Question about Cars & Trucks

Open Question

How to remove the cover of Minox T8

I have removed the hidden screw but now still the cover is somehow atatched to the viewing side of the device

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: 2000 mercury cougar front door panel removal

its very easy, takes maby 10min, there are hidden screws under the cougar symbols on the door, and under the black circles on the carpeted part of the door, they all just pop off, then there are a few on the ouside rim of the door 2 on each side i think, it might require a little jiggling but the car is pretty simple

Posted on Mar 16, 2009

Ad
  • 1 Answer

SOURCE: replace rear turn signal bulb on 2007 H3 - driver side

1st::Unscrew the 2 screws that hold the light in.
2nd::Slide your hand behind the light and pull the light towards you. Make sure that you pull it straight, as if the h3 was driving away from you, so you dont break the two pins that are holding the light in...PULL ONE PIN AT A TIME!!!

Dont pull it to far away from the hummer as there are wires attached that need to stay attached.

3rd::turn the back of the bulb to unlock it from the lens...
4th:: slide the bulb out and remove thebulb by pulling it straight out.
5th::put the new bulb in, lock it back into the lens, then insert it back where you got it from,...

MAKE SURE you move the wires out of the way when you put the lens back in...they will get in the way and can be damaged.

Posted on Apr 07, 2009

honeymokey
  • 3113 Answers

SOURCE: Removing passenger door panel

There is a screw behind the lock rod. Lift door panel straight up to remove

Posted on Jun 13, 2009

  • 1 Answer

SOURCE: replacing side view mirror cover on 200 SAAB 9-5

I need a complete passenger Side Mirror (2nd Hand) N-95 (S Reg) contact 07966 366195

Posted on Jul 21, 2009

  • 318 Answers

SOURCE: 2002 Toyota Rav4 remove door panel

There are some hidden screws around the door handle but you get under the panel and yank hard to pop the fasteners. Also remove the black piece behind the mirror. Alot of times it is seperate. 3 screws behind that and the connector and you are done.

Posted on Jul 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 bmw 320i E90 replace number plates ?


Normally these are simply screwed to the vehicle bodywork with either 2 or 4 screws. It is just a matter of locating the screws and removing them using a basic screw driver with the correct head (either flat head driver or Phillips Head driver if PH screws have been used). If the screws are hidden from view and access because someone has fitted a set of fancy number plate covers to your plates you will have to remove the number plate covers first.
https://www.google.com.au/search?q=phillips+head+screwdriver&tbm=isch&tbo=u&source=univ&sa=X&ei=-5_kVMDSCeHbmgWO-YLwCg&ved=0CDcQsAQ

Feb 18, 2015 | BMW Cars & Trucks

1 Answer

Need to replace blower fan motor 2006 Chevy Malibu


2004 and up, the old blower motor must be cut out with a utility knife and the new one screws into the opening to the screw holes molded into the plastic housing. It is located under the passenger side dash, you may have a silencer / plastic cover there you have to remove to view it.
  • Remove the passenger's side lower silencer panel.
  • Remove the blower motor wire harness connector.
    Two diagrams show how it goes:
    2011-02-17_212631_1.gif
    Cut along the narrow groove where the arrows indicate. Do not cut too deep, only enough to remove motor, as the cup will be re used.
    2011-02-17_212646_2.gif
  • Install new motor assembly with three screws, usually provided with new unit. Tighten securely.
  • Atatch wire harness. Test unit. If functioning properly, replace silencer / cover.
  • Jul 22, 2014 | Cars & Trucks

    1 Answer

    Need to remove door panel. How?


    Door Panels - REMOVAL & INSTALLATION

    The many different design interiors make it impossible to list each fastener location. The trim panels that must be removed are held in place by screws and clips. These locations vary from model to model. After removal of all the fasteners that you are aware of, if the trim panel is still firmly attached, you probably missed a hidden fastener. If this happens, gently and carefully pry the area looking for the location that doesn't flex. The location that does flex is where you'll find the fastener(s) you missed. Screws and retainers are usually hidden. Handle trim, reflectors, light lenses and other plastic pieces usually cover the main retaining screws. Take great care with the plastic trim panels. Plastic trim panels are usually very hard plastic and extremely easy to crack. The following steps can be used to guide you through the removal and installation of the trim panels, but you may need to alter these steps to your specific needs.
    1. Disconnect the negative battery cable.
    2. Pull the inside door handle to the open position, unfasten the screw and remove the handle escutcheon.
    3. If equipped with manual locks, remove door inside locking rod knob.
    4. If equipped with manual windows, insert a suitable window regulator handle removal tool behind the handle. Disengage the retainer, then remove the handle.
    5. If equipped with power windows and locks, use a small flat-bladed prytool to carefully pry the switch plate up, then detach the power component electrical connectors.
    6. If equipped, remove the screws inserted through door armrest and pull handle assembly into door inner panel or armrest hanger support bracket.
    7. Lift the seat belt trim panel up and remove the hidden retaining screws.
    8. Remove the outside side view mirror trim plate retaining screw. Lift the panel up to disengage the retaining clip, then remove the trim panel from the door.
    9. On styles with courtesy lamps located in the lower area of the trim panel, disconnect the wiring harness at the lamp assembly.
    10. If equipped, use a suitable tool to pry the reflector plate from the side of the door panel.Remove bottom trim cover retaining screws, then remove the lower trim cover.
    11. Remove any necessary electrical connector CPA clips, then unplug the electrical connectors.
    12. On styles with integral armrests, remove the screws inserted through the pull cup into the armrest hanger support.
    13. Unfasten the door trim panel retaining screws. The locations of the screws will vary depending upon the year of model of vehicle. The screws are usually hidden, so be sure to look carefully to make sure you don't miss any.After all of the trim panel retaining screws are removed, slide a suitable trim panel removal tool between the door panel and door perimeter to carefully disengage all of the trim panel retaining buttons. Make sure to position the tool close to the fastener, or the trim panel may be damaged.
    14. Carefully lift the trim panel away from the door, checking to be sure all of the retaining buttons and screws and electrical connectors are unfastened.

