Question about 1992 Nissan Pathfinder

Open Question

Multi switch How to change multiswitch

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change language in mitsubishi multi communication system


1. Press and hold the multi-information meter switch for about 2 seconds or more to switch from the setting mode screen to the menu screen.
Refer to “Changing the function settings (when the ignition switch is “ON”)”.
2. Lightly press the multi-information meter switch to select (language cooperative control).

3. Press and hold the multi-information meter switch to switch in sequence from

3. Press and hold the multi-information meter switch to switch in sequence from A or 1 (language cooperation enabled) ? M, 2 or P (language cooperation disabled) ? A or 1 (language cooperation enabled).

Hope you get your problem fixed :)

May 19, 2016 | 2006 Mitsubishi Outlander

1 Answer

Headlights not working even when pulling out main switch but pull back on multiswitch


Its supposed to do that.
You are using the "pass" option where you flash your bright lights to let someone know you are going to pass.
Depending on the make model and year, the problem could be the headlight switch or even the dimmer switch.

Nov 01, 2015 | Cars & Trucks

1 Answer

Turn signals dont work.but the hazards wirk.on a 04 aztek


the Hazards and blinkers are usually on different circuits. gotta start at the basics work your way through the system. Check your fuse panel, might as well check all your fuses and replace all blown fuses. if you don't find a blown fuse then I would check the bulbs, if they are the same bulds as the Hazards then you know there good. then I would check for power at the Multiswitch ,the multiswitch is the blinker, cruise control, wiper switch usually on the left side of the steering wheel. if you have power at the switch then replace the multiswitch.

Jul 24, 2014 | Cars & Trucks

1 Answer

I need to replace the relay that controls the washer pump . I currently only have power to the rear washer pump . No noise from the pump when actuated from the multi-switch. (New multiswitch/Pump/hoses to...


you might want to make sure the rear nozel is free and clear,you can do this with a needle,fine wire or my favorite a gituar string.
also trying the rear with the feed hose dissconected might help elimate a cloged nozel.
Ill check to see if I might find a wiring dia.
Gary

Oct 28, 2013 | 1998 Ford Explorer

1 Answer

I have a 2004 Chevy Monte Carlo SS. I have all lights except headlights. Day-time running, Hi-beams and fog lights work. I changed the switch and still doesn't work. About 8 months ago I had to change the...


Sounds strange but make sure your low beam bulbs are good [ they have an average life span- they may have both burnt out at the same time ]. This happened to me once in the 1980's with a VW rabbit.

Jan 24, 2011 | 2004 Chevrolet Monte Carlo

1 Answer

Windshield washer tank is full yet doesn't dispense.


test washer pump and multiswitch [windshield washer switch]

Feb 22, 2010 | 2003 Kia Spectra

1 Answer

High beams don't work and odometer doesn't show mileage


well if you hold the multiswitch back do they come on if so the multiswitch is bad and the odometer is it only mileage or is it everything ex.P R N D 2 1 well if those dont show either and its just a blank spot then does the dimmer switch work for everything else if not well dimmer switch may be bad does the rest of the instrament panel light up? if not theres a 20 amp fuse to replace because ur tail-lamps wont work either and it that is not it you probably either have to have the instrument cluster repaired or go to the scrap yard and get one of which is common for buicks of this year

Aug 27, 2009 | 2002 Buick Century

1 Answer

I have a 2000 328i and the wipers work when switched on (both low and high), but i cannot get the washer or intermittent features to work. I have water in the reservoir but i don't hear the pump come on. ...


Sounds like a defective multiswitch on the steering column that is used to turn on wipers, washer, intermittent, etc. If you were only having problems with the washer, I might suspect the washer motor. But the fact that you are also having problems with the intermittent feature, I would suspect the multiswitch. If you can get access to the washer motor, you can test it by putting 12V to the connector to see if the pump will come on. Are your turn signals activated with the same switch as the wipers?

May 06, 2009 | 1997 BMW 328

1 Answer

V40 window not working


Yes it will,swap them out then you will know if the switch is bad.

Aug 02, 2008 | 2004 Volvo V40 Wagon

1 Answer

Need to find where the multiswitch is in the steer column and how to get at it


the "multi " refers to cruise, wipers, signal and hi/low beams. the multi switch is your signal light switch. (they are $500) Can get one at 1aauto.com $118 - just bought one but not in yet

Jun 30, 2008 | 2000 Chevrolet Impala

Not finding what you are looking for?
1992 Nissan Pathfinder Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...