Question about Cars & Trucks

Open Question

Whats the position of timing belt on a honda d13b engine? Is it normally at advance 1 position or at a normal position?

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
c17hydro
  • 2984 Answers

SOURCE: 1996 Honda Accord Timing Belt Installation. I need help.

You didn't post the size of motor so please use the one that is for you:

2.2L (F22A1) ENGINES
Install the timing belt, around the pulleys, in the sequence shown


26f5cb1.gif

a9d5be6.gif

Posted on Jun 30, 2009

Ad
  • 51 Answers

SOURCE: 2003 Dodge Neon: P0016 (already replaced sensors, belt, tensioner

the computer may need to be reflashed. if it is running then it is not a bad sensor. either of those being bad would cause it not to run.

Posted on Aug 08, 2009

dttech
  • 4803 Answers

SOURCE: 1995 Honda Passport timing alginment 3.2 ltr 6VD1 engine

The crankshaft should have the timing mark on the crank pulley (Notch in the outer edge of the pulley near the keyway) It should align with the timing mark on the oil pump. (With the keway turned to about the 3 O'clock position.)

Align the marks on the camshaft timing pulleys with the corresponding dots on the front plate.

If you are installing a new belt, it should have 2 solid white lines printed on it that you would align with the timing marks on the cams and a dotted white line to align with the timing mark on the crank.

It makes a difference which way you put the belt on. (Which edge faces the front of the engine.) Most, but not all brands of belts have arrows and the word "FRONT" on them to tell you which edge of the belt shoud face the front of the motor. If there is no mark to tell you which edge is front, the letters on the belt must be able to be read correctly as viewed from the front of the vehicle.

Posted on Oct 30, 2009

Testimonial: "Thanks for bringing me back to reality... I just finished working on it and everything is fine. It really was that simple.... Thanks again."

perkins48
  • 14384 Answers

SOURCE: Volvo S40: P0014 - Exhaust Camshaft Position - Timing Over-Advanced (Bank 1)

Here's a link to your code.

Posted on Jun 22, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Honda odyssey won't start. Have done balance belt and timing belt. Just want to know your thoughts. Also whats the sequence of setting valves please F22B. Any recommendations will be good.


Most Hondas are interference engines. Did you replace the timing because of it dieing? Google interference engines. Go to their site. Look to your year make model and engine size. If it is an interference engine, the shop should have checked this first . These engines are trashed most times when the timing belt breaks.

Oct 27, 2016 | Honda Odyssey Cars & Trucks

1 Answer

My steering wheel become real stiff


fast or gradually in 10 years.?????
1: engine stalled?, normal..
2: engine at 800 rpm or more, not normal ?,belt fell of pump.

Nov 17, 2013 | 1998 Honda Accord

2 Answers

We changed teh timing belt on my 2002 honda civic and now it won't start. we rechecked the belt and it looks good maybe off 1 tooth. the engine cranks but nothing fires. We checked the compression on #1...


If the belt broke before you changed it,most likely bent the valves. As far as I know all honda engines are interference. Meaning if the belt timing is wrong the piston will hit the valves.
You wouldn't hear anything. Engine would spin really fast (no compression)
Only way to really tell is pull the valve cover and look at the valve height.
That would be a good way to be sure the marks are right also(the valves are closed when #1 is at top )

Mar 09, 2011 | Honda Civic Cars & Trucks

2 Answers

Wont start after timing belt and water pump replaced


Sounds like your timing marks aren't set correctly. Make sure you have spark and fuel. (Injector pulse)

Mar 03, 2011 | 1995 Honda Passport

2 Answers

Timing


Did the shop say the belt was on wrong? I suspect it was, and possibly still is. They may not have known where the original position was and did it wrong again as Honda reference marks can be a little vague. If the belt was out enough to make the engine back fire, then it is possible that valves were bent however the fact that it idled fine is good news. Does it still idle fine? Bent valves will prevent a smooth idle, a compression test would be a good idea. I would take it to another shop, preferably a Honda dealer and have it checked again.
cb7853f.jpg9d05abc.jpg

Feb 25, 2010 | 1995 Honda Passport

2 Answers

No spark, had ignition module tested by advance auto and said good, have power to positive and negative side? where's the problem?


Check the coil/coils for spark. If you have no spark at coils, check the camshaft sensor.does the motor sound normal during cranking? if not, you may have a broken timing belt or chain, whichever your vehicle is equiped with.Good luck

Feb 14, 2010 | 1991 Honda Accord

1 Answer

Whats the timing for the nissan sr20 motor in my 96 serena van.. cheers weetbix


GA16DE and SR20DE Engines



1. Start the engine and allow it to reach normal operating temperature.
2. Run the engine at 2000 rpm for 2 minutes and return to idle.
3. Turn the engine OFF and disconnect the throttle position sensor harness connector.
4. Start the engine and race the engine to 2000 rpm, 3 times.
5. Connect a timing light to the No. 1 spark plug wire and battery.
6. Loosen the distributor hold-down bolt and adjust the ignition timing to 10 degrees BTDC for the GA16DE and 15 degrees for the SR20DE engines.
7. Turn the engine OFF and reconnect the throttle position sensor harness.

_Ricky got this from the web

Aug 18, 2009 | 1996 Nissan Sentra

1 Answer

2003 Dodge Neon: P0016 (already replaced sensors, belt, tensioner


the computer may need to be reflashed. if it is running then it is not a bad sensor. either of those being bad would cause it not to run.

Jun 20, 2009 | 2003 Dodge Neon

2 Answers

Code error P1361 Honda CIvic LX 2002 -- What it really means? Appear Check engine light intermitent. In my case after Timing belt, water pump, tensor, oil seals and spark replacement. Car lose power and...


P1361 TDC Sensor Intermittent Interruption (I got this from Engine-Light-Help.com)
TDC should mean Top Dead Center.
It is the sensor that tells the computer the #1 cylinder piston is at the very top. And therefore, fires the spark plug.

Since the maintenance done above, I believe the the timing marks for the timing belt is not lined up properly. Being off by one tooth will cause this problem.

Mar 21, 2009 | 2002 Honda Civic

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...