Question about Cars & Trucks

Open Question

Vital fitness rb350 recumbent bike error e1

The display on my recumbent bike shows E1 while beeping. The tension does not adjust either. Any ideas on how to fix this problem?

Posted by Anonymous on


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 336 Answers

SOURCE: vital-fitness-recumbent-bike instruction manual

Go to support on their website and you'll find an owners manual. murf427

Posted on Aug 30, 2012


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to repair if engine cannot race up when vehicle is running in Toyota Model KDN190R-CRPSYT vehicle?

If it is a Tercel or MR2, it is T and E1 terminals. Code 21 is main oxygen sensor signal fault. Code 51 is A/C signal on; DL contact off (in transmission shifter with diagnostic connector jumped). I have no idea what that 51 means.

May 28, 2015 | Toyota Cars & Trucks

1 Answer

How do the governor primary and secondary springs go on a model407777 type 0128 . E1

model and type are all very well but information as to what engine and application is vital for an answer.

Mar 13, 2015 | Cars & Trucks

2 Answers

Hi, I have a suzuki ignis 2004. I stayed out of electricity, so my blaupunkt radio needs a code. Please anyone help me. on a radio there is little sticker on the side with the following codes serial...

CODE 1793
Code Entry as Follows:

Switch Radio On - Display Shows
" CODE "
Press and Hold "BAND"
The display will now show " 10 - - - - "
Press preset " 1 " repeatedly for 1st Digit
Press preset " 2 " repeatedly for 2nd Digit
Press preset " 3 " repeatedly for 3rd Digit
Press preset " 4 " repeatedly for 4th Digit
If the correct code number is now shown
Press and Hold "BAND" to Enter

Dec 12, 2014 | 2004 Suzuki Ignis

1 Answer

Vital-fitness-recumbent-bike instruction manual

Go to support on their website and you'll find an owners manual. murf427

Aug 30, 2012 | Cars & Trucks

1 Answer

Cd error code e1

Hi there:
The E1 error code means the CD is upside down, dirty, or the wrong data format (CD-DA)

If you have tried several other disks and are having the same error message you can try to clean the optics with compressed air in a can like dust-off. If that does not resolve the problem you will have to contact an authorized service center for repair.

Hope helps.

Mar 22, 2012 | Cars & Trucks

1 Answer

1998 Corolla. Engine light is on, code PO420. Just got a tune up.

Hi Thomas,
Open the bonnet and look for the diagnostic socket, it has 'Diagnostic' imprinted on the lid....Open it and inside the cover you'll see a small directory...Make a bridge and connect 'T' to E1....Turn on the ignition and then count the number of flashes which are displayed by the engine check light. (that's the orange light showing an engine). Once you have that let me know and we'll identify the fault. As the engine has just been tuned, have a look at the air cleaner housing and make sure that the air temperature sensor has been connected....Looking from in front of the car the air cleaner is on your right hand side and the sensor is fitted on the back about half way down. Check visually for any other disconnected sensors which may have been overlooked.
Regards Johngee10

Feb 08, 2011 | 1998 Toyota Corolla

1 Answer

What is the ignition timing for toyota previa 1992

2,4 engine : 5° 700-750 rpm. but before you adjust timing, you need to bridge terminals TE1 or T1 with E1 of check connector. bridge should be removed after adjusting.
hope it helps

Oct 06, 2010 | 1992 Toyota Previa

1 Answer

How do I see/get error codes for my 1988 4Runner? (idling prob.)

The check connector is located near the No. 2 relay box. Short terminals T and E1 of the check connector. (jump together)
2. Turn the ignition ON. do not start engine.
3. Read codes by the number of flashes of the "CHECK ENGINE" WARNING LIGHT.
4. System normal: blink every 0.25 seconds.
5. Malfuction Code: light will blink a number of times equal to the malfuction code.Between first digit and second digit, 1.5 sec
Between code and code 2.5 sec, between all malfuction codes 4.5 sec
6. The diagnostics code series will be repeated as long as the connector terminals T and E1 are jumped.
7. Codes are 2 digit numbers

Feb 11, 2010 | 1988 Toyota 4Runner

1 Answer

Cruise control error codes E1

Change the transmission speed sensor

Aug 08, 2008 | 2006 Toyota Sienna

1 Answer


Your base ignition timing should be 10 deg. btdc.Make you a fused jumper wire and with the engine running jump terminals -te1 and e1.This will allow you to adjust base timing.Connect your timing light to spark plug wire number 1.Check your timing and adjust to 10 btdc if necessary.Good Luck!!!!

Aug 03, 2008 | Lexus GS 300 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides