Question about 2004 Chevrolet Malibu Maxx

Open Question

Replace oil pan gasket - 2004 Chevrolet Malibu Maxx

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6982 Answers

SOURCE: replac 2003 monte carlo oil pan gasket

To remove the oil pan on any vehicle, first remove anything obviously in your way...starter, exhaust pipe etc. Then disconnect the engine mounts and raise engine to gain sufficient clearance between frame and pan. You cannot support the engine from under the pan so either use a fixture above the engine or put blocks between mounts and engine to support it. After all rail bolts have been removed, remember that the oil pump pickup will interfere with removal somewhat but pan can be maneuvered around it. Anything preventing you from getting the pan out will then need to be removed or moved as they are identified. Be careful when raising the engine that you do not break anything above it as it comes up.

Posted on Jun 09, 2009

  • 462 Answers

SOURCE: OIL PAN GASKET LEAK

The engine has to be supported and the cradle under the engine has to be removed. After everything is reinstalled the front end has to be realigned.

Posted on Sep 13, 2009

Testimonial: "Thanks for your help, but i think i need a little more info. before tring this."

  • 4 Answers

SOURCE: changing oil pan gasket on 02 impala ls 3.8

The engine does have to be raised. The bolts are not easy to get to until the engine is lifted and the engine mount is removed. I'm doing this job right now and the book time is around 5 hours.

Posted on Jan 30, 2010

  • 7353 Answers

SOURCE: How do you replace a gasket and cover for timing

the oil pan will need to be removed to repalce the rear seal, so replace the front seal and gasket then, replace the timing chain/gears if sloppy, then reinstall the oil pan.

Posted on Dec 11, 2010

  • 492 Answers

SOURCE: well i have a 1998

Water in the oil is usualy from a leak in the cyninder head gasket. Sometimes you can seal the leak with a radiator additive. If the car starts to run hot or if you see the watery oil on the dip stick you should get the car to a shop for a repair estimate.

Posted on Mar 13, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove oil pan on a 2001 gmc Sonoma pick up truck to replace gasket


1993 GMC SONOMA 2.6 CYL V6 NOT 4x4 OIL PAN ...

? 2:31
https://www.youtube.com/watch?v=1KsRTlnW7Cg
Sep 27, 2011 - Uploaded by JohnSmiths8379858
trying to reomove the oil pan to this truck has been sitting for about 6 ... 1993 GMC SONOMA 2.6 CYL V6 NOT 4x4 OIL PAN REMOVAL "HELP!

Oil Pan Gasket: How to Change Oil Pan Gasket for 2001 ...

www.2carpros.com/questions/2001-gmc-sonoma-oil-pan-gasket
Mar 18, 2011 - How to change oil pan gasket for 2001 sonoma, can i get away with just raising the engine two inches to ... 2001 GMC Sonoma • 4 cylinder 2WD Automatic • 150,000 miles ... You need to remove the engine to get the sump off.

Nov 28, 2015 | GMC Cars & Trucks

1 Answer

How to replace oil pan gasket dodge caravan 2005 3.3l


jack up on jack stands, drain oil, remove all pan bolts, clean pan, use new gasket, replace bolts to torque specs do not over tighten it will tear the gasket. DO NOT USE GASKET SEALER OR PERMATEX IT MAKES GASKET SLIP

Mar 09, 2015 | 2005 Dodge Caravan

3 Answers

Need to replace oil pan gasket for 1996 Ford F-150 2wd, I-6


Yes you can do it yourself.
Its not very easy,but with basic Auto repair tools the task can be easily completed.

=========
There are few help links with solutions to complete these task.
I suggest you to refer these links and view its procedure.

-------
Click the link below:----
------------
How to Replace an Oil Pan Gasket?
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-oil-pan-gasket.html
-----------

KIA Sportage leaking oil from oil pan?

