Question about 2006 Chevrolet Cobalt LS

Open Question

How to install new starter in 2006 chevy cobalt 2.2 L engine?

Just need to know how t install starter.

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: how do i change the car battery for 2006 cobalt?

the battery is located in the trunk under the carpet where the spare tire is located, loosen the 10 mm nuts on the terminals and pull them off, gently pull the vent hose from the battery, loosen the bolt for the battery hold down, usually a 13mm or 15mm, remove battery and reverse the process to install

Posted on Jun 19, 2009

  • 98 Answers

SOURCE: 2006 chevy cobalt - door won't open

Start with the basics. Check the fuses (all of them) with a test light and be sure you have power to each and that they are good. Then be sure that the power lock relay is good by swapping it with another relay in the fuse block. If the fuses are good and the relay is swapped and the locks still aren't functioning, you may have an issue with the BCM. The BCM can be programmed to change the behavior, but if the car has had water damage, or other stress to the BCM (voltage, heat, etc.), it can sometimes damage the BCM and you will need to replace it and reprogram it at a GM dealership.

Posted on Jul 25, 2009

  • 521 Answers

SOURCE: my 2006 chevy cobalt 2.2 liter sputters

Fault with the IAC valve.there maybe a trouble code associated with it also./ Go to your nearby autozone or auto parts retailer and ask them to put a scanner to the car....make note of the codes if any are found. the IAC valve i usually locate don the throttle body and can be removed for inspection and sometimes cleaning using a good throttle body cleaner spray and a pipe cleaner brush.

Posted on Aug 04, 2009

  • 124 Answers

SOURCE: Fan switch does not work in the 1, 2, 3, position 2006 Cobalt

You have a problem with the blower motor resistor. This is a very commen problem on all gm cars and light trucks. The part is not to pricey. You can find the resistor under the glove box buy the blower motor. Two bolts and out it comes.

Posted on Sep 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to know how o install a starter into a chevrolet impala. Need to know where the wires need to go


just follow the positive battery cable to engine block ,the starter is at the end of wire ,i believe is a 15mm socket to remove two bolts holding starter and also there is one tiny nut holding a small wire at the back of starter ,,,,,,good luck

Mar 22, 2011 | 2006 Chevrolet Impala

1 Answer

My husband has a 1986 dodge ram van 350 with a 318 engine automatic and needs to know how to take out old starter solenoid and install a new one


He needs to disconnect battery, climb under truck undo 2 bolts holding starter to engine, undo 2 wires and it's out. Reverse to install. (I know easier said than done)

Mar 05, 2011 | Dodge Ram 350 Cars & Trucks

1 Answer

I need to know how to install the new starter a 1987 camero.


General procedure to replace a starter is to disconnect the battery, un-bolt the starter from the engine,
remove the wires from the solenoid (mark them so you know where they go) and reverse the process to install. If there is anything in the way of physically getting the starter out, remove or move it out of the way. some starters require a bit of turning to get them to clear obstructions. If your radio has a security code, know it before disconnecting the battery...same for security systems if you have one.
The connections on the starter are mounted in a plastic cap....don't over-tighten or you will break it.

Feb 28, 2011 | 1987 Chevrolet Camaro

1 Answer

HOW TO INSTALL THE PROSTART STARTER TO 2001


First you will need a transponder bypass modual for a 2001 dodge caravan with MUX output, if your ignition key is grey, you may also need a total of 6 resistors for this van depending on what features you want and at least 2 relays, then just follow the install diagram, if you run into ant problems you know where to find me, I have done dozens of thses vans so I know what will be required, if you need the bypass modual or any of the 6 resistors let me know

Nov 05, 2009 | 2001 Dodge Caravan

1 Answer

Replace a starter


1999 Honda Civic DX 1.6L MFI SOHC 4cyl
Starter Removal & Installation

c4ae816.gif

Fig. Starter wire connections

304d19e.gif

Fig. A ratchet and long extension may be needed to remove the starter

The factory sound system has a coded theft protection system. It is recommended that you know your reset code before you begin.
  1. Disconnect the negative battery cable.
  2. Remove all wiring from harness.
  3. Remove the lower radiator hose from the bracket on the starter motor.
  4. Remove the starter cable from terminal B located on the back of the solenoid.
  5. Remove the black/white wire from the S (solenoid) terminal.
  6. Remove the two bolts that mount the starter to the transaxle assembly.
  7. Remove the starter.

To install:
  1. Install in the reverse order of removal.
When installing the heavy gauge starter cable, make sure the crimped side of the terminal end is facing out.
  1. Enter the anti-theft code and radio presets.

I hope help you with this (rated this help). Good luck.

Sep 09, 2009 | 1998 Honda Civic

1 Answer

Need to know how to install starter on 1997 ford


There "should"only be one large red wire coming from the starter relay on the pass. side fender well going directly to the starter.
It may be black, but i'm sure it's red.

Aug 14, 2009 | 1997 Ford F150 Regular Cab

4 Answers

I need to pull and reinstall starter on '93 audi cs90


starters seem difficult, but can be accomplish relatively quickly. there friendly because you don't have to worry about belts and gaskets. My assumption here is that you know you need to replace the starter and you know where the starter is located.
first disconnect negative battery cable.
On the starter you will need to disconnect power and ground. then you can pull the bolts and remove the bad starter. Installation is reverse of course. Once installed and secure, always double check the gound connection. reconnect battery and off ya go. Time should 45ish minutes.

May 05, 2009 | 1993 Audi 90

2 Answers

How to change starter on 1994 jeep wrangler


is it the straight six? if so first disconnect the battery then there should be 2 bolt 13 or 14 mm. take wires off. then reverse for install.

Mar 11, 2009 | 1994 Jeep Wrangler

1 Answer

Replacing a starter for a 1999 Altima


  1. Disconnect battery ground cable.
  2. Disconnect starter wiring from starter.
  3. Remove starter retaining bolts and the starter.
  4. Reverse procedure to install.
the bolts should be on the drivers side.
you will have to crawl underneath the car to do this task

May 15, 2008 | 1999 Nissan Altima

Not finding what you are looking for?
2006 Chevrolet Cobalt LS Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...