Question about Ford Fusion

Open Question

P0608 error code - Fusion Ford Cars & Trucks

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

A 2001 jimmy gmc my speedometer dose not work and my transmision will not shift i changed the sensor and it didnt fix the problem i changed the filter didnt help what else could cause this problem


What sensor did you change . VSS - vehicle speed sensor or output speed sensor .
The ideal what to find the problem would be to hook up a factory scan tool to see the VSS is put out a signal to the PCM/ECM , then see if the PCM /ECM is sending info to the instrument cluster ,. And knowing how these this work couldn't hurt either .

The IPC displays the vehicle speed based on the information from the PCM. The PCM converts the data from the vehicle speed sensor to a 4000 pulses/mile signal. The IPC uses the vehicle speed signal circuit from the PCM in order to calculate the vehicle speed. The speedometer defaults to 0 km/h (0 mph) if a malfunction in the vehicle speed signal circuit exists.

Have the vehicle checked for DTC"S - diagnostic trouble codes . No all code's turn on the check engine light .
DTC P0608
The PCM creates the vehicle speed output signal by pulsing the circuit to ground. The PCM pulses the circuit at the same rate as the vehicle speed signal input. The PCM monitors the voltage on the vehicle speed signal circuit. If the PCM determines the voltage is out of the normal operating range, a DTC sets.

Install a scan tool.
Raise the vehicle's drive wheels. Refer to Lifting and Jacking the Vehicle in General Information.
Start the engine.
Place the transmission into drive for an automatic transmission or third gear for a manual transmission.
With the scan tool, observe the Vehicle Speed Sensor parameter in the PCM data list.
Does the Vehicle Speed Sensor parameter match the speedometer display?

This is something best taken to a qualified repair shop . This could be a wiring issue , or the PCM or the instrument cluster .

Feb 14, 2017 | GMC Jimmy Cars & Trucks

2 Answers

Why is code 91 on screen?


About 1,080,000 results (0.79 seconds) Search Results

    Chevy Cruze error code 91 - Fixya

    www.fixya.com/cars/t18378173-chevy_cruze_error_code_91
    Jun 2, 2013 - Chevy Cruze error code 91 What is Error code 91? It appeared ... Ya i know that what is error code 91 it is that ur car key is not there & if shows error code35 then ur car remote key cell losing his power exchange with that cell & ur car is ok. Posted on ... SOURCE: chevrolet cruze 2.0 LT 163cv error. If im not ...

    Warning: Cruze Start/Stop button & Immobiliser Design Flaw ...

    gearheads.in > Forum > Indian Automotive Scene > Chevrolet > Cruze

    Apr 16, 2013 - 10 posts - ‎7 authors
    4kms later I realised that I had the Cruze key with me in my pocket ... If the key is outside the car and you try to start it, it throws a Code 91 Error ...

    Cruze error code ' Chevy Cruze Blog : Chevrolet Cruze Blog

    www.cruzeblog.com/cruze-error-code/

    Translate this page Mar 7, 2014 - Cruze Error Code Vehicle message 1 C

Feb 09, 2016 | Chevrolet Cruze Cars & Trucks

1 Answer

Check engine light is on and diagnatics show the error codes, P0722 and U2108


Definition of Diagnostic Trouble Code U2108 Buick: CAN Bus Error ABS Cadillac: CAN Bus Error ABS Chevrolet: CAN Bus Error ABS GMC: CAN Bus Error ABS Oldsmobile: CAN Bus Error ABS Pontiac: CAN Bus Error ABS Saturn: CAN Bus Error ABS


Definition of Diagnostic Trouble Code P0722 Category: Powertrain Definition: Output Speed Sensor Circuit No SignalNote: This definition of P0722 is applied to all manufacturers

Jun 27, 2015 | Cars & Trucks

1 Answer

Loss of communication with the tcm and pcm


The onboard computer, or Powertrain Control Module (PCM),is the brains of the engine control system, so when the brain is not functioning correctly neither is the engine or anything else that the microprocessor controls - which may include the charging system, transmission, various emission controls and communications with other onboard control modules. Once a diagnosis has been made (and we emphasize the word diagnosis), then and only then should the PCM be replaced.
P0600....Serial Communication Link

P0601....Internal Control Module Memory Check Sum Error

P0602....Control Module Programming Error

P0603....Internal Control Module Keep Alive Memory (KAM) Error

P0604....Internal Control Module Random Access Memory (RAM) Error

P0605....Internal Control Module Read Only Memory (ROM) Error

P0606....ECM/PCM Processor

P0607....Control Module Performance

P0608....Control Module VSS Output 'A'

P0609....Control Module VSS Output 'B'

