Question about Suzuki Aerio

Open Question

Suzuki alto gear knob how to remove

How can you get gear knob off to replace with new one

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 13 Answers

SOURCE: gear knob removal bmw 318 ci

It's very simple. Involves a bit of fore arm strenght.
It should pull straight off. Just put one hand around the gear knob & your other hand supporting or gripping with both.
Just pull straight up. It shouldn't need much force. A small amount of glue may have been used to help hold it in place.
The knob might come off leaving the plastic sleeve/insert in the shifter. Same again, just grip that & try pull it off. A vice grips should not be neccessary but if you need it be carefull not to apply too much pressure as you don't want to break the sleeve into pieces.
The new knob should have a sleeve with it. Normally it will be inserted & you should be able to just pop it straight on.
Make sure it's lined up properly. You probably noticed on the bare metal shifter that it has a notch normally running across from left to right. Well inside the knob if you can see in you will notice it has a plastic or metal piece that will fit into this notch. This is to stop the knob from spinning around or slipping!
Just push down on the top of the knob & try slide it over the shifter. It might not go down all the way with pushing so a few taps with you palm may be enough if you have big strong hands but if not be carefull & only use a rubber head hammer or something you can hold but won't mark or break the knob.
Put a towel or old t-shirt over the knob & use anythink heavy that you can hold easily with one hand & that has no sharp edges!
I don't think any glue should be neccessary but if you feel it needs a little & the knob is comming off or going on too easy then just a few drops on the sides of the bare metal shifter before sliding the knob back on should suffice!
Good luck!

Posted on Dec 18, 2008

Ad
bmw_tech_38
  • 113 Answers

SOURCE: removing and fitting a new gear knob bmw e46 318i man trans

Hi joserosa if this is a manual gearbox you just have to grip the gear knob and pull upwards until the gear knob is removed, the same principle is applied for a auto box but hold in the release button while removing, regards Mark.

Posted on Jan 25, 2009

  • 188 Answers

SOURCE: replacing deawoo kalos gear shifter/ gear knob

do not know the car. but some screw off and others just pull off ask at halfords. they know.

Posted on Mar 26, 2009

redhaze89
  • 854 Answers

SOURCE: how do i top up gearbox oil on suzuki alto?

....

7fe4395.jpg

Posted on Sep 10, 2009

  • 3 Answers

SOURCE: 03 Suzuki Alto - Dashboard, tail lights not working

I have this car it has huge electrical problems. Something in the computer/alternator/etc. I have no speedometer, all my internal lights are screwed up. I've had 2 alternators, a starter and 4 batteries in 2 years. Get rid of it.

Posted on Dec 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Peugeot 3008 gear knob replacement


The gear knob is an interference fit onto the gear lever. Tthis means it is just as tight as uncle scrooge. There is no thread it needs t be pulled off which takes some effort and good positioning in the back seat, care must be taken as to not knock yourself out when it comes loose, you can bet on it being that tight. To replace align knob and force it on by hitting with a rubber mallet or similar to prevent damaging new gearknob. Before you start unclip the leather boot or you will tear it. Good luck.

Aug 17, 2017 | Peugeot Cars & Trucks

1 Answer

How to replace a gear lever leather boot on a Honda 2.2 crv 58 plate


First, unscrew the original gear knoband remove completely.
yannis-albums-new+gear+knob++gaiter-picture7964-simply-remove-original-gear-knob.jpg


Next unclip the panel which covers the base of the gear knob. This unclips quite easily without the use of tools or screwdrivers. Pop it off from the top end first and then lifts out from the bottom.
yannis-albums-new+gear+knob++gaiter-picture7965-remove-gear-base-cover.jpg

Screw on the new gear knob. Once tightly fitting, put the gaiterover it.
Top Tip - use a cable tie to keep the new gaitor fitting snug! This stops it slipping down and looking saggy. Clip off the excess off the end of thecable tie.yannis-albums-new+gear+knob++gaiter-picture7966-tip-use-cable-tie-keep-new-gaitor-fitting-snug-audi-tt-leather-gaiter.jpg


Finally tuck the new gaiterin and ensure it is fitting snug. Then follow clip the plastic base cover back on. Sit back and look proudly at you new smart, quality gear knoband gaiter!

Oct 11, 2014 | Cars & Trucks

1 Answer

The button on the gear shift knob keeps popping out.


sounds like my problem. its just tthat plastic button that comes out so you have to find where it fell and put back in again. can replace the whole handle.

Sep 27, 2012 | 2001 Pontiac Grand Am

1 Answer

Can you change a gear shift knob on a 2003 Mini cooper S??


Yes it can be replaced and here is a LINK that shows how to do it.

May 29, 2012 | Mini Cooper S Cars & Trucks

1 Answer

I have a '94 F150, straight 6, 4wd, 5 speed manual trans. My transmission shifting knob popped out of it's position and was stuck in a gear. I opened up the cover and was able to move the gear manually...


it seems like your shift fork is in between gears you must remove the shift tower and align all the shift levers then drop the shift knob into the middle being neutral tighten it up and it should be ok but remember the replacement could be slightly thinner then the original and causing this new problem.

Nov 13, 2010 | Ford F-150 Cars & Trucks

2 Answers

How to install new gear shift "knob" to 1995 jaguar xj6


My 95 XJ6 does not have the allen screw, all you need to do is get a good grip and turn it loose.

Jun 05, 2010 | 1995 Jaguar XJ6

2 Answers

Replacing deawoo kalos gear shifter/ gear knob


do not know the car. but some screw off and others just pull off ask at halfords. they know.

Mar 26, 2009 | 2002 Daewoo Lanos

1 Answer

Removing and fitting a new gear knob bmw e46 318i man trans


Hi joserosa if this is a manual gearbox you just have to grip the gear knob and pull upwards until the gear knob is removed, the same principle is applied for a auto box but hold in the release button while removing, regards Mark.

Jan 25, 2009 | 2001 BMW 325

1 Answer

Removing Factory Gear Shift Knob for 2001 Jetta


On my 2000 jetta glx, I had to replace both the shift knob and boot as one. It is built as one unit. You have to pull the boot up over the shift knob, break/bend a clip to "unlock" the shift knob then pull up. I hope the new knob you got has the boot built in and comes with a new clip.

Jan 08, 2009 | 2000 Volkswagen Jetta TDI

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

313 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...