Question about Dodge Durango

Open Question

Replacement of blower resistor 2004 dodge durango

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 393 Answers

SOURCE: 2004 Dodge durango-blower not working

the blower is the same for front and rear. you have a blend door problem look by your feet on drivers side just under dash there is a slide mechanism that breaks.

Posted on Dec 09, 2008

  • 2 Answers

SOURCE: how to replace a blower motor resistor in a 2004 jeep liberty

You have to take the glove box off and it is right behind it, need a #20 Torx to take it replace it. The glove box is the hardest part of the job, I just replaced mine on an 05 Grand Cherokee but it didn't fix it for me, was well worth the $8.60 to try though.

Posted on Apr 06, 2009

motor1258
  • 6674 Answers

SOURCE: replace my blower resistor on my 1999 dodge caravan

Under hood up behind strut tower on firewall on passenger side. You'll see a connector attached to a 1-1/2"x 3" rectangular piece that is inserted inside firewall. Pull it to one side then pull out. You may have to play with it a bit, but it will come. Clips in behind it. If you buy the new one first, you'll see the clips that are on other side of firewall in hole.

Posted on Apr 28, 2009

  • 1 Answer

SOURCE: replace durango blower motor resistor

2003 Dodge durango, the blower motor stoppped came back on and stopped again and never came back on. I replaced the blower motor and still no air. Can anyone help?

Posted on Aug 01, 2009

  • 5 Answers

SOURCE: How do you replace blower motor resistor on a 2004

Here is how to change the resistor- but also pay attention-
Did you also change the connector at the same time?
If you are changing the resistor due to overheating and melting of plastic, then you need to do the connector also, or else it will repeat fail in a very short time.

Here is a step-by-step check you can do to fix it. If you are onlygetting high speed (setting 5), then most likely you have a resistorproblem, or the wiring connector to the resistor is bad. The groundwire prong being bad is a possible cause.

Check this for step-by-step checks:

http://www.sparkys-answers.com/2008/07/2005-chevrolet-silverado-blower-inop.html

Posted on Sep 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 dodge durango heater switch hasnt worke on high for a while today stopped working all togethor


It's probably the blower motor resistor. It can overheat and burn out, often melting the connector so the connector cannot be separated. See the linked YouTube video for information on replacing the resistor, and connector if necessary.
Dodge Dakota Durango Blower Motor Resistor Replacement

Feb 04, 2017 | Dodge Cars & Trucks

2 Answers

A//c unit works only on high speed/


blower motor resistor...it cuts power to lower settings...easy fix usually under passenger side glovebox two screws and harness looks like a metal card with plastic bottom...

Jan 28, 2016 | 2004 Dodge Dakota

2 Answers

I have a 2004 dodge Durango. one day the interior fan control stopped working...you have to turn it to 3 to get the fan to cone on..?


Recommend replacing blower resistor card, get a factory one the aftermarket ones dont seem to last as long

Apr 13, 2015 | 2004 Dodge Durango

1 Answer

Blow motor one speed 2004 dodge durango


The blower motor on most models is controlled by the fan switch on the dash and a resistor in the HVAC box. You may find one of the connectors has been unplugged.
I would check for voltage at the resistor on each speed setting.

Jul 25, 2012 | 2004 Dodge Durango

1 Answer

2004 dodge Durango, air will not blow, have checked all the appropriate fuses, replaced resistor, disconnected blower motor and checked it, it works fine....completely out of ideas. When the car is moving...


sounds like you have done all the hard stuff maby its the switch inside [on/off] on the dash that is not working properly.. i hope this helps its the first thing i thought of...

Jun 02, 2011 | 2004 Dodge Durango

1 Answer

Heater blower motor not working for dodge dakota 2004 4x4 4.7 quad cab


try picking up a blower motor resistor, about 10-20 dollars at a local part store. then check this blog out. I have replaced 4 in my 2004 dakota, Takes about 10 minutes to replace, located on passanger side of truck above floor.
http://www.dakota-durango.com/forum/showthread.php?t=65326 WORTH READING AND HAS PICS !

Jan 07, 2011 | 2004 Dodge Dakota

1 Answer

2004 Dodge durango-blower not working


the blower is the same for front and rear. you have a blend door problem look by your feet on drivers side just under dash there is a slide mechanism that breaks.

Nov 11, 2008 | 2002 Dodge Durango

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...