Question about Isuzu Cars & Trucks

1 Answer

Where are the test leads to a 2000 Isuzu Rodeo? I was told they were under the left kick panel, but could not see them. I was told one is white(not connected) and the other is black. I see a black one tha is grounded but not sure if that is the right one. It will not start. cranks over good, pulled #2 plug grounded it to motor and it had spark as I cranked it over but no start. was trying to find leads to see what if any codes are stored.Help! can you help me pinpoint the test leads or how else can I find the codes w/out having to tow it to a repair shop or autozone to scan it? thx

Posted by on

  •  Stephen
    Stephen Feb 10, 2014

    Hi glenn - since it should have an OBD2 connector I doubt you can pull codes without a scanner or code reader like the models built before 1995.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Isuzu Master
  • 76,164 Answers

If you mean the OBD2 diagnostic connector it is under the dash on the drivers side in most vehicles

Posted on Apr 21, 2017

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
Richie_asg1
  • 1036 Answers

SOURCE: 1992 Isuzu Rodeo Distributor wires

Hi,

On the 3.2L distriburorless ignition, the firing order is a straight 1-2-3-4-5-6.

Cylinder numbering .

88c39f7.jpg-

Hope this works for you

Posted on Jul 05, 2008

  • 34 Answers

SOURCE: 2001 isuzu rodeo has intermittent starting problems

check battery cables & terminals for tightness & corrosion.also check at starter.check starter bolts & actual starter for looseness.if no problems found your starter may be on its way out.next time it happens hit starter with hammer or heavy object if it starts right up get ready to replace it.good luck

Posted on May 23, 2009

brandyspoile
  • 61 Answers

SOURCE: Crank Sensor in 94 Isuzu Rodeo

it's on the bottom of the motor, towards the back on the passenger side. It has a small clip of wires and one screw holding it on. You may want to pull it up on ramps- if it'll run- otherwise, get under the Rodeo, it's up a little higher than the oil pan, and to the passenger side. (it's right on top of the two lines that run to the bottom of the radiator.) You will need a 10mm socket to remove it. I have added a few pics showing the location (i just completed this task myself)
bfcf016.jpg61ae995.jpgdeffbd6.jpgdd2e415.jpg

Posted on Jul 24, 2009

Hobbit_who
  • 2044 Answers

SOURCE: Cranks no start, have fire to plugs. I have reading all this stuff on this site and fhave not found a solution. does anybody here know anything that actually works? 2000 Isuzu Rodeo 3.2 auto 4x4, tryi

Take this one step at a time:
(a) Does the vehicle start when you spray Starting Fluid into the Intake Air Hose?
If it does, then you need to figure out WHY it is not getting fuel. Possibilities are Clogged Fuel Filter, Bad Fuel Pump, Bad Crankshaft Sensor, Blown Fuel Pump Fuse or other Fuses too...
(b) Do you have a NOIDS Light to test the Fuel Injectors? This will also help you narrow down the troubleshooting

Posted on Feb 13, 2014

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the obd port on my 1993 isuzu Amigo


wow no engine size stated, and MATTERs.!
with no tech1 or 1a scan tooL (real scan tools)
what good is DLC?>
sure jumper CODES< (DTC errors in todays parlance)
there is abs tool.. but only on some cars.

and more. read the FSM yet?
lets pretend you said how do i get the PCM flash error codes
easy jumper the DLC. 'diag, link connector"

google Isuzu DLC jumpers, nets you all this.

http://www.troublecodes.net/isuzu/

there is no world standards for OBD1 so DCL are
every freakn where.

in cab or engine bay or like hondas, on PCM casiing
wild and wolly DLC>


quote

Multi-Port Fuel Injection

Amigo,Trooper II , Rodeo & Pickup
On Rodeo, Amigo, and Pickup (except 1993-95 models W/3.2L engine), connect the single wire diagnostic leads located behind the left hand kick panel together. On 1993-95 Rodeo models W/3.2 engine, the data link is located under the left hand side of the instrument panel. On all models, turn the ignition switch to the On position. At this point, the "Check Engine" light should flash. codes


25011203-uqsqk1sqel1nykdqv4diatnw-3-0.jpg 12pin version below.
jump pins,(for PCM errors) pins A > B
25011203-uqsqk1sqel1nykdqv4diatnw-3-1.gif
the codes are here.
http://www.troublecodes.net/isuzu/iszucel/





