Question about Volvo 740

Open Question

Remove shift lever

Can't get the pin(shift rod bolt?) out of manual shifter so that I can remove the chrome sleeve. Should it come out easily or does it require tapping it out? Seems to have a rubber boot or 'gasket' around it. Thanks.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 13 Answers

SOURCE: Transmission shift lever - 91 Toyota V6 4WD pickup

Easy fix! Remove boot, take out four screws, shifter pops up, replace bushing! Keep it in neutral before starting.

Posted on Aug 12, 2008

  • 1 Answer

SOURCE: Shift lever stuck in Park

is the car paked on a level ground? if not and the car is slightly sloping backwards. you need to get someone to give it a little push while you attempt to move the gear to D position.

Posted on Dec 30, 2008

  • 4 Answers

SOURCE: 92 Miata transmission shift boot replacement

The lower shifter boot is attached to the transmission by 3 10mm bolts. You will need to remove to center consoule and the upper shift boot that attaches to the car to be able to remove the lower boot. Then you can replace the lower boot.

Posted on Jan 04, 2009

468 Chevelle
  • 81 Answers

SOURCE: How Do I Remove & Replace Worn Inner Tie Rod Ends

Cut band clamp. use tie wrap. Special tool to remove inner tie rod. Autozone or others have them to rent. Must align after replacement

Posted on Mar 27, 2009

  • 750 Answers

SOURCE: Loose inner tie rods on '97 Dodge Dakota Sport 2WD

corect size wrench should work. count the number of turn it takes to remove each unit make note and install new units using those numbers

Posted on Jun 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Alright I have a few problems here. I have a 1987 dodge d50 manual transmission.. so the shifter linkage is really loose need some advice on how to tighten it? Also I can't shift in to 4th


I had a 1984 D50 years ago with a manual transmission. If I remember right, there is a boot covering the lower portion of the shift lever, and the boot was held in place by a frame screwed to the floor. If you remove the screws, and the knob on the shifter, you should be able to lift the boot and frame up off the shifter. Look where the shifter goes into the transmission, and see if there are visible bolts. Make sure these bolts are all there and are tight. (Don't force the bolts tight - make sure the shifter is located in the transmission properly.)
If the bolts are there and are all tight, then you have some problems internally in the selector rod(s) and/or shift forks, and the transmission will have to be removed and disassembled to repair it.

Nov 27, 2016 | Dodge Cars & Trucks

1 Answer

How do you adjust linkage for transfer case


SHIFT LINKAGE ADJUSTMENT
(1) Shift transfer case into 4L position. (make sure your shifter is fully in the 4L position)
(2) Raise vehicle.
(3) Loosen lock bolt on adjusting trunnion (Fig.
87).
(4) Be sure linkage rod slides freely in trunnion.
Clean rod and apply spray lube if necessary.
(5) Verify that transfer case range lever is fully
engaged in 4L position. (you can do this under the vehicle at the transfer case)
(6) Tighten adjusting trunnion lock bolt.
(7) Lower vehicle

Basically, you are just ensuring that the position you put the lever inside the vehicle is the same position that the transfer case lever is in and then tightening the locking bolt.

Jan 27, 2016 | Cars & Trucks

1 Answer

How to replace a shift lever for a 1966 lemans


I think you mean the column shift lever which is replaced by tapping out the pivot pin from under the base of the shifter. It is a chrome colored pin and will only come out if you tap it LIGHTLY from the bottom.

Apr 12, 2015 | Pontiac LeMans Cars & Trucks

3 Answers

How can i shift to neutral from the transmission it seems that the lever on the column is not working on 1974 chevy pick up


1/2ton I presume automatic.? Remove shift lever from trainsmisionn should be two clicks toward rear from lowest point

Feb 24, 2015 | Cars & Trucks

1 Answer

How do you remove the manual shift lever from a 1994 acura legend


YOU HAVE TO UNSCREW THE SHIFT LEVER KNOB. REMOVE THE CENTER CONSOLE.REMOVE THE RUBBER SHIFT LEVER BOOT AND THE DUST SEAL.YOU NEED TO RAISE SUPPORT VECHICLE ON JACKSTANDS ON LEVEL SOLID GROUND.YOU HAVE TO DISCONNECT THE EXTENSION ROD FROM THE TRANSAXLE.SIMPLY REMOVE THE BOLT THAT ATTACHES IT TO THE EXTENSION BRACKET.TO DISCONNECT THE SHIFT ROD FROM THE TRANSAXLE PUSH THE DUST BOOT FORWARD REMOVE THE CLIP AND DRIVE OUT THE SPRING PIN WITH A PIN PUNCH.DISCARD THE SPRING PIN.DO NOT REUSE IT.TO DISCONNECT THE REAR END OF THE SHIFT ROD FROM THE SHIFT LEVER REMOVE THE NUTS AND BOLTS.THEN REMOVE THE TWO NUTS AND WASHERS THAT RETAIN THE CHANGE BALL HOLDER TO THE UNDERSIDE OF THE EXTENSION ROD AND REMOVE THE CHANGE BALL HOLDER LOWER THE SHIFT LEVER DUST SEAL,SHIFT LEVER BALL SEAT,SHIFT LEVER AND EXTENSION ROD.INSPECT THE BUSHING AT THE FRONT END OF THE EXTENSION ROD AND REPLACE IT IF ITS CRACKED TORN OR WORN. REPLACE THE ORINGS IN THE BASE OF THE LEVER.BESURE TO LUBRICATE NEW O RINGS AND BUSHINGS WITH A SILICONE GREASE.USE A NEW SPRING PIN TO ATTACH THE SHIFT ROD TO THE TRANSAXLE.INSTALL EVERY THING BACK VISA VERSA.

