met:
o The ignition is turned OFF.
o All four sensors have been programmed.
o The TPM system has been in the program mode for longer than 5 minutes and no sensors have been learned.
2. If more then one minute has passed before the next sensor is programmed, all previously stored codes are
erased from the receiver's memory.
after driving around for a few blocks, if the pressure does not match the tire pressure for each wheel, then the sensor is bad.

Oct 15, 2008 | 2006 Cadillac DTS

Not finding what you are looking for?
2007 Chevrolet Colorado (Extended Cab) New Cars Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...