Question about GMC Sierra

Open Question

Schematics 2000 GMC Sierra ignition switch wiring diagram

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 59 Answers

SOURCE: 1997 GMC Sierra Ignition Switch Replacement

take off the cover on the top and bottom of the steering column just behind the wheel. pop the tilt lever out simply just by grabbing it and give it a good tug. then once you have the new switch and you get in there your going to need an inverted torx socket to remove the small bolts that hold the switch to the column. do not move the gear on the new switch make sure it lines up exactly as the old one did!!!!!!!!!!!!

Posted on Mar 15, 2009

emissionwiz
  • 75807 Answers

SOURCE: stereo wiring diagram

1999 GMC Sierra Truck Radio Wiring Guide
Car Radio Battery Constant 12v+ Wire: Orange
Car Radio Accessory Switched 12v+ Wire: Yellow
Car Radio Ground Wire: Black/White
Car Radio Illumination Wire: Brown
Car Stereo Dimmer Wire: Gray
Car Stereo Antenna Trigger Wire: N/A
Car Stereo Amp Trigger Wire: N/A
Car Stereo Amplifier Location: N/A
Car Audio Front Speakers Size: N/A
Car Audio Front Speakers Location: N/A
Left Front Speaker Positive Wire (+): Tan
Left Front Speaker Negative Wire (-): Gray
Right Front Speaker Positive Wire (+): Light Green
Right Front Speaker Negative Wire (-): Dark Green
Car Audio Rear Speakers Size: N/A
Car Audio Rear Speakers Location: N/A
Left Rear Speaker Positive Wire (+): Brown
Left Rear Speaker Negative Wire (-): Yellow
Right Rear Speaker Positive Wire (+): Dark Blue
Right Rear Speaker Negative Wire (-): Light Blue
-->

Posted on Apr 15, 2009

  • 82 Answers

SOURCE: 87 regal ignition switch wiring diagram

Thick wires at IGN SW .... Red(s) - supply power from the battery to the IGN switch ... Pink - ignition supply ... Orange - Accessory power ... Purple most RWD sometimes (Yellow most FWD) - Starter .. Did I miss any? It's been a while The thin wires on the IGN swich are for key sense and VATS (if applicable)

Posted on May 08, 2009

  • 819 Answers

SOURCE: 2000 gmc sierra, blower motoronly works on #4,5

chances are the switch is fine, and its the blower motor resistor. this is a small circuit board inserted in the airbox around the fan area, under the dash on the passenger side, held in by two 7/32" head screws. it is available at any parts store. very common problem.

Posted on Dec 22, 2009

  • 1 Answer

SOURCE: wiring diagram 2003 GmC Sierra

I need wiring digram for GMC 2003 SIERRA . I have the left head light working fine but the right I have no power to it. I have checked the fuses and relaysand so far have not found and broken or frayed wires.

Posted on Mar 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Color coded wiring diagram 1995 gmc sierra electric windows


Google the
wiring diagram 1995 gmc sierra electric windows I found several systems offering what you require.
But what is the problem, 99% of the time in that year the window regulator was at fault, it was made from a stapped steel housing verses an cast unit. We check the left switch for power, disconnect the two wire connector at the motor, and see if the motor has power to one side or the other in the connector. If the switch has power to it, and the motor has power to it as you press the button, the motor is at fault.

Good luck.

Mar 16, 2015 | GMC Cars & Trucks

1 Answer

I have a 2008 gmc sierra 1500 series and it turns on but i can't get it to shut off?


I think I would try a new ignition switch or at least unplug the switch after the engine is running and see if it stops running. When you initiate a start, a series of relays turn on in the powerbox. If the ignition relay is melted inside itself, it will not break connection. You can research and get diagrams, videos, and photos on the Web. Just be specific and enter the year, make, and model and ask for a wiring diagram or fusebox or powerbox for that truck. Then chose from the results.

You should be able to identify the correct relay from the diagrams. Relays are not terribly expensive.

Nov 29, 2014 | 2008 GMC Sierra 1500 2WD

1 Answer

How can i find a wireing diagram for a 2000 gmc sierra 3500


Depending on which diagram you need, some auto parts websites have diagrams you can access after you register with them.
Otherwise you would need to buy a shop manual.

Oct 19, 2014 | 2000 GMC Sierra

1 Answer

On my 1991 gmc my my heater switch does not come on check fuses still nothing


either main power to switch or ground wire from switch loose, bad connection , etc., I believe the main power source is through ignition switch ! I'll look @ my wire diagram & get back to ya, its EASTER, AFTER 1:00AM , see ya later !

Mar 31, 2013 | 1991 GMC Sierra

1 Answer

Driver's window


The wiring diagrams for your 2003 GMC Sierra power window circuits are copyrighted material and cannot be posted here. However, I can describe the driver's power window circuit to you.

Battery voltage is provided to the driver's window (master) switch via the ORANGE wire at PIn #2 on the switch connector which comes from the 25 Amp Left Window Circuit breaker located in the fuse block on the left side of the dash.

There is a logic module located inside of the master switch which controls the "Auto Down" feature for the driver's window. When the switch is operated in either the "UP" or "DOWN" position, power and ground is supplied to the window lift motor via the BROWN wire (Pin #1, Connector 2) and the DARK BLUE wire (Pin #3, Connector 2) Thease wires will switch polarity dependin on whether the switch is commanding UP or DOWN.

The schematics show that the ground circuit for the driver's window motor is supplied internally by the driver's window switch module. It is most likely grounded inside the door panel itself - the schematics do not specify. To check for ground, you can test continuity to ground on BOTH the BROWN and the BLUE wires by back-probing them with the switch electrical connector plugged in and the window control switch in the NEUTRAL position. They should both have ground.

When the switch is operated, one will remain ground while the other switches to power.

Mar 24, 2012 | 2003 GMC Sierra

1 Answer

2000 GMC 2WD No communication @ OBD II connector - all ignition and ECM fuses good. Vehicle has 4" body lift - but no sign of torn grounds, etc.


you will need a wiring diagram to find problem, first make sure the power feed circuit is good, use a test light or volt meter will be better, some times cigarette lighter circuit and o.b.d.II feed share same circuit. also look at signal circuit. it should b between 5*7 volts.

Jan 20, 2011 | 2000 GMC Sierra

1 Answer

2000 gmc sierra dash lights and running lights remain on after


It seems you have a sort circuit in the wiring or the switch......

normally you have 2 types of shorts, 1 is to earth and this causes the fuse to blow, indicating a fault and preventing a fire.

The second one is a short to power, where the circuit remains on, despite the switch being turned off.

I would suggest that the park light switch is shorting out.

If you are not familiar with electronics, I would prefer you seek an auto electrician to do the job.

Jul 30, 2010 | 2000 GMC Sierra 3500

1 Answer

Help me reinstall ignition on 2007 gmc sierra hd sle!


Get a manual from an auto parts store specific for your vehicle. In it, you'll find exploded parts diagrams and step by step instructions on how to replace those parts

Apr 15, 2017 | 2007 GMC Sierra 2500HD

1 Answer

1997 GMC Sierra Truck Ignition Switch


its a long process,you need a steering wheel puller, once its off take the hazard button assembly out, take the turn signal loose, pull old ignition out, carefully install new one, and reverse procedure and always if u get confused i would highly recomend
a chiltons manual they explain things great

Feb 16, 2009 | 2000 GMC New Sierra 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...