Mar 02, 2011 | 1994 Acura Legend

1 Answer

The 4 wheel drive shifter is broken. How does the linkage to the transfer case come apart?


Shift Lever NOTE: Remove the shift ball only if the shift ball, boot or lever (7E067) is being replaced.
Removal
  1. Raise vehicle on hoist and position suitable safety stands under vehicle.
  1. Prior to removing the control lever assembly (7E069), be sure the shifter is in the 2H position.
  1. Loosen (do not remove) the nut retaining the shift handle (7E067) to the control lever assembly (7E069). Remove the shift handle (7E067) from the control lever assembly (7E069).
  1. Remove the vent hose (7D494) from the notch in the detent plate.
  1. Remove the control rod (7A315) from the control lever assembly (7E069). ani_caut.gif CAUTION: When removing the control rod (7A315) off the control lever assembly (7E069), do so very gently so as not to damage the control lever assembly.
  1. Loosen (do not remove) the large pivot bolt holding the control lever assembly (7E069) to the detent plate.
  1. Swing the control lever assembly (7E069) out of the way and remove the two bolts (39129-S2) retaining the detent plate to the transmission extension housing. Remove the entire control lever assembly from the vehicle.
Installation
  1. Prior to installing the control lever assembly, be sure the transfer case link (7B106) is in the 2H position (pointing upward).
  1. Install the two bolts (39129-S2) to retain the control lever assembly (7E069) to the transmission extension housing and tighten to 92-125 Nm (68-92 ft-lb). Refer to the following illustration for bolt hole application.
  1. Attach the control rod (7A315) to the control lever assembly (7E069).
  1. Tighten the large pivot bolt to 92-125 Nm (68-92 ft-lb).
  1. Attach the vent hose (7D494) into the notch in the detent plate so the white mark is flush to the outside surface of the plate.
  1. Install the shift handle (7E067) into the control lever assembly (7E069). Tighten the retaining nut to 27-38 Nm (20-28 ft-lb).
  1. Check transfer case for proper shifting and operation.

    c10894a.gif



    cc10895a.gif

Feb 27, 2010 | 1992 Ford F250

2 Answers

I need the location of a neutral safety switch on a 1999 buick century 3.1L.


I take it that you have an automatic transmission the shift selector /neutral saftey switch switch is located on top of the transmission were the shift cable connects to the trans. Remove the 13 mm nut in the center of the switch and remover the shift cable and lever noting the location of the lever. then remove the bolts holsing the switch to the transmission and the elec connector.

Feb 25, 2010 | 2003 Buick Century

1 Answer

I have a 97 f-250 7.3 with a manual trans. and it wants to jump out of reverse if I dont go to 1st gear and then to rev. first.


Sounds like the shift lever is not coming completely out of 2nd gear. So, by shifting into 1st gear, you recenter the shift lever. You can confirm this by going under the truck and moving the 1st - 2nd lever on the side of the transmission with your hand. If the shifter goes into reverse after you manually recenter the 1-2 lever, then you need to correct the problem that prevents the "normal" recentering of the 1-2 shift lever.

Possibilities are: Bent shift rod; worn shifter; worn shift rod at connection to shift lever on transmission.

Oct 10, 2009 | Ford F-250 Cars & Trucks

1 Answer

Chevrolet Automatic express 2500 gear shifter is broke, what are the parts for the shifter and from shifter to the transmission?


gear shift selector roll pin that holds shift lever in postion shift rod shift rod pivot and spring assembly, colomm retainer assembly pin for shift lever lower and shift linkage lower.

Sep 10, 2009 | 2002 Chevrolet Express

1 Answer

How can I remove gear shift knob on a 2003 Navigator?


it looks like you disconnect the shift cable and remove the center console finish panel with the shifter.


SECTION 501-12: Instrument Panel and Console 2003 Expedition/Navigator Workshop Manual
REMOVAL AND INSTALLATION Floor Console —Front, Navigator Removal and Installation
  1. Apply the parking brake.
  1. Position the front seat forward.
  1. Remove the two front floor console rear bolts.
  1. Position the front seats rearward.
  1. Disconnect the battery. For additional information, refer to Section 414-01 .
  1. Remove the pin-typ retainer and the window control switch panel.
    • Disconnect the electrical connectors.
  1. Move the shift lever to NEUTRAL and position the shift indicator bezel aside.
  1. Remove the screws and the center console finish panel.
    • Disconnect the electrical connectors.
  1. Disconnect the shift cable.
  1. Disconnect the front floor console electrical connectors.
    1. Loosen the electrical connector bolt.
    1. Disconnect the connector.
    1. Disconnect the electrical connector.
  1. Remove the front floor console side finish panel.
    • If equipped, disconnect the electrical connector.
  1. Remove the front floor console front bolts.
  1. Remove the floor console.

Apr 17, 2009 | 2003 Lincoln Navigator

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...