Question about 1985 BMW 3 Series

Open Question

1985 bmw 325e surging idle - 1985 BMW 3 Series

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

moparownr
  • 667 Answers

SOURCE: procedures for replacing front shocks/struts on 1985 bmw 325e

are you changing the strut cartridge or the whole spring unit? if you are installing the whole unit, spring and all you will need no special tools, if not you will need a spring compressor

Posted on Apr 06, 2009

bitchn65cuda
  • 70 Answers

SOURCE: 1985 bmw 325e

Its your transmission...BMW made bad transmissions up to 1990.

Posted on Apr 19, 2009

  • 280 Answers

SOURCE: I have a 1985 BMW 325E that has a fuel problem.

Sounds like a Temperature sensor is malfunctioning, or maybe the o2 sensor/lambda sensor. get a multimeter and check the sensors around the engine for open circuits.
Its most likely (from exp) that it is a Temp Sensor.
There are two heat sensors, one for drivers information (connected to the dashboard) and one to tell the ECU what settings to run the engine with.
Its not the fuel pump.
That would result in fuel starvation.
This soulnds like the ecu is trying to compensate for a crazy value given by the temp sender.

Posted on Apr 30, 2009

tse22
  • 103 Answers

SOURCE: 1985 BMW 325e power windows don't work. Can anyone

Check your fuses and relays

Posted on May 13, 2009

  • 105 Answers

SOURCE: HOW COULD I READ CHECK ENGINE CODE ON A 1986 BMW 325E???

You can't use a tool to pull codes from an '87 BMW 325(e). You have the 2.7 liter and your DME, or computer is a Motronic. If you had a 325i, then a tool could read the codes because the computer was upgraded that year to a Motronic 1.1 system with a round plug in under the screw cap on the driver's side under the hood. The only tool you can buy is the one for resetting the service interval light and resetting the oil change light. To answer your question about going about finding your driveability problem would be to get a BMW Bentley Manual. This manual shows you how to use a standard voltmeter to check everything from your computer plug in. Your computer is located above the glovebox.

Good Luck,

~Stillin~

Posted on Jun 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bmw instructions


you will need the use of a lift to be able to lift car off the subframe once you have dismantled the wheels, suspension etc , get a work shop manual, that will give you a step by step guide on how to do this , it is pretty complex so i'd really recommend getting the workshop manual

Jun 03, 2014 | 1982 BMW 325e

1 Answer

Cant find the location of obd code reader connector on 1985 bmw 325e


Are you trying to connect a code reader or your phone to your car? You probably mean OBD-II, which didn't come along until several years after 1985.

Apr 30, 2014 | Cars & Trucks

1 Answer

How much would it cost to repair 2 electrical windows on my 325e bmw? 1985


a shop will charge about $250 and above per door just depending the nature of the problem...

Feb 16, 2010 | 1985 BMW 3 Series

1 Answer

Reset ''Service Oil'' sensor on a 1985 BMW 325E off dash console


Call your local BMW dealer and ask them...should be free!
Good Luck

Jun 14, 2009 | 1985 BMW 3 Series

1 Answer

Can a weak battery cause a BMW to misfire?


hello, if the vehicle ran with cable off one would ASUME alternator is ok! however, i bad diode in the aletnator would allow it to charge yet have a massive voltage draw as well, almost all of todays parts stores will do a free starting and charging test for you! ......ps a large voltage drop would rob your ignition of voltage causing your miss!.good luck, marty

Jun 07, 2009 | 1985 BMW 3 Series

1 Answer

I have a 1985 BMW 325E that has a fuel problem. The car surges when at idle. What could be the problem? One fuel pump was replaced last fall, and the car still is running, and you can start it up. It just...


Sounds like a Temperature sensor is malfunctioning, or maybe the o2 sensor/lambda sensor. get a multimeter and check the sensors around the engine for open circuits.
Its most likely (from exp) that it is a Temp Sensor.
There are two heat sensors, one for drivers information (connected to the dashboard) and one to tell the ECU what settings to run the engine with.
Its not the fuel pump.
That would result in fuel starvation.
This soulnds like the ecu is trying to compensate for a crazy value given by the temp sender.

Apr 30, 2009 | BMW 325 Cars & Trucks

1 Answer

1985 bmw 325e


Its your transmission...BMW made bad transmissions up to 1990.

Jul 15, 2008 | 1984 BMW 3 Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...