Question about 2005 Nissan Almera Tino

Open Question

Red car shaped light flashing in almera

But goes away when ignition is switched off

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Nissan Almera keeps cutting out completely whilst driving?


run the fault codes and look for cam/crank position sensors.
faulty or loose connections may cause this fault. If you have more than 1 key in the ignition then it has been known that the mass of swinging keys will switch off the ignition
(current recall on all GMC ignition switches for just this reason)

Feb 13, 2015 | 2005 Nissan Almera 1.6

1 Answer

How do i reset central locking on a micra 04 reg


Try the following:

"KEY FOB PROGRAMMING
NISSAN
SYSTEM DESCRIPTION
The Central Door locking is controlled by the Multi-Remote Control system which controls
the door locking, door super locking and hazard reminder. When the doors are locked and
unlocked the unit flashes the hazard lights once for lock and twice for unlock.
A maximum of four remote controls are allowed to be programmed.
ALMERA
ALMERA TINO
PRIMERA
MAXIMA
MICRA
SERENA
VANETTE CARGO
TERANO II
Ensure all the doors have been unlocked, either by using a good transponder key or remote
control plip key.
Procedure
1. Turn the ignition switch from Position 0 to ON 6 times within 10 seconds.
2. Then turn ignition switch to OFF position. Leave key in ignition switch.
3. After 2 seconds, the system will enter programming mode and will flash the warning
lights twice.
4. Press and HOLD the unlock button on the Plip.
5. While pressing the unlock button, press the lock button 3 times.
6. Release the unlock button.
7. The warning lights will flash once to indicate successful programming.
8. Repeat procedure 4 to 7 for up to 4 plip key?s.
9. When completed turn ignition ON, and the warning lights will flash 2 times.
10. Remove key, and check all plip key?s for operation.
NOTE : The programming mode will stop when either the ignition is switch ON, 4 plip keys
have been programmed or no input signal either from the switch or plip keys has been received
for 120 seconds."

Mar 12, 2012 | Nissan Cars & Trucks

1 Answer

A red flashing car shape light flashing on my 06 toyota sienna van?


Is the immobilizer, if there is no key in the ignition is ok if flashes, if it flashes when the key is in the ignition the key is bad car wont start.

Dec 31, 2010 | 2006 Toyota Sienna

1 Answer

Oil change light how do you reset


REMOVE THE FUSE COVER ON LEFT DRIVER SIDE OF DASH.INSIDE FUSE BOX IS A RED RESET BUTTON.TO RESET OIL CHANGE LIGHT.TURN ON THE IGNITION SWITCH WITH ENGINE NOT RUNNING.WITH IGNITION SWITCH ON POSITION,PRESS THE RED RESET BUTTON.WHEN THE CHANGE OIL LIGHT STARTS TO FLASH ,PRESS AND HOLD RESET BUTTON AGAIN.THE RESET IS COMPLETE WHEN YOU HEAR THE CHIMES AND THE CHANGE OIL LIGHT GOES OUT.

Sep 18, 2010 | 1999 Oldsmobile Alero

1 Answer

Why does red light in the shape of a car flashes


the red light is telling potential thieves that the car is immobilsed(dead) without the right key.....

Apr 18, 2010 | 2006 Toyota Corolla

1 Answer

P reg merc c180. red light flashes on rear view mirror when drivi


If you have a small odd shaped key on the keyring there is a socket under the steering wheel (in the plastic housing) which mine fitted. By turning the key left or right in the socket it resets the light. I found that the flashing light indicated that the alarm had been triggered at some time when I had been away from the car and had switched itself off after a time. If you have this key you could try that.

Jun 25, 2009 | 2003 Mercedes-Benz C-Class

1 Answer

Lotus elise 2005 fob and key does not work


Re-synchronize the FOB if the problem is with just one key.

1. Hold down both buttons simultaneously until the fob LED goes out. (10 seconds)

2. Release both buttons -- the LED should come on and stay on.

3. Press the larger fob button for a second, and the LED should flash.

IF re-synchronization doesn't work, you may have to replace the fob. Call customer service with your PIN (on the key-card that came with the keys). IF you don't have the PIN, then you need to call customeor service to confirm/register your ownership of the car.

If the keys are re-synchronized and it still doesn't work:

Re-program.

1. Re-synchronize as above, if you have not done so.

2. Turn the ignition on 3 times within 7 seconds. The red light above the odometer should light and stay on for 3 seconds.

3. Enter the PIN. Immediately after the red light goes out as per 2 above, switch on the ignition and count the number of flashes until it equals the number of the first digit on your PIN, then turn the ignition off, then on again. Do this for all four numbers.

4. What a pain, but if you get it wrong on a count, then you can restart by turning the ignition off for 10 seconds.

5. After the fourth digit, if the PIN is correct, the red light will stay on. Then you can re-test the fobs, and it should work.

Otherwise, call customer service.

Hope this helps.

Jan 02, 2009 | 2005 Lotus Elise

3 Answers

Key fob not working


hello mate.. if it has stopped working you might want to check the battery first.. if you are sure that the battery is fine then consider reprogramming the fob to your car.. here are the steps to follow.. NISSAN

Remote Control Fob Procedures:

The Central Door locking is controlled by the Multi-Remote Control system which controls
the door locking, door super locking and emergency hazard reminders.

When the doors are locked and unlocked the unit flashes the hazard lights once for lock and twice for unlock.

A maximum of four remote controls are allowed to be programmed:

ALMERA
ALMERA TINO
PRIMERA
MAXIMA
MICRA
SERENA
VANETTE CARGO
TERANO II

Ensure all the doors have been unlocked, either by using a good transponder key or remote
control plip key.

Procedure:
1. Turn the ignition switch from Position 0 to ON 6 times within 10 seconds.
2. Next, turn ignition switch to OFF position. Leave key in ignition switch.
3. Wait 2 seconds then the system will enter programming mode and will flash the warning
lights twice.
4. Press and HOLD the unlock button on the Plip.
5. While pressing the unlock button, press the lock button 3 times.
6. Release the unlock button.
7. The warning lights will flash once to indicate successful programming.
8. Repeat procedure 4 to 7 for up to 4 plip key's.
9. When completed turn ignition ON, and the warning lights will flash 2 times.
10. Remove key, and check all plip key's for operation.
NOTE : The programming mode will stop when either the ignition is switch ON, 4 plip keys
have been programmed or no input signal either from the switch or plip keys has been received
for 120 seconds.


http://www.autokeysquad.com/nissan-fob-programming



i hope this can help you.. :)

Jul 28, 2008 | 2005 Nissan Sentra

Not finding what you are looking for?
2005 Nissan Almera Tino Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...