Question about 2008 Toyota Sienna

Open Question

How long it takes to replace the water pump for 2008 toyota sienna

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Adding daytime running lights to a 2008 Toyota Sienna

http://www.siennaclub.org/forum/index.php?showtopic=3772

DRL's can be added simply by adding a 20 amp fuse into an empty slot in the fuse box.

Posted on Sep 03, 2008

juswannadj
  • 42 Answers

SOURCE: When should you replace timing belt on Toyota

Somewhere between 90,000 mil;es and 120,000 miles you should do your timing belt. But first make sure you do not have a timg chain. If you have a timing chain, you never have to change it at all.

Posted on Sep 10, 2009

  • 1 Answer

SOURCE: Replacing RH Side view mirror on a 2006 Toyota Sienna

I had to replace my passenger side mirror on my 2004 Sienna a while back. I took some pictures as I did it. Maybe this can help.http://time4nothing.blogspot.com/2008/03/fixing-04-sienna-passenger-side-mirror.html

Posted on Oct 04, 2009

ZJLimited
  • 17970 Answers

SOURCE: how to change water pump on toyota sienna

3.0L Engine

  1. Before servicing the vehicle, refer to the precautions section.
  2. Disconnect the negative battery cable.
  3. Drain the engine coolant.
  4. Remove or disconnect the following:
    Wiper and blade assembly Top cowl seal and panel Window washer hoses, from the ventilator louvers Left and right ventilator louvers Heater air duct Timing belt
  5. Mark the left and right camshaft pulleys with a touch of paint.
  6. Remove or disconnect the following:
    NOTE Be sure not to mix up the pulleys.
    Right and left camshaft pulleys bolts Pulleys from the engine
    No. 2 idler pulley by removing the bolt 3 clamps and engine wire from the rear timing belt cover 6 No. 3 timing belt cover-to-engine bolts Water pump nuts/bolts Water pump and gasket from the engine

    9c53b11.jpg
    Fig. Exploded view of the components to gain access to the water pump-3.0L engine


    cf2cc65.jpg
    Fig. Exploded view of the water pump and related components-3.0L engine

To install:
  1. Check that the water pump turns smoothly. Also check the air hole for coolant leakage.
  2. Apply liquid sealer to the gasket, water pump and engine block.
  3. Install or connect the following:
    NOTE After tightening the bolt, be sure the idler pulley moves smoothly.
    NOTE Be sure to align the knock pin hole on the camshaft pulley with the knock pin on the camshaft.
    NOTE Be sure to align the knock pin hole on the camshaft pulley with the knock pin on the camshaft.
    Water pump, using a new gasket. Tighten the nuts/bolts to 53 inch lbs. (6 Nm). Rear timing belt cover. Tighten the 6 bolts to 74 inch lbs. (9 Nm). Engine wire with the 3 clamps to the rear timing belt cover No. 2 idler pulley. Tighten the bolt to 32 ft. lbs. (43 Nm).
    Right-hand camshaft pulley, with the flange side outward.
    Tighten the camshaft bolt to 65 ft. lbs. (88 Nm), using the removal tools Left-hand camshaft pulley, with the flange side inward.
    Tighten the camshaft bolt to 94 ft. lbs. (125 Nm), using the removal tools Timing belt
  4. Fill the engine coolant.
  5. Install or connect the following:
    Heater air duct Left and right ventilator louvers Window washer hoses to the ventilator louvers Top cowl seal and panel Wiper and blade assembly Negative battery cable
  6. Start the engine.
  7. Top off the engine coolant and check for leaks.

Hope this help.

