Question about 1991 Chevrolet S-10 Blazer

Open Question

How to replace flywheel in 1997 S10 blazer 4x4

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: 1991 chevy s10 blazer

Check the fuse under the dash. Did you replace the inline fuel filter? If not, you could loosen the line going into the filter then turn the key to the on position. The pump should run for about 2 seconds then the relay should kick off. Turn off the key for approx. 5 seconds then cycle key back on and the pump should cycle again. If you get a 2 second burst of fuel each time then the pump is cycling. Install a new fuel filter and check the grounded wire by the tank. Hope this helps. :)

Posted on Nov 03, 2008

jimbopickens
  • 56 Answers

SOURCE: 98 chevy s10 blazer turn signal

Unplug the turn signal relay from the fuse box and start you engine. Does it still make that noise?
If yes... Put the relay back in, that is not the problem.
If No...Then the relay could be bad, replace it!

PLEASE RATE THIS SOLUTION! Thank You Very Much!

Posted on Nov 25, 2008

tripletauto
  • 1450 Answers

SOURCE: 1984 s10 2.8 manual trans. flywheel causes engine to vibrate

no should be same engine. check your engine mounts and tranny mount. how bad a vibration? sometimes after installing engine the trans gets shifted around and if mount was worn it will allow it to hit crossmeber and vibrate.

Posted on Jan 16, 2009

emissionwiz
  • 75235 Answers

SOURCE: replace thermostat 1994 s10 blazer

follow the upper radiator hose to the engine, under the nipple that the hose attaches to on the engine is the thermostat, 2 bolts and maybe a bracket VERY EASY TO DO.

Posted on Feb 10, 2009

  • 82 Answers

SOURCE: 1999 Chevy S10 Blazer 4x4. Replacing rear pad's,& Bleeding Breaks

have one person in the blazer pumping the brake pedal and then hold to the floor, crack the bleeder then tighten, release pedal, repeat till all air is out one side at a time, if this does not work then your ABS unit is bad witch if u follow your lines from your master cylinder u will find a black box with a motor on it, or the master cylinder itself is bad, it also can cause u to have no pedal, replace the master cylinder first, most likely cheaper.

Posted on Mar 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remover oil pan on 1997 s10 blazer


its a pain in the ****
if its 4x4 you have to drop the front diff
if its 2wd you have to jack up the motor alot
dont crack the dist cap on the back of the motor
on the firewall

Jan 10, 2010 | 1997 Chevrolet Blazer

1 Answer

I have a 1997 S10 Blazer 4X4. After thing warm up


Check your tranny fluid level. Make sure you have enough.

Nov 02, 2009 | 1997 Chevrolet Blazer

1 Answer

Changed engine,starter hitting flywheel


did you put the shims back in the starter?

Apr 22, 2009 | 1986 Chevrolet S-10 Blazer

1 Answer

1999 Chevy S10 Blazer 4x4. Replacing rear pad's,& Bleeding Breaks


have one person in the blazer pumping the brake pedal and then hold to the floor, crack the bleeder then tighten, release pedal, repeat till all air is out one side at a time, if this does not work then your ABS unit is bad witch if u follow your lines from your master cylinder u will find a black box with a motor on it, or the master cylinder itself is bad, it also can cause u to have no pedal, replace the master cylinder first, most likely cheaper.

Mar 11, 2009 | 1997 Chevrolet S-10 Pickup

2 Answers

Replace thermostat 1994 s10 blazer


follow the upper radiator hose to the engine, under the nipple that the hose attaches to on the engine is the thermostat, 2 bolts and maybe a bracket VERY EASY TO DO.

Feb 10, 2009 | 1994 Chevrolet S-10 Blazer

1 Answer

1984 s10 2.8 manual trans. flywheel causes engine to vibrate


no should be same engine. check your engine mounts and tranny mount. how bad a vibration? sometimes after installing engine the trans gets shifted around and if mount was worn it will allow it to hit crossmeber and vibrate.

Jan 16, 2009 | 1984 Chevrolet S-10

Not finding what you are looking for?
1991 Chevrolet S-10 Blazer Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...