25011203-uqsqk1sqel1nykdqv4diatnw-3-3.jpg see no in the engine bay at all, like the 1 guess

Aug 26, 2014 | 1993 Isuzu Amigo

1 Answer

Cranks no start, have fire to plugs. I have reading all this stuff on this site and fhave not found a solution. does anybody here know anything that actually works? 2000 Isuzu Rodeo 3.2 auto 4x4, tryi


Take this one step at a time:
(a) Does the vehicle start when you spray Starting Fluid into the Intake Air Hose?
If it does, then you need to figure out WHY it is not getting fuel. Possibilities are Clogged Fuel Filter, Bad Fuel Pump, Bad Crankshaft Sensor, Blown Fuel Pump Fuse or other Fuses too...
(b) Do you have a NOIDS Light to test the Fuel Injectors? This will also help you narrow down the troubleshooting

Feb 12, 2014 | 2000 Isuzu Trooper

1 Answer

Where do you plug in the code reader for a 92 isuzu. Rodeo


There is no OBD plug to speak of until 1996 and above. However, some models do have a "diagnostic plug" (3 terminal plug) behind the left "drivers footwell" kick panel. There should be a 3-wire harness with a white plug on the end. If you short the #1 and #3 terminals together and then turn on the key, TO RUN ONLY....NOT ALL THE WAY TO START, you should get codes to blink on your "Check Engine Light" or "MIL". Codes can be found online if any have been saved to the ECU.

Oct 25, 2013 | 1992 Isuzu Rodeo

1 Answer

Trying to locate flasher relay on a 2000 isuzu rodeo 4wd


its either under the hood in the fuse box or under the dash on the firewall. if not there take off the drivers side kick panel

Aug 17, 2012 | Cars & Trucks

1 Answer

Locating flasher relay on a 2000 isuzu rodeo 4wd


under the hood in fuse box or under the dash on firewall. if not there take the drivers side kick panel off

Aug 17, 2012 | Isuzu Rodeo Cars & Trucks

1 Answer

Where are the connecters at for checking codes located for a 1997 rodeo with a 3.2 motor and auto trans?


For 1997 Isuzu Truck Rodeo 2WD 3.2L MFI SOHC 6cyl the OBD Diagnostic Link Connector is located: Front seating area, driver side, under dash, mounted above kick panel.

Hope this helps (remembert to rate and comment this answer).

Jul 12, 2011 | 1997 Isuzu Rodeo

1 Answer

Isuzu rodeo tail light relay same as illumination relay under hood?


My 97 Rodeo had the same problem. No Tail lights, no. Dash lights. There is also an annoying buzzer that goes with the set telling you the lights are on, there is no key in the ignition and your door is open. (you don't notice it when it's gone but you sure notice it when it's back)
The Fuse (taillight Illum) was good, The Light relay under the hood was good and all bulbs were good.
What fixed this problem was replacing the tail light relay which is located in a panel just to the left of the brake pedal also called the kick panel.Inside there are 3 relays. I replaced the one in the middle and got everything to work.
If you need to identify the relay you can put your hand over it and then turn the lights on and off. The correct relay should click. Mine was the middle one.
Hope this helps someone because it stumped me for months.

May 20, 2010 | 2000 Isuzu Rodeo

1 Answer

I need a diagram for installing a radio with out a wirering harness


Have fun.

1995 Isuzu Rodeo Stereo Wiring Constant 12V+ Red/White Switched 12V+ Brown/White Ground Black Illumination Green/Red Dimmer n/a Antenna Right Front Front Speakers 4" Dash Left Front (+) Blue/Yellow Left Front (-) Yellow Right Front (+) Green/White Right Front (-) Gray/White Rear Speakers 4" Side Panels Left Rear (+) White Left Rear (-) Red/White Right Rear (+) Orange Right Rear (-) Black/Orange

Feb 26, 2009 | 1995 Isuzu Rodeo

1 Answer

Radio installation


1995 Isuzu Rodeo Stereo Wiring Constant 12V+ Red/White Switched 12V+ Brown/White Ground Black Illumination Green/Red Dimmer n/a Antenna Right Front Front Speakers 4" Dash Left Front (+) Blue/Yellow Left Front (-) Yellow Right Front (+) Green/White Right Front (-) Gray/White Rear Speakers 4" Side Panels Left Rear (+) White Left Rear (-) Red/White Right Rear (+) Orange Right Rear (-) Black/Orange

Dec 30, 2008 | 1995 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...