Go to Newly Launched

FREE Car repair gu
obyme.blogspot.com/2011/11/kia-sportage-leaking-oil-from-oil-pan.html" http://howtobyme.blogspot.com/2011/11/kia-sportage-leaking-oil-from-oil-pan.html
----------------
Oil pan Gasket on 1998
Toyota Tercel?
http://howtobyme.blogspot.com/2011/11/oil-pan-gasket-on-1998-toyota-tercel.html

-------------
VALVE COVER GASKET REMOVAL GUIDE http://technoanswers.blogspot.in/2012/06/valve-cover-gasket-removal-guide.html
--------- Car oil leaks from valve cover gasket? http://schematicsdiagram.blogspot.com/2011/12/car-oil-leaks-from-valve-cover-gasket.html

------------
How to replace Oil Pan on 2008 Honda Odyssey?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-oil-pan-on-2008-honda.html

-----------
How to replace Oil Pressure Sensor on 2008 Honda Odyssey?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-oil-pressure-sensor-on.html

------------
2004 Chevrolet Express Van: Oil pressure sending unit replacing? http://whoisbyme.blogspot.in/2012/06/2004-chevrolet-express-van-oil-pressure.html
-------------
HOW TO REPLACE AN OIL PUMP
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-oil-pump.html
-------------
HOW TO CHANGE ENGINE OIL AND FILTER
http://schematicsdiagram.blogspot.com/2011/07/how-to-change-engine-oil-and-filter.html
--------------
HOW TO REPLACE AN OIL PRESSURE SWITCH (SENSOR)
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-oil-pressure-switch.html


-------------

How to Check Differential Oil Leaks and Replace Oil
http://schematicsdiagram.blogspot.com/2011/07/how-to-check-differential-oil-leaks-and.html
-----------
HOW TO PERFORM A BASIC ENGINE TUNE UP-OIL CHANGE
http://schematicsdiagram.blogspot.com/2011/08/how-to-perform-basic-engine-tune-up-oil.html

----------
HOW TO RESET OIL CHANGE INDICATOR? http://whoisbyme.blogspot.in/2012/07/how-to-reset-oil-change-indicator.html

------------
These details will help.
Thanks.

Nov 25, 2012 | Cars & Trucks

2 Answers

What all has to be taken off to get to to the oil pan gasket


Oil Pan REMOVAL & INSTALLATION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain the crankcase.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Oil level indicator harness connector, if equipped
    • Exhaust Y-pipe, if needed
    • Transaxle assembly from the vehicle.
    • Oil pan bolts and the oil pan
    To install: NOTE: The oil pan gasket is reusable unless it is damaged. Do not remove the gasket from the oil pan groove unless gasket replacement is required.
  4. Thoroughly clean the inside of the oil pan and the cylinder block contact surface. If the oil pan gasket is being reused, be careful not to damage it. Do not expose the gasket to cleaning solvents.
  5. If a new gasket is being installed, start the gasket into the oil pan groove and work the gasket into the groove in both directions. Once the gasket is exposed to oil, it will expand and no longer stay in the groove without wrinkles. If this condition exists, replace the gasket.
  6. Install or connect the following:
    • Oil pan. Torque the bolts, in sequence, to 89 inch lbs. (10 Nm).
    • Oil level indicator connector, if removed
    • Transaxle assembly, if removed
    • Y-pipe, if removed
    • Flywheel cover, if removed
    • Oil pan drain plug. Torque it to 15 ft. lbs. (20 Nm).
    • Negative battery cable
  7. Refill the crankcase.
  8. Run the engine and check for leaks. Fig. 1: Oil pan bolt torque sequence 7922vg08.gif
prev.gif next.gif

Jan 01, 2011 | 2002 Cadillac Deville

2 Answers

How do I remove the oil pan gasket from my 1999 Cadillac Deville Concours


Oil Pan REMOVAL & INSTALLATION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain the crankcase.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Oil level indicator harness connector, if equipped
    • Exhaust Y-pipe, if needed
    • Transaxle assembly from the vehicle.
    • Oil pan bolts and the oil pan
    To install: NOTE: The oil pan gasket is reusable unless it is damaged. Do not remove the gasket from the oil pan groove unless gasket replacement is required.
  4. Thoroughly clean the inside of the oil pan and the cylinder block contact surface. If the oil pan gasket is being reused, be careful not to damage it. Do not expose the gasket to cleaning solvents.
  5. If a new gasket is being installed, start the gasket into the oil pan groove and work the gasket into the groove in both directions. Once the gasket is exposed to oil, it will expand and no longer stay in the groove without wrinkles. If this condition exists, replace the gasket.
  6. Install or connect the following:
    • Oil pan. Torque the bolts, in sequence, to 89 inch lbs. (10 Nm).
    • Oil level indicator connector, if removed
    • Transaxle assembly, if removed
    • Y-pipe, if removed
    • Flywheel cover, if removed
    • Oil pan drain plug. Torque it to 15 ft. lbs. (20 Nm).
    • Negative battery cable
  7. Refill the crankcase.
  8. Run the engine and check for leaks. Fig. 1: Oil pan bolt torque sequence 7922vg08.gif
prev.gif next.gif

Nov 05, 2010 | Cadillac DeVille Cars & Trucks

1 Answer

How to replace oil pan gasket on 2002 deville


Oil Pan REMOVAL & INSTALLATION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain the crankcase.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Oil level indicator harness connector, if equipped
    • Exhaust Y-pipe, if needed
    • Transaxle assembly from the vehicle.
    • Oil pan bolts and the oil pan
    To install: NOTE: The oil pan gasket is reusable unless it is damaged. Do not remove the gasket from the oil pan groove unless gasket replacement is required.
  4. Thoroughly clean the inside of the oil pan and the cylinder block contact surface. If the oil pan gasket is being reused, be careful not to damage it. Do not expose the gasket to cleaning solvents.
  5. If a new gasket is being installed, start the gasket into the oil pan groove and work the gasket into the groove in both directions. Once the gasket is exposed to oil, it will expand and no longer stay in the groove without wrinkles. If this condition exists, replace the gasket.
  6. Install or connect the following:
    • Oil pan. Torque the bolts, in sequence, to 89 inch lbs. (10 Nm).
    • Oil level indicator connector, if removed
    • Transaxle assembly, if removed
    • Y-pipe, if removed
    • Flywheel cover, if removed
    • Oil pan drain plug. Torque it to 15 ft. lbs. (20 Nm).
    • Negative battery cable
  7. Refill the crankcase.
  8. Run the engine and check for leaks. Fig. 1: Oil pan bolt torque sequence 7922vg08.gif
prev.gif next.gif

Oct 29, 2010 | 2002 Cadillac Deville

1 Answer

Oil pan


Replacing an Oil Pan Gasket
  • Drain oil through plug located at the bottom of oil pan.
  • Remove bolts around edge of the oil pan. There are probably around 8 of them.
  • Drop oil pan.
  • Clean gasket material from both block and oil pan.
  • Install new gasket.

Mar 12, 2010 | 1992 Honda Accord

1 Answer

Replace oil pan gasket 2002 chrysler 300m


The owner of the car should be able to locate and replace oil pan gasket .prepare the equipment to be used .Drain the oil from the oil pan ,spill it to an empty big can that can carry the oil from the oil pan.Then twist the bolts that connect the oil pan to the engine.After removing the bolts then you have take the old gasket off to the oil pan.After taking off the old gasket then you have to replace it with the new oil pan gasket.then return the oil pan with the new gasket. twist the bolt back until the oil pan that connect the oil pan with the engine.And return the drain plug twist until it will not spill.

Sep 30, 2009 | 2001 Chrysler 300M

2 Answers

Help


not oil pan but gasket remove oil pan scrape off all old gasket and put on new one the best thin to do is glue it on the oil pan first and let dry with bolt holes in line the glue it to block but this might no be the problem headgasket could leak oil pump gasket valve cover gasket

May 31, 2009 | 1994 Mercury Tracer

1 Answer

Gasket needs replacing


then you need to replace the gaskets drain oil from oil pan take all bolts out and drop the pan as far as valve pan covers buy rubber gaskets not cork they are a lot more pliable and less prone to leak

May 22, 2009 | 1994 Ford Aspire

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...