    To install:


    Before installing the door trim panel, check that all trim retainers are securely installed to the panel and are not damaged. Replace damaged retainers as required.
    1. Connect electrical components where present.
    2. To install the door trim panel, pull door inside handle inward; then position the trim panel to the inner panel, inserting the door handle through the panel hole.
    3. Position the trim panel to the door inner panel so that the trim retainers are aligned with the attaching holes in the panel, and tap the retainers into the holes with a clean rubber mallet. Install all previously removed items.
    4. Install the remaining door panel components in the reverse order of removal.
    5. After installation, connect the negative battery cable, then check for proper attachment and operation of electric components, if so equipped.

    Hope helps (remember rated and comment this).

    Jun 29, 2010 | 1987 Oldsmobile Delta 88

    1 Answer

    Need a diagram for installing a drivers side electric power mirror on a 1995 mercury villager van


    here's 1996, all I have. Please rate.

    Mirror, Power — Outside Rear View NOTE: This procedure applies to both RH and LH power outside rear view mirrors.

    Removal
    1. Remove the front door trim panel (23942). Refer to Section 01-05 for the removal procedure.
    1. Remove the two outside rear view mirror inside mounting hole cover screws and the outside rear view mirror mounting hole cover (17K709) from the front door (20124).




    1. Remove the wire clip.
    1. Disconnect the power outside rear view mirror electrical connector.




    1. Remove the three power outside rear view mirror bolts and the power outside rear view mirror.




    Installation
    To install, reverse the removal procedure. Tighten the three power outside rear view mirror bolts to 3-4 Nm (27-35 lb-in). Glass, Outside Mirror
    Removal and Installation
    Refer to the glass replacement procedures in Manual Mirror for power outside rear view mirror glass (17K707) Trim Cover
    Removal
    1. Remove the front door trim panel. Refer to Section 01-05 for the removal procedure.
    1. Remove the two outside rear view mirror inside mounting hole cover screws.


      Remove the outside rear view mirror mounting hole cover.
    Installation
    To install, reverse the removal procedure. Mirror Control
    Removal
    1. Use a small flat-blade screwdriver to pry the power outside rear view mirror control switch from the instrument panel (04320).


    May 13, 2010 | 1995 Mercury Villager

    1 Answer

    2002 Toyota Rav4 remove door panel


    There are some hidden screws around the door handle but you get under the panel and yank hard to pop the fasteners. Also remove the black piece behind the mirror. Alot of times it is seperate. 3 screws behind that and the connector and you are done.

    Jul 18, 2009 | 2002 Toyota RAV4

    1 Answer

    How to remove jaguar center console


    As in you want a diagram? Either way, I don't have one but I have managed to remove it. I don't know if this might help but I start off by forcibly removing it by holding on to both sides of the top of the console (where the ash tray resides). Upon removal, I remove the cover of the ash tray by unscrewing two screws on both sides of the cover. These require a cross screwdriver. I then take off the connectors to both of the buttons where the gear lever is. The leather surrounding the handbrake is a bit tricky to remove. Slowly unbutton it then remove the top plastic part; you might lose the little spring that holds the button if you aren't careful. Then open the arm rest. Two Torx screws are located by the pivot point of the arm rest. I'm sorry I can't remember the size (most likely an T8). That's just about it. Hope this helps

    Jul 14, 2009 | 2001 Jaguar S-Type

    1 Answer

    Do I require any special tools to remove the front passenger seat of a 2005 Volvo S40 please? The mountings seem to be hidden by plastic covers and I can't see away of removing these? Presumably they pull...


    There may just be one screw that holds, one end of the cover, then you can slide it off. But you will have to bend over backwards.
    The fixings may be star bits, but other than that, just regular bolts and nuts.
    Hope that helps.

    Jul 13, 2009 | 2004 Volvo S40

    2 Answers

    How do I remove interior front door panel


    You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. then just remove the bolts for the mirror

    May 16, 2009 | 1997 GMC Jimmy

    1 Answer

    How to remove heater core in 2002 chevy s10 pu. got dash out and lines off are there hidden screws?


    There is a black covering on passenger side that should have four screws in it. You should find the heater core hidden inside the casing.

    Mar 03, 2009 | 2002 Chevrolet S-10

    1 Answer

    How to remove tailgate cover


    most car all makes these days use push clips on the hidden panel side or visible screws or smaal cicular covers hidding the screw heads or a combination of clip and screw.pull the panel towards you inspect it has a lip at the window glass then push to the sky,

    Jun 02, 2008 | 2007 Honda CR-V

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    51 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    76164 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...