Question about 2005 Nissan Maxima

1 Answer

Labor to replace engine - 2005 Nissan Maxima

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Nissan Master
  • 14,337 Answers

1200.00

Posted on Feb 11, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cost replace starte 99 chrysler concord


It really depends on where the work is being done because labor rates are different at each shop. I can tell you that in my labor guide it says it takes 2 hour to replace the starter so depending on the shop you take it to would/should be 2 hour in labor. The Concorde came with a 2.7 and a 3.2 liter engine but the labor time is the same. Now as far as the cost of the starter both engines have a list price of about $300.00 but if you were to purchase the part (if the shop lets you) it mast likely would be about half that cost for the parts. Hope I was able to help

May 07, 2012 | 1999 Chrysler Concorde

1 Answer

Service engine light pulls code to replace EGR valve, replaced part and car still runs the same and engine light is still on


the code would run if another error before it is faulty , labors indicates ignition fault , or timing problem , I once had cogs missing on distributer ,

Mar 22, 2012 | 2001 Ford Mustang

1 Answer

How Labor intensive is it to replace the drivers side lower control arm? I had a shop tell me that the engine has to be removed, and 15 hours of labor are involved


I what to make sure this is correct, this is a 2004 lexus rx 330 and the shop said it was 15 hours to replace the lower control arm. This sounds crazy but it is ture, the engine and trans must be removed to replace the lower control arm, i would replace them both as the labor is only 1/2 hour more to do both,and it inculde an alignment in that time also. its a dumb design. hope this helps good day.

Nov 28, 2011 | 2004 Lexus RX 330

1 Answer

How Long to replace a power steering pressure hose? Labor cost?


6 cylinder engine remove and replace pressure power steering hose.

2.2 hrs X there shop labor rate = your labor cost.

Pre Mitchell labor guide

Jun 11, 2010 | 1992 Oldsmobile Cutlass Supreme

1 Answer

I am planning to buy 2000 audi A4 with 95000 miles on it? What do I need to check on this car before I drive off the lot?


This info is from MSN autos.

Occasional problems on this vehicle, 4-cylinder engines only, are failures of the Engine, Engine Vacuum Hoses and the Mass Air Flow (MAF) Sensor. Failure of the Engine is caused because the engine oil gels. When proper maintenance schedules for oil changes are followed, oil gelling should not occur. Audi has issued an 8 year unlimited mileage goodwill repair for this condition. The cost to replace the MAF Sensor is estimated at $380.00 for parts and $60.00 for labor. The cost to repair the Engine Vacuum Hoses is estimated at $25.00 for parts and $65.00 for labor. The cost to repair the Engine is estimated at $4,775.00 for parts and $845.00 for labor. The cost to replace the Mass Air Flow Sensor is estimated at $500.00 for parts and $52.00 for labor. All prices are estimates based on $65.00 per flat rate hour and do not include diagnostic time or any applicable sales tax.

Occasional problems on this vehicle are failure of the Comfort Control Module, with 4-cylinder engines only, and failure of the 4-Way Hazard Flasher. The cost to repair the Comfort Control Module is estimated at $290.00 for parts and $65.00 for labor. The cost to replace the 4-Way Hazard Flasher is $31.50 for parts and $91.00 for labor. All prices are estimates based on $65.00 per flat rate hour and do not include diagnostic time or any applicable sales tax.

Apr 06, 2010 | 2000 Audi A4

1 Answer

89 Dodge Raider 3.0 Labor hours to replace Valve cover Gaskets and seals


.5 for the 4 cyl. and its 3.6 for the 6 cyl. engine. This is according to the Chilton Labor Guide.

Nov 10, 2008 | 1989 Dodge Raider

1 Answer

Labor time to replace 3.3 engine


ive relpaced one of those motors in about 6 hrs with the right tools and in a garage..

Sep 30, 2008 | 1993 Geo Tracker

Not finding what you are looking for?
2005 Nissan Maxima Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...