Question about 1990 Honda Civic

Open Question

How to remove clutch pedal bracket from a honda civic 1990

Remove the clutch pedal assembly removal

Posted by Anonymous on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 6 Answers

SOURCE: honda civic pedal assembly

It should be a simple fix. If you go to a local dealer, it can be as easy as them pulling a pin, lowering the pedal and replacing the pin. If the car is newer, it is all electric and there are no hydrolic parts to depress. Good luck!!!

Posted on Oct 23, 2008

  • 2984 Answers

SOURCE: pedal assembly

Please take a look at this and tell me if this is your problem.

Posted on Mar 11, 2009

  • 9 Answers

SOURCE: 1990 honda civic windshield removal

the best way it to remove any trim mouldings and use a piano wire or gutar string to saw the sealent from the glass cut and wrap the ends of the wire around a wooden dowel otherwise you will have a real mess with the broken glass

Posted on Mar 20, 2009

  • 1 Answer

SOURCE: Clutch pedal bracket on my 91 Honda Civic Broke. shows exactly how to get the pedal bracket assembly out. Did you find a replacement bracket? If so, where?

Posted on Apr 29, 2009

  • 1 Answer

SOURCE: i need to know how to remove the font bumper on a

remove screws from ends of bumper x4,
remove bolts from under bumper x2
remove indicaters from bumper x2
remove 10mm head bolts from behind where indicater were x4
lift bumper up and out

Posted on May 04, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

How do I replace a rear hub assembly for a 2006 civic hybrid

Remove the wheel and the brake caliper/bracket assembly. Remove the center bolt from the hub assembly and pull the hub assembly off. Install in reverse order making sure the hub nut is torqued properly

May 09, 2015 | 2006 Honda Civic Hybrid

2 Answers

Why wont my 1989 honda civic start ? i replaced the starter and battery, wont start, not even off a jump start, but will off a push start get a dull thud sound from the main relay, could it be bad ?

Your Civic has a manual tranny - correct? The problem could be a bad Clutch Safety switch. Many Hondas are listed as having this switch with the manual tranny. The switch prevents the car from starting if the tranny is in gear and the clutch is not depressed, preventing the car from lunging forward. If the switch is there , it is located on the clutch pedal bracket. The switch has two wires, so if you remove the electrical plug from the switch and jump the plug, maybe the car will start? Good Luck!!!

May 22, 2014 | 1989 Honda Civic

1 Answer

Clutch pedal wont spring back,

If the clutch is good and works right, then probably the big spring on the clutch pedal under dash may have come loose or broke. You need to look at the pedal operation while you push and release. It's a bit of a job to work on the pedals. Not sure, but you may have to remove the pedal assembly to fix it. good luck.

Oct 26, 2011 | 1998 Honda Civic

2 Answers

Does anyone have a print out or do it yourself guide on removing a dashboard on 1990 honda civic 4 door? has a free online repair guide for your car. You can use it to
enlarge stuff like the JPEG images below, and get detailed instructions.


1988-91 Honda Civic Sedan (4-door) Dashboard Assembly Removal


1988-91 Honda Civic - non-sedan Dashboard Assembly Removal.

Apr 17, 2011 | Honda Civic Cars & Trucks

2 Answers

How do i change my clutch to a 1989 honda

That is a job for a trans repair shop

The engine has to be supported and
the transaxle removed

Figure $900.00

Mar 09, 2011 | 1990 Honda Civic

2 Answers

How to adjust clutch pedal on 86 mustang lx

clutch is supposed to be self adjusting. Here are instructions for replacing the adjuster:


See Figure 1

  1. Disconnect the battery cable from the negative terminal of the battery.
  2. Remove the steering wheel using a steering wheel puller, Tool T67L-3600-A or equivalent.
  3. Remove the lower dash panel section to the left of the steering column.
  4. Remove the shrouds from the steering column.
  5. Disconnect the brake lamp switch and the master cylinder pushrod from the brake pedal.
  6. Rotate the clutch quadrant forward and unhook the clutch cable from the quadrant. Allow the quadrant to slowly swing rearward.
  7. Remove the bolt holding the brake pedal support bracket lateral brace to the left side of the vehicle.
  8. Disconnect all electrical connectors from the steering column.
  9. Remove the 4 nuts that hold the steering column to the brake pedal support bracket and lower the steering column to the floor.
  10. Remove the 4 booster nuts that hold the brake pedal support bracket to the dash panel.
  11. Remove the bolt that holds the brake pedal support bracket to the underside of the instrument panel, and remove the brake pedal support bracket assembly from the vehicle.
  12. Remove the clutch pedal shaft nut and the clutch pedal, as outlined above.
  13. Slide the self-adjusting mechanism out of the brake pedal support bracket.
  14. Examine the self-adjusting mechanism shaft bushings on either side of the brake pedal support bracket, and replace if worn.

To install:
  1. Lubricate the self-adjusting mechanism shaft with motor oil and install the mechanism into the brake pedal support bracket.
  2. Position the quadrant towards the top of the vehicle. Align the flats on the shaft with the flats in the clutch pedal assembly, and install the retaining nuts. Tighten to 32-50 ft. lbs. (43-67 Nm).
  3. Position the brake pedal support bracket assembly beneath the instrument panel, aligning the four holes with the studs in the dash panel. Install the four nuts loosely.
  4. Install the bolt through the support bracket and into the instrument panel. Tighten to 13-25 ft. lbs. (18-34 Nm).
  5. Tighten the four booster nuts that hold the brake pedal support bracket to the dash panel to 13-25 ft. lbs. (18-34 Nm).
  6. Connect the brake lamp switch and the master cylinder pushrod to the brake pedal.
  7. Attach the clutch cable to the quadrant.
  8. Position the steering column onto the four studs in the support bracket and start the four nuts.
  9. Connect the steering column electrical connectors.
  10. Install the steering column shrouds.
  11. Install the brake pedal support lateral brace.
  12. Tighten the steering column attaching nuts to 20-37 ft. lbs. (27-50 Nm).
  13. Install the lower dash panel section.
  14. Install the steering wheel.
  15. Connect the battery cable to the negative terminal on the battery.
  16. Check the steering column for proper operation.
  17. Depress the clutch pedal several times to adjust the cable.
  18. 714c4a4.gif

Sep 24, 2010 | Ford Mustang Cars & Trucks

1 Answer

My honda civic break lights a permantly on even wheni stop and remove keys

replace the switch on the brake pedal,your brake lights are the only lights that are independant of the key switch on nearly all cars.....

Aug 25, 2010 | 1990 Honda Civic

1 Answer

I need instructions on how to remove/install headlight assembly on a 1990 civic ex 4 door

open the bonnet, unlock the latch for head lamp cover the and remove the head lamp cover and replace the head lamp.

Sep 18, 2009 | 1990 Honda Civic

1 Answer

Clutch pedal bracket on my 91 Honda Civic Broke. shows exactly how to get the pedal bracket assembly out. Did you find a replacement bracket? If so, where?

Dec 29, 2008 | 1992 Honda Accord

2 Answers

How do you replace a alternator

well, if you have a 1990 civic... you jack up the front end.. make sure to use a jack stand to ensure car will not fall while under it... remove the tire... first start by removing the bolts from the top of the alternator.. first 1) is the nut which bolts on a wire.... it should be on the top under a dust cover.. 2)..unclip the wires in the rear of the alternator they should just plug in with a clip style plug...3) remove the bolt in the bracket that adjusts the alternator belt tension.. 4) loosen the bolt in the end of the tensioning bracket so that the bracket swings free.. 5) now move to the side of the car where you removed the tire... and climb under car.. remove the bolt going through the bracket and tap it out...6) push the alternator up into the engine area where it will be secure and out of the way then remove the bracket the alternator was mounted to... after removing the bracket the alternator should have just enough room to be wiggled out...

Jul 28, 2008 | 1990 Honda Civic

Not finding what you are looking for?
1990 Honda Civic Logo

Related Topics:

182 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts


Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides