Question about 2000 Toyota 4Runner

Open Question

How do you remove a harmonic balancer in a chevy 3500 with 8.1 2007

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 14585 Answers

SOURCE: I have an 89 Toyota P/U 4cyl. w/air & power steering. I removed my harmonic balancer to repair/replace the front main seal. I replaced a new harmonic balancer and front main seal and a streaming o

Replacing the cam seal. You had to pull the timing belt. Because you had to remove the cam gear. This is where the problem is. Reset the timing and follow the manual to exact procedures. I recommend you replace all the timing components. Also, when you set the timing belt tensioner, Pry on it to get maximum tension. Before you put it together, turn the crank shaft two full turns (by hand/wrench/socket. Make sure it is on the marks. then reassemble.

Posted on Dec 04, 2014

Testimonial: "The "EXPERT" never read my post/question"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How long will it take to replace harmonic balancer?


How-To Remove Crankshaft Harmonic Dampner and Pulley ...

? 7:00
www.youtube.com/watch?v=dXoVVJcm9bs
Feb 8, 2009 - Uploaded by StevexNYCperformance Removal of the Chevy LT1/LT4 Crankshaft Pulley/Dampener. This video Feature AutoZone Harmonic ...

Oct 30, 2015 | 2006 Chevrolet Chevrolet Impala SS

1 Answer

How do I remove a harmonic balancer on a 1966 chevy c10. Also is there a bolt I need to remove first? And is there a key way. So I can make sure it goes back on in the right position?


you will need a harmonic balance pulling tool to remove it, there is a bolt that keeps it fastened to the end of the crankshaft. its in the centre of the balancer and yes there is a key way that locates the balancer on the crankshaft and causes the balancer to turn with the crank without spinning on it.

Mar 11, 2015 | Chevrolet Cars & Trucks

1 Answer

I have an 2006 dodge stratus.im changeing the front crank seal.do I have to pull the engine out to remove the harmonic balancer?


You should be able to get to the harmonic balancer while it's in the car. Remove right tire( use jack stands to hold the car up- not a jack). remove the inner splash guide and the balancer will be exposed. Using 3 jaw puller to remove harmonic balancer

Harmonic balancer removal DodgeForum com

May 31, 2014 | Cars & Trucks

1 Answer

I need the location of the harmonic balancer on my 2.2l Ecotec engine. Car is 2004 Chevrolet Cavalier LS.


CRANKSHAFT PULLEY IS THE HARMONIC BALANCER.YOU NEED THESE TOOLS TO REMOVE HARMONIC BALANCER, YOU NEED HARMONIC BALANCER REMOVER AND INSTALLER TOOL.YOU NEED A LARGE PIN SPANNER WRENCH TO HOLD HARMONIC BALANCER IN PLACE WHILE LOOSEN THE HARMONIC BALANCER BOLT.

May 21, 2011 | Chevrolet Cavalier Cars & Trucks

2 Answers

Location of crankshaft censer 2007 chevy cobalt


The Crank shift sensor is located in front of the motor in between the intake manifold and oil filter housing, nest to the knock sensor. Look on side cylinder block beside starter.you have to remove the starter to remove the crankshaft sensor. Hope this helps. Thanks for choosing Fixya, RJ

May 16, 2011 | 2007 Chevrolet Cobalt Coupe

1 Answer

How do i remove harmonic balancer & replace


YOU NEED A HARMONIC BALANCER PULLER TOOL AND A 15M SIX POINT SOCKET TO REMOVE HARMONIC BALANCER BOLT.TURN OFF RADIO AND REMOVE THE DRIVE BELT AND REMOVE THE NEGATIVE BATTERY CABLE. REMOVE THE STARTER SO YOU CAN PUT A LARGE SCREW DRIVER OR LARGE PUNCH TO STICK IN ONE OF THE FLY WHEEL HOLES TO KEEP ENGINE FROM TURNING WHEN YOU LOOSEN THE HARMONIC BALANCE BOLT. ALSO SCREW DRIVER AND PUNCH CAN KEEP ENGINE FROM TURNING WHEN REMOVER THE HARMONIC BALANCER. YOU WILL NEED A HELPER TO HOLD PUNCH OR SCREW DRIVER WHILE YOU LOOSEN THE BOLT. YOU CAN GO TO SEARS OR ANY AUTO PARTS STORE AND BUY HARMONIC BALANCER PULLER.TORQUE HARMONIC BALANCER BOLT TO 76 FT LBS.

Apr 23, 2011 | 2003 Pontiac Montana

1 Answer

Im tring to find instructions on how to install a harmonic balancer for a 01 chevy impala


If you have a manual, likely you are looking in the wrong place...that would be listed as part of any timing chain removal, front seal removal etc.
Balancer is removed by taking off any pulleys attached to it, removing the center bolt, then using a harmonic balancer puller (specific tool).
To put it back on, just put the new one on the crank snout, put back in the center bolt and washer and tighten it up. (anything that is in your way and preventing you from getting in there needs to be removed as well)

May 30, 2010 | 2001 Chevrolet Impala

1 Answer

How to replace harmonic balancer 1993 2.8L chevy s10 6 cyl


drain radiator and remove, remove all belts, remove outer pulleys from balancer then remove big center bolt from balancer ,make sure you use puller made to remove the balancer you can rent them at your local auto zone 

Mar 07, 2010 | 1993 Chevrolet S-10

2 Answers

Harmonic balancer


what are the steps to removing a harmonic balancers

Oct 18, 2008 | 1997 Chevrolet Corvette

Not finding what you are looking for?
2000 Toyota 4Runner Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...