Toyota starlet engine torque data

Head Bolts Step 1-33 Ft. Lbs. Step 2- Additional 90 DegreesI would check in the service manual as well, just to be sure.

fel_pro_torque_specs_guide.pdf

PDF]Complete Cylinder Head Torque Specifications for Domestic ...

olybrake.com/pdf/fel_pro_torque_specs_guide.pdf

and engine block, tightening the head bolts compresses the gasket slightly ... by thehead bolts. PermaTorque® head gaskets are made with top-quality.

Toyota NZ engine - Wikipedia, the free encyclopedia

https://en.wikipedia.org/wiki/Toyota_NZ_engine

WikipediaThe 1NZ series uses aluminum engine blocks and DOHC cylinder heads. ... The 1NZ-FXE is the earliest 1.5 L (1497 cc) version built in Japan. ... Output is 57 kW (76 hp) at 5000 rpm with 115 Nm (85 lb·ft) of torque at 4000 rpm. ... The 1NZ-FXE Hybrid Synergy Drive in the Toyota Prius has won several International Engine of ...

2007 Toyota Yaris Cylinder Heads & Components at CARiD ...

toyota e engine guide - Toyotagtturbo.com

www.toyotagtturbo.com > ... > Modification/ Technical Questions
Sep 15, 2009 - 7 posts - ‎7 authors The 1E is a 1.0L (999 cc) carbureted 12 valve SOHC engine. ... Specs: 74 mm Bore 77.4 mm Stroke 9.6:1 Compression Ratio ... Engine Code Head Design Valves/Cylinder Date CC Peak HP Peak Torque Bore Stroke CR 1E ...

[PDF]Full page fax print - AMC Eagles Den

www.amceaglesden.com/images/Downloads/ENGINE%20MANUAL.pdf
All information and specifications in this manual are based on the latest data available at the time of .... 1E ENGINES Cylinder Head Bolt Torque Specifications ...

Either on top of crank pulley (harmonic ballencer) or on transmission housing close to engine there will be a rubber plug you can remove covering access port to view marks on torque converter.

Toyota 2c ...
USE NEW BOLTS...
Torque sequence:
You're driving a diesel single cylinder head engine. Engine head torque has to be done in specific order and stages if not can warp head or break bolts. Suggest you get torque sequence and torque specs from your Toyota dealer, they can give you correct answer. Don't trust answers on here, if you choose wrong specs. could end up messing up head.


Flywheel - Use a Sealer on bolt, Manual Transmission 88nm/65 ft lb... Auto Transmission 74nm/55 ft lb

Toyota 4A/ 5A-FE Cylinder Head Torque:
(a) Apply a light coat of engine oil on the threads and under the heads of the cylinder head bolts.
(b) Install the plate washer to each cylinder head bolt.
(c) Install and uniformly tighten the ten cylinder head bolts in several passes in the sequence.
Torque: 60 N-m (610 kgf-cm, 44 ft-lbf)
HINT: Cylinder head bolts are in length of 90 mm
(3.54 in.) and 108 mm (4.25 in.). Install the 90 mm
(3.54 in.) bolts (A) in intake manifold side positions.
Install the 108 mm (4.25 in.) bolts (B) in exhaust
manifold side positions.

Toyota Starlet L4-1290cc 4KE

40-47 Ft/lb

cylinder head bolts:

step one: 22 Ft-lbs.
step two: tighten additional 90 degrees
step three: tighten additional 90 degrees

Hi!

The Toyota Starlet is a fuel efficient compact car that replaced Toyota's Publica model in 1973 and was manufactured through the 1999 model year. The Starlet was sold new in the United States for only four years, from 1981 through the 1984 model year. Originally a rear-wheel drive car, the Starlet transitioned to front-wheel drive in 1984.

The 1981 to 1984 versions of the Starlet that were sold in the U.S. were powered by a 1.3 liter OHV engine with four cylinders and electronic fuel injection. The engine has a 2.95-inch bore and 2.87-inch stroke and produces 58 horsepower at 4,200 rpm. The 1981 and 1982 versions of the engine produced 67 ft-lbs of torque, and the 1983 and 1984 versions produced 74 ft-lbs of torque. The compression ratio is 9.5:1.
Hope that helps!!
EJ Kudelka