Question about 1993 Oldsmobile Cutlass Ciera

Open Question

Fuel injectors removel 350c.i. engine 1991 chevy

1/2 ton 4x4

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do you pull a 1979 gmc jimmy 4x4 rear right axle


QU40221 19 Spline Outer Axle Shaft for 1977 to 1991 Chevy, GMC Corporate GM 10 Bolt Front Axle is a genuine original equipment outer axle stub shaft for all GM 10 Bolt front axles in 1977 to 1991 Chevy Blazers, GMC Jimmys, and Suburbans, plus Chevy, GMC 4x4 1/2 ton and 3/4 ton Pickups. The splined end on these new axle shafts has three snap ring grooves in three places so they are compatible with all types of automatic and manual lockout hubs plus all full-time solid splined drive gears.

Also available while supplies last: QU40221U Used Outer Axle Shaft with 3 snap ring grooves and QU40660UUsed Inner Axle Shafts with 2 snap ring grooves (QU40660U is not compatible with automatic locking hubs)



see this vdio

Apr 01, 2015 | GMC Jimmy Cars & Trucks

1 Answer

Removel of injectors 1991 chevy 350 c.i. pick up


This repair is not that bad. ***NOTE: don't disassemble the TBI unit until you have purchased a new TBI gasket. The gasket is paper and when you remove the screws and pull the top half away, the gasket will tear.*** Remove the air cleaner housing and you will see the T.B.I. unit. Unplug both injectors, remove the torque head screws, and carefully pull the top have of the injector housing away. You now can remove the injectors. Just in case you don't know. If the fuel pressure regulator is original, this would be the time to replace it. I hope this helps, let me know how it went.

Feb 11, 2014 | Cars & Trucks

1 Answer

Need a diagram of 1999 chevy 1/2 ton 4x4 rear brake brackets


Go to you nearest auto part. Store. They will print one up for you or when you get the kit it will diagram with it

Mar 06, 2013 | 1994 Chevrolet K1500

1 Answer

1990 3/4 ton chevy 4x4 wont engage


the accuator is proby weak and working under pressure!!!!!

Jan 15, 2010 | 1991 Chevrolet K2500

1 Answer

Chevy express wont start


Will it run for a short time if you squirt some fuel into the throttle body? If so, then concentrate on the fuel delivery system. Fuel pressure at the test port on the fuel rail should be at least 40 PSI. If not, look at the fuel pump, the pressure regulator, and the fuel filter.

Dec 18, 2009 | 1999 Chevrolet Express

1 Answer

1991 chevy 4x4 2500, we changed the distributor,


Timing chain and gears may need replacing. Is the timing correct? Like number 1 at top of compression stroke and the dist. is on 1. How about a new coil too. Try a coil first. They go bad on these a lot.

Jul 12, 2009 | 1991 Chevrolet C/K 2500

1 Answer

4x4 fuse on 1991 chev 1/2 ton keeps blowing..Why?


You might have a short in your wiring some where from the actuator back to where the wires go through the cab .could have been rubbing on something to cause this . just a thought

Jan 13, 2009 | 1991 Chevrolet C/K 2500

1 Answer

1991 Chevy Transmission won't go into O/D


from what i remember the overdrive is electronically activated. it is disengaged by low rpm or a switch on the brake pedal. check the pedal switch and look to see if there is a disconnected wire near transmission.hope this helps. please rate me

Jan 12, 2009 | 1992 Dodge Dakota

Not finding what you are looking for?
1993 Oldsmobile Cutlass Ciera Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

77544 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8826 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...