Question about 2006 Chevrolet Silverado

1 Answer

How do you know which Transfer Case do i have in my 2006 Chevy Silverado -1500

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Chevrolet Master
  • 803 Answers

Look for stamped tag near fill plug

Posted on Feb 11, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

csmock132
  • 4669 Answers

SOURCE: Transfer case leak

You mean between the case halves? It is just silicon, no gasket. These are good for the pump wearing a hole in the rear housing and leaking oil. The cure for it is a new rear housing and a piece called a case saver that keeps the pump from doing it again. Taking the transfer case apart to fix it is easy, I can tell you how to do it.

Posted on Mar 02, 2009

suterman
  • 158 Answers

SOURCE: thermostat location 2001 chevy silverado 1500

The thermostat is in the hose on the passener side of the waterpump.It is in the part that has the three 10mm bolts.Please rate my answer, Thank you.

Posted on Mar 05, 2009

  • 10 Answers

SOURCE: 1996 chevy silverado z71 electronic transfer case wont work

It's the transfer case vacuum switch. Easy fix.

Posted on Jun 17, 2009

robslac24
  • 2 Answers

SOURCE: 01 Chevy Silverado 4 X 4 not working. 4WD light

Having the same exact problem but with my 1999 escalade. Thought it was the actuator bought a new one installed it transfer case would engage but front end wouldnt lock. Took it out of housing left it plugged in got a friend to go through all the 4wd for me and the plunger never moved out the actuator. Checked my wiring harness which is a four prong ann it had one hot prong like it is suppose to. Traced wires even replaced dash switch same problem. Taking it to local dealership tom to have it checked for codes. I was told it could be the transfercase actuator even though its workin that actuator is what sends power to the front to engage the actuator to lock the differential.

Posted on Sep 16, 2009

Molson02536
  • 3854 Answers

SOURCE: 1999 1500 Chevy Silverado - microchip for anti-theft?

Document ID# 803013
1999 Chevrolet Chevy K Silverado - 4WD

Security Lamp Illuminated on the IP, Engine Stalls, No Start, DTC B2960 (Security System Sensor Data Incorrect but Valid) Set (Inspect and Repair Cause of DTC B2960)
1999-2001 Chevrolet and GMC C/K Pickup and Utility Models (Silverado, Sierra, Tahoe, Suburban, Yukon, Yukon XL)

This bulletin is being revised to add information on inspecting for electrical intermittent conditions and important connector C201 tightening steps. Please discard Corporate Bulletin Number 01-08-56-002 (Section 08 -- Body and Accessories).

Condition
Some customers may comment on the following conditions. These symptoms may be intermittent.

• Security lamp illuminates while driving. The Security lamp may be On or Off when the customer brings the vehicle to the service facility.

• The engine cranks but will not start and the Security lamp is flashing.

• The engine starts then stalls and the Security lamp is flashing.

Cause
Condition(s) may be due to an incorrect Passlock™ sensor voltage received by the body control module (BCM) from the Passlock™ sensor due to the following conditions. Most intermittent conditions are caused by faulty electrical connections or wiring.

• A 7 ohm variation in the sensor ground circuit wiring, circuit 1057

• A 100 ohm variation in the Passlock™ sensor signal wiring circuit, circuit 1836

Inspect for the following items:

• Broken wiring inside the insulation.

• A poor connection between the male and female terminal at the connector. Refer to Testing for Proper Terminal Contact under Testing for Intermittent and Poor Connections in Wiring Systems for the specific procedure.

• A poor terminal to wire connection. Some conditions that fall under this description include poor crimps, poor solder joints, crimping over the wire insulation instead of the wire itself, and corrosion in the wire to terminal contact area.

• Wire insulation that is rubbed through. This causes an intermittent short as the bare area touches other wiring or parts of the vehicle.

• A poor connection between the male and female terminal at a connector. This poor connection may be the result of contamination or deformation.

- Contamination may be caused by the connector halves being improperly connected. A missing or damaged connector seal, damage to the connector itself, or exposing the terminals to moisture and dirt can also cause contamination. Contamination, usually in the underhood or underbody connectors, leads to terminal corrosion, causing an open circuit or intermittently open circuit.

• Separate the connector halves.

• Visually inspect the connector halves for contamination. Contamination may result in a white or green build-up within the connector body or between terminals. This causes high terminal resistance, intermittent contact, or an open circuit. An underhood or underbody connector that shows signs of contamination should be replaced in its entirety including the terminals, the seals, and the connector body.

- Deformation is caused by probing the mating side of a connector terminal without the proper adapter, improperly joining the connector halves, or repeatedly separating and joining the connector halves. Deformation, usually to the female terminal connector tang, can result in poor terminal contact causing an open or intermittently open circuit. Using an equivalent male terminal from the J 38125-B, test that the retention force is significantly different between an good terminal and a suspect terminal. Replace the female terminal in question.

Correction
Have any of the following components had service recently?

• The BCM

• The ignition lock cylinder case assembly

• The PCM/VCM

If any of the above components have been replaced, the Programming Theft Deterrent System Components procedure must be performed before any diagnostic procedures are performed.

To assist in diagnosis, the following steps are provided.

Does the engine start? If not, use the Engine Cranks but Does Not Run diagnostic information in the Engine Controls sub-section of the applicable Service Manual.
Important:

• The Security telltale on the message center is controlled by the vehicle theft deterrent (VTD) system and the content theft deterrent (CTD) system. The Security telltale is controlled by the BCM through the Class 2 data line.

• The VTD system portion of the BCM controls the Security telltale when the ignition switch is in the On position. The VTD system uses the Security telltale as a malfunction indicator.

