Question about 1993 Toyota Camry V6

1 Answer

To replace ignition coil on 1999 toyota camry

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Toyota Master
  • 20,706 Answers


mark wires, unbolt old ,put in new put wires back AS FOUND.
that works from 1929 to 2014.

what engine of the many.
what is this question,
id say if you dont know how to unbolt a black cube
to get help, fast. or read the FSM.

Posted on Feb 19, 2014


4 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 98 Answers

SOURCE: How to remove ignition cylinder from Toyota Camry 1993

Here are step-by-step instructions for the removal and re-installation of your ignition cylinder on your Toyota. Hope this sheds some light on the subject and solves your problem. Have a great day!

  1. Disconnect the negative battery cable. If equipped with an air bag, wait at least 90 seconds before working on the vehicle.
CAUTIONSome models covered by this guidemay be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in .
  1. Remove the lower steering column cover. Unfasten the ignition switch connector under the instrument panel.
  2. Remove the screws which secure the upper and lower halves of the steering column cover.
  3. Turn the lock cylinder to the ACC position with the ignition key.
  4. Push the lock cylinder stop in with a small, round object (cotter pin, punch, etc.).
On some vehicles, it may be necessary to remove the steering wheel and combination switch first.
  1. Withdraw the lock cylinder from the lock housing while depressing the stop tab.
  2. To remove the ignition switch, unfasten its securing screws and withdraw the switch from the lock housing.
To install:
  1. Align the locking cam with the hole in the ignition switch and insert the switch into the lock housing.
  2. Secure the switch with its screw(s).
  3. Make sure both the lock cylinder and column lock are in the ACC position. Slide the cylinder into the lock housing until the stop tab engages the hole in the lock.
  4. Install the steering column covers.
  5. Connect the ignition switch wiring.
  6. Connect the negative battery cable.

Posted on Nov 23, 2008

  • 1861 Answers

SOURCE: coil pack

Cylinders 2 - 4 - 6 are facing the radiator. Cylinder 2 is closest to the drive belts.

Cylinders 1 - 3 - 5 are facing the firewall, cylinder one closest to the drive belts.

Hope this helps; and Thanks for choosing FixYa for assistance.

Posted on Feb 25, 2009

  • 11 Answers

SOURCE: 1990 Toyota Camry just stopped running has no spark but has fuel.

check the main fuses under the hood to see if any are blown

Posted on Jul 23, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Already replaced ignition coil and wire plug. But don't have spark on cylinder# 3 on my 1999 toyota camry. What can I do?

Hi,first see if the plug is falty,then change the H,T,Leads and distributer cap,
if this dose not work then you should do a compression test as it could be one of the valves,
I hope the first diagnoses is the one.
hope this helped some,all the best,let me know how you got on.

Apr 17, 2015 | 1999 Toyota Camry

1 Answer

Ignitio coil

3 posts now, and not one question?
and no engine stated.
ok again.
1: what country
2: what car, CAMRY?
3: what sub model, XV20:
4: what engine , the 5S or 1MZ?????????? key question !!!!!
we can NOT GUESS this. (sans a photo with hood open)
and now ill answer for the blue box above. (hope its right, i do)

there are 6 coils. which one.?
unscrew it. its out..

Feb 10, 2014 | 1999 Toyota Camry

1 Answer

Iginition coil

which sub model? XV20? 1999 CAMRY
did you post the wrong car, wrong year, or wrong engine>?
perplexing this is.
you meant 5S right, not 3S? it had no 3S , sorry 1.
you dont know engine you have???????
runs the 3S are you confused on car modeL.

V20 (1986-1990) Camery run this motor, 1 of 8 engines offered,.

ill roll dice 1999 Camry, XV20 5S engine.
try a real question, statements don't work. but are fun...
i want to....????
sure go ahead, we give you permission..
are you guessing out loud.? thats ok too.
why not post symptoms and all evidence.
or ask a real question.?????
like, ?where is my ignition coil (there are 6)
answer it's connected to the spark plugs.
how do i remove it?, , answer you , unscrew it.

in the USA our XV20 has 5S engine with 6 COP ignition coils.
we also have a 1MZ engine in 1999. XV20 car.
but both engines run COPS. in USA/ and a turbo option too.
are you in the USA, other countries run diffr, engines.

Feb 10, 2014 | 1999 Toyota Camry

1 Answer

I have a 1999 toyota camry and my key in the ignition cylinder wont turn i moved steering wheel and its on park do ineed to replace ignition cylindern

If the key will not turn the lock cylinder and you have removed the switch, you probably need a new cylinder.

Sep 07, 2012 | 1999 Toyota Camry

1 Answer

My camry is having a random misfire on cylinders 2 4 6

Sounds like the ignition coil for that side of the engine is going bad.

Sep 11, 2011 | 1999 Toyota Camry

1 Answer

How can I tell if the ignition switch is bad in my toyota camry?

You need a tachometer compatible with the Toyota Camry's ignition system. Start up the Camry's engine and let it reach normal operating temperature. Connect the tachometer tester probe to terminal IG of the Data Link Connector 1. Connect terminals TE1 and E1 of the DLC1 with a jumper connector. Inspect the tachometer's timing. It should be between 8 and 12 degrees Before Top Dead Center. Set the timing as necessary. Tighten the hold-down bolt and make sure the ignition timing advances. Ignition Coils Disconnect the negative terminal from the Camry's battery. Remove the two nuts and clips on top of the cylinder head cover, then remove the cover. Disconnect the four ignition coil connectors and the bolts retaining the coils. You can now remove the coils. Replace the coils as needed. Connect the bolts and coil connections and replace the cylinder head cover.

Aug 31, 2010 | 1999 Toyota Camry

1 Answer

Key will not turn in ignition after battery replacement

The battery is either bad or the starter brush has chopped down bad.

May 23, 2009 | 1999 Toyota Camry

2 Answers

Toyota camry 1994 220 sei, non start

Replace the ignition coil under the distributor cap.
Common problem.

Aug 11, 2008 | 1994 Toyota Camry

Not finding what you are looking for?
1993 Toyota Camry V6 Logo

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

79024 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides