Question about Cars & Trucks

Open Question

Where is crankshaft sensor located on an Isuzu I290 2.9l

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 701 Answers

SOURCE: location of crankshaft sensor

Hello mitchoreb: My name is Roger and I will be glad to help with your answer. You will need to raise the vevicle in order to see the sensor. Make sure to use safety stands when ubder the vehicle when raised up.Look in the area behind the oil filter.Just in front of the knock sensor.This will be just above the oil pan rail.The knock sensor is a round sensor with a round plug.The crank sensor should hove a oblong plug. You should have a picture along with this reply. Should you need any further help please just ask. Please rate the answer you received as this way we know you recived helpful information. Thank You for using FixYa.Roger8d42463.jpg

Posted on May 09, 2009

Ad
polarcycle
  • 1392 Answers

SOURCE: 2004 DODGE STRATUS 2.7L, Location of Crankshaft Position Sensor?

it is located on the right side of the motor, in the trans area. Actually in the bell housing.

Posted on Jun 23, 2009

emissionwiz
  • 76846 Answers

SOURCE: crankshaft sensor location on 2001 oldsmobile

. Its above the starter going into the side of the block. (front side of the engine) Disconnect the battery. Remove the starter. Remove the wIre CONNECTOR plug to the sensor. The sensor has 1 bolt holding it in. Remove the bolt, you may have to wiggle the sensor at the base a bit as you pull it out. Replace, and make sure it is pushed in all of the way. Replace the bolt, wire plug, starter, reconnect the battery.

Posted on Jun 05, 2010

  • 880 Answers

SOURCE: where is the crankshaft sensor located ?

The crankshaft position sensor (POS) is located on the oil pan facing the gear teeth (cogs) of the signal plate. It detects the fluctuation of the engine revolution.
After replacement, ECM reprogramming is required.
This vehicle may be subject to voluntary recall, CAMPAIGN I.D. # R0606, that involves the crankshaft position sensor:

Quote: Nissan has determined that on some 2003 - 2004 Altima and Sentra vehicles with the 2.5 liter engine the operation of the crank angle sensor is significantly affected by variations in temperature that occur due to the unique location of the sensor in the engine. Under certain driving conditions, these variations in temperature can be large enough to cause a brief interruption in the signal output from the sensor. If the interruption in the signal from the sensor is so brief that the Electronic Control Module (ECM) logic does not have time to diagnose the condition, the engine may stop running without warning while the vehicle is driven at low speed.

Posted on Jun 29, 2010

smhb1
  • 146 Answers

SOURCE: crankshaft sensor for vw polo where is the

Crankshaft sensor is located on the right side of the cylinder block behind or under the starter. It is fitted into the rear crankshaft oil seal hausing

Posted on Sep 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where do I locate the crankshaft position sensor on 2004 isuzu rodeo


no engine size stated.
anonymous too, so can read your other posts, why do that?

Aug 14, 2014 | Isuzu Rodeo Cars & Trucks

1 Answer

Check engine light P336


Are you sure this isn't P0336, P336 is not a vaild code not enough numbers.
P0336 ISUZU - Crankshaft Position Sensor Performance
Possible causes- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Faulty crankshaft position sensor
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery Tech notes Sometimes and in some models, low battery voltage or a weak starter can can trigger a Crankshaft Position Sensor code. Before replacing any parts, recharge or replaced battery

Sep 07, 2012 | 2000 Isuzu Rodeo

1 Answer

Crankshaft Positioning Sensor


on a 1996 3.2 L engine the crankshaft positioning sensor is located on the passenger side ! it's easier to access if you remove the tire reach through fenderwell ! it's a ****** to get to. its actually kinda behind and to the rear of the engine mount.

Mar 06, 2012 | 1991 Isuzu Rodeo

1 Answer

How do I locate/replace crankshaft senor on my Isuzu trooper 3 litre diesel car 2001 year .I have been told this is a big job coouls nayone advise please


Its an easy job if you can get the car up high - like on a ramp .just one plug and one bolt to do .
The sensor is behind the exhaust pipe in the clutch bell housing in line with the main oil filter .

Jun 07, 2010 | 2001 Isuzu Trooper

2 Answers

Crankshaft position sensor on a 1996 isuzu hombre


should be between the crank dampener and the block, i mean they are all relatively the same on all cars should be the only wires running close to the crank dampener

Dec 11, 2008 | 1996 Isuzu Hombre

1 Answer

1997 Isuzu Rodeo


on the side of the block on the passenger side....u can see it through the wheel well

Sep 30, 2008 | 1997 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...