• The CTD system portion of the BCM controls the Security telltale when the ignition switch is in the Off position. The CTD system uses the Security telltale to identify system status.


Observe the Security indicator lamp in the instrument panel.
Remove the key from the lock cylinder.
- Security indicator should be Flashing when the door is open.

- Security indicator should be Off when all the doors are closed.

- If the Security indicator does not come On or go Off correctly, refer to the Content Theft Deterrent System diagnostic and repair information in the applicable Service Manual.

With the Doors closed, place the key in the lock cylinder and turn to the Run position. Observe the Security indicator lamp.
- Lamp is On and does not go Off however, the engine starts. This indicates that the VTD system detected a fault when the engine was running.

- Lamp flashes On and Off. This indicates a problem has been detected by the VTD (Passlock™) system and the engine may not start this key cycle, a current condition.

Important: You must diagnose the diagnostic trouble codes (DTCs) in the order specified in the DTC table shown below. Failure to do so may result in one or more of the following conditions:


• Extended diagnostic time

• Incorrect diagnosis

• Incorrect parts replacement


DTC
Diagnostic Procedure
Module

Important: Before you use this table, diagnose P0601, P0602, P0604, and P0606. Refer to Diagnostic System Check - Theft Deterrent.

PXXXX Other PCM DTCs

Refer to the following procedures:

• Diagnostic System Check - Engine Controls in Engine Controls - 4.3L

• Diagnostic System Check - Engine Controls in Engine Controls - 4.8L, 5.3L, 6.0

• DTC P0192 in Engine Controls - 6.6L

• Diagnostic System Check - Engine Controls in Engine Controls - 8.1L


If none of the above items are true, proceed with the following steps:

Install seat covers.
Connect the scan tool to the diagnostic link connector (DLC).
Enter scan tool diagnostics.
Select the model year of the vehicle.
Select light truck.
Select F1, (Body).
Select "C" or "K" for Series.
Select F0, Body Control Module.
Select F0, (Diagnostic Trouble Codes (DTC)).
Select F0, (DTC information).
Select F0, (Current DTC).
Record on the repair order any current DTCs displayed. If none, skip the next step.
Is a current B2960 DTC displayed? If no, the condition is not present with this key cycle. Continue to the next step.
Select Exit.
Select F1, (History DTC).
Are any history DTCs other than B2960 present? If so, diagnose those DTCs first using the appropriate service information, otherwise continue.
Select Exit.
Select Exit.
Select F1, Data Display.
Select F6, Security.
Cycle the key to the OFF position and wait 20 seconds.
Slowly turn the key to the RUN position. Be careful not to turn the key into the START position.
Observe the following values:
- Passlock™ Data Voltage should be 5.0 volts.

- Passlock™ State should be Normal.

- Passlock™ Code should be Open.

Rotate the key to the START position, and observe the following again:
- Passlock™ Data Voltage should be less than 5.0 volts. Passlock™ Data Voltage should remain steady and not fluctuate. The test vehicle used for this diagnostic procedure had a voltage value of 2.49 volts. The vehicle being worked on may be either higher or lower than this value. The key is that it has to be less than 5.0 volts.

- Passlock™ State should be "Monitor Passlock™".

- Passlock™ Code should be Valid Code.

If no trouble is found and the customer has experienced one of the symptoms or the code is a history DTC, the most likely cause is the VTD (Passlock™) wiring, specifically the wires from the VTD (Passlock™) sensor to the BCM.

Posted on May 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will a transfer case from a 94 GMC Sierra 1500 interchange with a 97 Chevy silverado 1500?


As long as it's a manual floor shift transfer case and both transmissions are the same then yes it will fit directly with no problems.

Feb 20, 2015 | GMC Cars & Trucks

2 Answers

Transfer case keeps blowing gaskets


I need a bit more information I take it this a 4x4 cause when you talk about transfer case it means 4x4 and am I to understand you replaced the transmission and transfer case and tail shaft?

Jan 16, 2013 | 1999 Chevrolet Silverado 1500

1 Answer

I have a 1999 chevy silverado Z71 1500 5.3. It makes loud grinding and poping noises when I put it in gear how do I know if its the transmission or the transfer case?


the transfer case only engages when in 4wd. check the universal joint, it connects from the drive shaft to the rear differential. it may need grease or to be replaced.

Aug 08, 2012 | 1999 Chevrolet Silverado 1500

1 Answer

How do I tell what model transfer case I have in a 2004 Chevy Silverado 1500?


i do not know but give these guys a call they only sells GM-parts its Schram auto & truck parts 1-800-292-1032 and they website is www.schramauto.com Merry Christmas & Happy New Year as always wish you the best of luck Michigan Man

Dec 22, 2009 | 2004 Chevrolet Silverado 1500 Crew Cab

4 Answers

Fluid in a transfer case


if it is an electric shift t-case gm has there own oil not found at auto part stores

Sep 18, 2009 | 2003 Chevrolet Silverado 1500

1 Answer

2003 Chevy Silverado Transfer Case


well make sure it is the tranfercase because if it was u wouldent have 4wd and u wouldent be able to drive it but it would be cheper to rebuild it but make sure first because some people are just out for your money good luck

Feb 02, 2009 | 2003 Chevrolet Silverado 3500

2 Answers

2003 Chevy Silverado


i would check both ways first and see what the mechanical rate is in your area take it to a auto body dealership to have it done cahrges are 85.00 to 110.00at the dealership or private shops ok Please rate my response thank you very much

Feb 02, 2009 | 2003 Chevrolet Silverado 3500

Not finding what you are looking for?
2006 Chevrolet Silverado Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...