P0610....Control Module Vehicle Options Error

If you see any of these codes when diagnosing the vehicle with a code reader or scan tool, it may mean the PCM has failed and must be replaced. Additional diagnostic tests will usually be necessary to confirm the problem is really the powertrain control module and NOT something else. Refer to the OEM diagnostic charts for what these tests are. Usually it involves checking certain inputs to the PCM to see if it outputs the correct response. No response or an incorrect response usually means the PCM is defective and needs to be replaced.
All too often, technicians tend to blame that which they understand least. If an engine is not running right and the cause is not obvious, they may blame the computer. Throwing parts at a problem in an attempt to solve it may be good for the parts business, but when a customer brings a PCM back because it failed to fix their problem, nobody wins. Warranty returns on complicated and expensive components like powertrain control modules are an ongoing problem that costs everyone money.
UNNECESSARY POWERTRAIN CONTROL MODULE RETURNS. Over 50 percent of PCMs that are returned under warranty (either because the PCM failed to fix a performance problem or because the engine did not run properly after it was installed) have nothing wrong with them! So it is obvious a lot of people are swapping computers to see if a different PCM will fix their problem.
The trouble with returns is if the PCM has been on the car, you have no way of knowing if it is still "good" or not. Somebody may have crossed up some wires, zapped the PCM with too much voltage or who knows what? The computer needs to be tested and verified before it can go back on the shelf and be sold to somebody else.
Unfortunately, there is no easy way of doing that in a parts store. The PCM has to be hooked up to a sophisticated simulator that exercises all of the computer's input and output circuits to make sure it works correctly - which means the PCM has to go back to the supplier, be retested, and if no fault is found, repackaged and put back into stock.
Be warned, though, that many parts stores have a policy of "no returns or refunds on electronic components."

Mar 20, 2014 | 2005 Lincoln Navigator

1 Answer

I have a 2003 Ford Explorer the o/d light is blinking. I had diagnosis tested ran and came up with PO73 invorrect gear 3 ratio, PO745 Pressure control solenoid malfunction and PO745 Pressure control...


Error Code P0745
  • If the error code checker returns a P0745 code, it is indicative of a transmission issue. Error codes in the 700s refer to transmission problems. The P0745 error code refers specifically to a malfunctioning pressure control solenoid. This should be checked by a mechanic as soon as possible.


  • Read more: Ford 2002 Explorer Error Codes ' eHow.com http://www.ehow.com/list_7610006_ford-2002-explorer-error-codes.html#ixzz1FCgt5JQ6

    Feb 27, 2011 | 2003 Ford Explorer

    1 Answer

    Recently my check engine light came on and I did a diagnostic to find a P0607 error to appear. The code had read something about a power train control module. I will probably end up taking my car into the...


    P0601 Internal Control Module Memory Check Sum Error
    P0602 Control Module Programming Error
    P0603 Internal Control Module Keep Alive Memory (KAM) Error
    P0604 Internal Control Module Random Access Memory (RAM) Error
    P0605 Internal Control Module Read Only Memory (ROM) Error
    P0606 ECM/PCM Processor
    P0607 Control Module Performance
    P0608 Control Module VSS Output "A"
    P0609 Control Module VSS Output "B"
    P0610 Control Module Vehicle Options Error
    The p0607 error says Control Module Performance. It has something to do with the Control Module for the powertrain as you indicated. But, you may be able to take your car to a transmission shop to alleviate the problem using a transmission expert.

    I don't think that it doesn't have anything to do with the engine, itself, even though it's listed under a driveability related code.

    Good luck on this repair.

    Jan 14, 2011 | 2002 Dodge Stratus

    4 Answers

    P0601 diagnostic code what is the mean , or whats is the problem


    P0601 - Internal Control Module Memory Check Sum Error

    Basically that means that there is an interal fault in the Powertrain Control Module (PCM). There have been many reported PCM failures on Chrysler/Dodge products although it is possible for this to happen on any vehicle. In Dodge/Chrysler products, a P0601 trouble code means that a serial communication failed inside the computer at least 6 times.

    Symptoms: Likely, no symptoms will be discernible to the driver, other than the illuminated Check Engine Light. Typically the engine runs fine, gauges work, etc.

    Causes: A code P0601 in most cases means the PCM has gone bad. This is possibly due to a short-circuit inside the PCM. Or, if you disconnect the wires/connector from the PCM while the battery is still connected, that may also cause this code.

    Possible Solutions: With a P0601 OBD-II trouble code, the most common fix is to replace and reprogram the PCM. In a few cases the dealer may be able to reflash the PCM and get it working. But more than likely the PCM will need to be replaced and reprogrammed (we recommend you take it to a dealership for this). The good news is it *may* be covered under your emmissions warranty. So even if you're out of bumper-to-bumper warranty or powertrain warranty, check your warranty guide or dealer to see if this is covered.

    Other people have reported that they cleared the code only for it to return again and again. Keep in mind that most shops can replace the PCM but not all can program it.

    Other PCM / ECM Codes: P0602, P0603, P0604, P0605, P0606, P0607, P0608, P0609, P0610.

    Hope this help to solve it (remember rated this).

    Aug 03, 2010 | 2001 Dodge Stratus

    3 Answers

    CD disk error


    ok error code 1, look for this error code on your owners manual, toyota cd players give 3 error codes, this mean error code 1, error code 2, and error code 3, they all have different meaning please check owners manuel to see what does error 1 mean i will try looking for you

    May 26, 2009 | 2007 Toyota Camry

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    79 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    75005 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    fordexpert

    Level 3 Expert

    5470 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...