Question about 2006 Ford E-250

Open Question

DTC Error Code: (0)

Received the above code

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Bought car at auction- no keys. Had key made at GM dealer. Programmed key- key works. Car wont start- Codes are P0633 and P1629. cannot clear codes


DTC P0633 : Theft Deterrent Key Not Programmed

When learning the pre-release password, as well as the challenge and response sequence, the engine control module (ECM) is placed in learn mode. DTC P0633 will set automatically as an indicator that the system is in learn mode and not as a fault indicator. Once the password and challenge/response are learned, learn mode will be exited when the engine is successfully started. At this point, the DTC will be cleared. If the ECM does not exit learn mode, P0633 will remain current and indicate a fault.
The "key" referenced in the DTC descriptor does not refer to the vehicle key. In this case, "key" is referring to the challenge response.
DTC P0633 requires a successful engine start to exit the learn procedure and clear the DTC. If an unrelated malfunction exists that causes engine starting to be disabled or otherwise unavailable, learn mode will not exit and DTC P0633 will remain current. In this situation, the cause of the inoperative engine starting must be corrected before diagnosing DTC P0633.
DTC P1629: Theft Deterrent Fuel Enable Signal Not Received
The theft deterrent module (TDM) sends the pre-release password to the engine control module (ECM) via the serial data circuit. The ECM then sends a challenge to the TDM. Both the ECM and TDM perform a calculation on this challenge. If the calculated response from the TDM equals the calculation performed by the ECM, the ECM will allow vehicle starting.
DTC P1629 is an indicator that the challenge response was not received within the required 2 second window. This does not necessarily indicate a fault is present with the TDM or ECM. Factors such as a long engine crank, a delay in the serial data communication, or B-codes set in the TDM will cause DTC P1629 to set. This DTC should not be used as a fault indicator, but rather as a symptom to assist in the diagnosis of these other systems.
Who checked the codes , you -dealer ? You need to have BCM checked for codes B - codes ! you need a up scale diagnostic scan tool for that , dealer Tech -2 !
DTC B3935 57 : Transponder Authentication Error
DTC B3976 46 : Unconfigured Transponder/Vehicle Configuration Not Programmed
DTC B3060 : Unprogrammed Transponder Identification Code Received
DTC B3055: No Transponder Modulation or No Transponder
DTC B3031: Security System Controller In Learn Mode

Aug 07, 2015 | 2006 Buick Lucerne

Tip

GM OBD1 Codes


DTC - 12 No distributor reference pulse (diagnostic test active)

DTC - 13 Oxygen sensor circuit open or no activity

DTC - 13 Left bank O2 sensor circuit open or no activity

DTC - 14 Engine coolant temp sensor error (high temp indicated)

DTC - 15 Engine coolant temp sensor error (low temp indicated)

DTC - 16 System voltage too low

DTC - 17 Camshaft position sensor error

DTC - 21 Throttle Position sensor error (signal high)

DTC - 22 Throttle position sensor error (signal low)

DTC - 23 Intake air temp sensor error (low temp indicated)

DTC - 24 Vehicle speed sensor error (open circuit or no activity)

DTC - 25 Intake air temp sensor error (high temp indicated)

DTC - 26 Quad Driver Module (QDM A) error

DTC - 28 Auto transmission range pressure switch error

DTC - 31 Wastegate solenoid circuit error

DTC - 31 Gear Position Switch (PRNDL) error

DTC - 32 EGR system failure

DTC - 33 MAP sensor circuit error (signal high indicating low vacuum)

DTC - 34 MAP sensor circuit error (signal low indicating high vacuum)

DTC - 35 IAC problem or idle error

DTC - 36 MAF sensor error

DTC - 36 24x Crankshaft position sensor circuit error

DTC - 36 4T60-E Shifting Error

DTC - 37 TCC brake switch circuit error

DTC - 38 TCC brake switch circuit error

DTC - 39 Clutch switch circuit error

DTC - 39 TCC error

on Sep 10, 2011 | 1991 GMC Sonoma

1 Answer

Two new error codes have shown up, P1189 & C1222. The C1214 error code has been cleared but the C1233 is still showing. What do the new codes mean?


P1189 Oldsmobile: Engine Oil Pressure (EOP) Switch Circuit

C1222 Oldsmobile: Right Front Wheel Speed Sensor Input Signal is 0

C1233Oldsmobile: Right Front Wheel Speed Circuit Open or Shorteduse this, http://www.aboutautomobile.com/DTC/C1214

Jun 08, 2015 | 2002 Oldsmobile Alero

2 Answers

Falt code p0819


needs computer reset

Mar 01, 2015 | 1999 Jeep Grand Cherokee

1 Answer

I have a 1998 chevy silverado check engine code 1345a what does this mean


Do you mean Diagnostic Test Code (DTC) P1345 ?This DTC is a "Manufacturer Specific" code that is defined by GM as "Camshaft/Crankshaft Correlation Error".

It is basically telling you that your Cam/Crank timing is not within specifications.

Possible causes are:

> Improperly installed distributor assembly
> Badly worn distributor shaft or bushings
> Worn timing components (chain, gears, etc.)

Proper diagnosis is required to diagnose the actual condition that is causing this code. If any timing components are replaced, a scan tool capable of reading live computer data is required to check the cam/crank offset PID and make adjustments as necessary.