Posted on Mar 23, 2010

  • 7353 Answers

SOURCE: Replace oil filter for 2008 Toyota Sienna - Special Service Tool

Special Service Tool from Toyota is part number 09228-06501

Posted on May 11, 2010

Testimonial: "Thanks for the help. At least now I have something to work with."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does a 2008 Toyota sienna have a fuse for front washer pump


Yes there are two fuse blocks on the van. One in the engine compartment and the other under lower dash panel fronting driver. Use a circuit light tester to probe the power terminal on the washer pump first to determine if you have power coming there when you turn on rear washer pump switch. You will need another person to help. Rear pumps fail often because of the lack of usage

Feb 09, 2017 | 2008 Toyota Sienna

1 Answer

How do you replace 2008 toyota sienna RH side mirror


Call the dealer to see if the glass element can be replaced, most can.

Aug 17, 2012 | 2008 Toyota Sienna

1 Answer

2008 sienna water pump replacement


For 2008, the water pump is not driven by the timing belt. Also, the motor does not have to be lifted. The haynes manual says to pull the ac unit, alternator, and drive axle, which is not required. Also, you do not have to lift the motor. I saw this on the net, which is incorrect for 2008 Sienna.1) Drain the system of anti-freeze2) take-off the passenger side front tire to get to the access panel, using a jack stand on the body.2) remove the access panel, and you should see most of the bottom bolts of the water pump3) do not remove the serpentine belt just yet, crack the bolts holding the water pump pulley, but do not remove them. If you remove the belt, you will be fighting against yourself to unloosen them later. 4) remove the serpentine belt (see youtube - a guy has a video of this piece which is easy)5) remove the top engine mount, which has about 4 bolts6) remove the aluminum bracket surrounding the thermostat housing which has about 7, and yes, some are long. 7) remove the thermostat housing, and disconnect the 3/4 hose in the back8) remove the belt tensioner pulley, by wrenching clockwise. 9) remove the 2nd serpentine pulley10) remove the 4 bolts for the water pump pulley11) remove the 16 bolts of the water pump12) reverse your order, and you should be good to go. Also, I replaced mythermostat, when the housing was out. Good Luck !

Feb 23, 2012 | 2008 Toyota Sienna

1 Answer

Have a 2008 toyota sienna and the check engine light is on. It said o2 sensor I replaced and still check engine light is on.


Codes DON'T tell you what to replace

Study OBD2 Systems

You just had a sensor reporting an out
of range condition

You then have to diagnose the reason

Have a professional take over

Mar 13, 2011 | 2008 Toyota Sienna

1 Answer

Replace oil filter for 2008 Toyota Sienna - Special Service Tool


Special Service Tool from Toyota is part number 09228-06501

May 11, 2010 | 2008 Toyota Sienna

2 Answers

No heat on 2008 sienna, replace t-stat. one rad hose and one heater hose hot. other rad hose & heater hose cool


If your top rad. hose is cool and the engine is smoking hot, it probably is a blown head gasket. What does you temp gauge read ?

Feb 01, 2010 | 2008 Toyota Sienna

2 Answers

When should you replace timing belt on Toyota Sienna van? It's a 1999 model with 210,000 kms on it and I need a new water pump. Should I replace the timing belt at the same time?


Somewhere between 90,000 mil;es and 120,000 miles you should do your timing belt. But first make sure you do not have a timg chain. If you have a timing chain, you never have to change it at all.

Sep 08, 2009 | 1999 Toyota Sienna

1 Answer

2008 Toyota Sienna Engine knocking


Have the knock sensor checked.

Jul 22, 2009 | 2008 Toyota Sienna

1 Answer

2008 toyota sienna


arent you under warranty

Feb 13, 2009 | 2008 Toyota Sienna

1 Answer

How to do front brake on 2008 toyota sienna


No special tools at all. Are you familiar with doing brakes? I wouldnt recommend it for a first timer, its not worth the lives of you and others. Ive also seen people take the wrong bolt out of calipers and spend triple what a brake job cost because they werent experienced and wanted to save a buck. A 17mm and pad spreader or big channel locks is all you need. Use Toyota pads and have the rotors cut..OR... Dont complain when they make noise all the darn time!

Jan 09, 2009 | 2008 Toyota Sienna

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...