The specification for Cam/Crank offset is (Zero) 0 +/- 2 and must be checked with the engine running at 1500 RPM.

Jun 03, 2012 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

O/d light blinks when driveing o/d seems to be engaged car has 198000 miles and runs very good also engine light is on


O/D light blinks, but with that the check engine light is ON.--- This will make your troubleshooting easier.When the check engine light comes on, and remains on, this indicates that there is error stored in your cars computer.---- Once the computer is scanned, you will get error codes, as per that error code it will point towards faulty part, which is causing the O/D light to blink.-------- Most probably the O/D light blinks, If a problem exists in No. 1 or No. 2 solenoids or speed sensors .
--------------- For car after 1995 it requires OBD2 tool and for car before 1995 it requires OBD1 tool.------- --------- You car will require OBD1 tool.There are very few auto parts store and repair centers who have OBD1 tool.In your case you required OBD1 tool.------ You can just contact local auto-parts store and they will guide you to the nearest store who has OBD1 tool.There you can get your car scanned.If there is error set in your cars computer, then you will receive the error code.As per error code it will point towards the faulty part causing this problem in your car.------------- -------------- The codes which you get is scanning will be mostly any of this following codes:--- DTC P0500 - Vehicle Speed Sensor Malfunction
. DTC P0750 - Shift Solenoid "A" Malfunction
. DTC P0753 - Shift Solenoid "A" Electrical Malfunction
. DTC P0755 - Shift Solenoid "B" Malfunction
. DTC P0758 - Shift Solenoid "B" Electrical Malfunction
. DTC P0770 - Shift Solenoid "E" (SL) Malfunction
. DTC P0773 - Shift Solenoid "E" (SL) Electrical Malfunction
. DTC P1520 - Stop Light Switch Signal Malfunction
. DTC P1705 - Direct Clutch Speed Sensor Circuit Malfunction
. DTC P1765 - Shift Solenoid Valve SLN Circuit Malfunction
. DTC P1780 - Park/Neutral Position Switch Malfunction
--------------- Now it all depends on what code you get, as per that you can replace the following part.------- This will help.Thanks.Helpmech.

Jul 07, 2011 | 1995 Toyota Camry

1 Answer

Code error U1300 scanner


This code pertains to communication from one computer to the next,they all are on a communication circuit (class II) & you have a short to ground somewhere.If a scan tool is able to communicate with the computer(and it is since you got a failure code) this code is intermitten.Get a good volt meter or scan tool & start at the ALDL (where the scanner plugs in).Inspect & check wiring as you keep an eye on the scanner or meter.

DTC Parameters
DTC U1300 will set if the EBTCM, PCM, or SDM detected the Class II circuit in the low state for too long. (Class II circuit shorted to ground) when:
• Condition exists for longer than 4 seconds for EBTCM, 2 seconds for PCM and SDM.
• Ignition is On.

DTC U1300 diagnostic runs continuously with ignition On.

DTC U1300 is a type C DTC.
Diagnostic Aids
If the scan tool can communicate with the EBTCM, PCM or SDM, then the Class II link is not currently shorted to ground.

Inspect the wiring harness for signs of chafing or broken insulation.

Important: The controller name won't be displayed until the scan tool initially received the correct controller ID over the link upon ignition On.

Important: The BCM CANNOT set U1300.

To locate an intermittent problem, use the scan tool to monitor any of the controllers on the Class II link located under DIAGNOSTIC CIRCUIT CHECK - - - CLASS II MESSAGE MONITOR with ignition On, engine Off. INACTIVE will be displayed on all controllers if the link is shorted to ground.


Hope this helps (remember to rate this answer).

Jan 14, 2011 | Chevrolet Impala Cars & Trucks

2 Answers

I received a P1154 OBD code error. It says


DTC P0131 or P0151
Circuit Description
Heated oxygen sensors (HO2S) are used for fuel control and post catalyst monitoring. Each HO2S compares the oxygen content of the surrounding air with the oxygen content in the exhaust stream. The HO2S must reach operating temperature to provide an accurate voltage signal. Heating elements inside the HO2S minimize the time required for the sensors to reach operating temperature. The powertrain control module (PCM) supplies the HO2S with a reference, or bias, voltage of about 450 mV. When the engine is first started, the PCM operates in Open Loop, ignoring the HO2S voltage signal. Once the HO2S reaches operating temperature and Closed Loop is achieved, the HO2S generates a voltage within a range of 0-1,000 mV that fluctuates above and below bias voltage. High HO2S voltage indicates a rich exhaust stream. Low HO2S voltage indicates a lean exhaust stream. If the PCM detects an HO2S voltage that stays below a specified value, DTC P0131 sets for HO2S bank 1 sensor 1, or DTC P0151 sets for HO2S bank 2 sensor 1.

Oct 06, 2009 | 2001 Hyundai Santa Fe

1 Answer

Error codes


P0523 means the Oil pressure voltage to high. Your Oil pressure sensor may need to be replaced. P1682 means your charging system is to low. Your voltage regulator may be going bad or the whole alternator. p1693 means a Diagnostic trouble code (DTC) has been detected in the ECM or PCM which is related to the above DTC P0XXX codes. Good luck and hope this helps. Keep me posted, be glad to help

Jun 11, 2009 | 1999 Dodge Ram

Not finding what you are looking for?
2006 Ford E-250 Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...