Question about 1999 Hyundai Accent

Open Question

1998 mercury mountaineer rear parking brake shoe in disc brakes

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
maklean
  • 1665 Answers

SOURCE: remove rear brake drums

0f2c8a8.gif
1. After removing the wheel, remove the brake drum. 2. Remove the shoe hold down spring, the automatic adjuster spring and adjuster lever.
7b7d17f.gif
3. Spread the shoes and remove the shoe adjuster. 4. Remove the shoe to shoe spring and shoe hold down spring.
a1a62c3.gif

Posted on Jun 03, 2008

Ad
  • 1 Answer

SOURCE: parking brake

I just replaced rotors on my 2003 Santa Fe, There are 2 phillips screws in the rotor that must be removed. There is an auto adjuster on bottom of brakes. That inspection hole is very small! Sometimes you must tap a hammer around the drum to loosen the rust. Hope this helps.

Posted on Oct 08, 2008

losflip
  • 94 Answers

SOURCE: 2002 Hyunsai Accent rear brakes, do you have to remove wheel hub

Yes, it should be removed it makes the job a lot less difficuilt. 

Posted on Nov 30, 2008

  • 98 Answers

SOURCE: parking brake adjustment

On the accents what you need to do is to remove the plastic casing from around the parking brake mechanism. Towards the back on each side there is a screw that needs to come out. Then you will just need to wiggle the plastic casing out and around from the parking brake and set it aside with the screws. Once that is off on the inside there will be what looks like one long (gold colored) screw and at the bottom there will be a mini cable running off to each side. At the end of the tension adjuster is where you adjust it. Mine was very loose and I had to tighten it down quite a bit. It takes a 12 MM wrench. You will want to turn the wrench toward the passenger side to tighten it down. Hope this works for you.

Posted on Feb 25, 2009

  • 88 Answers

SOURCE: PARKING BRAKE LEVER- NO TENSION / DISC BRAKE ADJUSTMENT-OFF

If you remove the cover of the E-brake there should be a tention ajustment that you can do yourself.

Posted on May 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1998 mercury mountaineer wont shift out of park


Could be the brake switch, or the shift lock solenoid.
You should be able to shift out of park by turning the key to unlock the shifter but all the way to the on position. Make sure the parking brake is set first.

Feb 21, 2015 | 1998 Mercury Mountaineer

1 Answer

Poping sound from rear end


it can be your parking brake shoe in the rear that is inside the rear rotor. there is a brake pad and a parking brake shoe in the rear

Dec 22, 2012 | 2000 Mercury Mountaineer

1 Answer

My 2002 mercury mountaineer have no problem going forward but when i put it in reverse the back wheels locks and give off a burning rubber smell .


check the parking braske that is inside the rear rotor. the back brakes has brake pads and a parking brake shoe

Dec 19, 2012 | 2002 Mercury Mountaineer

1 Answer

My 2002 mercury mountaineer have no problem going forward but it seen like when i put it in reverse the back wheel lock and it out out a funny smell


It sounds like you have a loose brake shoe inside one of your rear axle brake drums. You will have to remove the rear wheels and brake drums to find out for sure.

Dec 19, 2012 | 2002 Mercury Mountaineer

1 Answer

How do you adjust the parking brake on the 1997 sable


they r a self adjusting cable....if ur sable has rear drum brakes then adjust the rear shoes...if it has rear disc brakes then u have a faulty rear brake caliper..the parking brake system is also inside the rear brake calipers

Jul 16, 2011 | 1997 Mercury Sable

1 Answer

How to remove rear rotor after wheel is off


Disc Removal
  1. NOTE: When removing the rear brake disc (2C026) in this procedure it is not necessary to disconnect the hydraulic lines.
    Remove the rear disc brake caliper (2552).
1.Remove the brake caliper bolts (2W303).
2.Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2C220aca3301.gif
  1. NOTE: If the rear brake disc binds on the rear parking brake shoe and linings, remove the adjustment hole access plug and contract(push back to allow clearance) the parking brake shoe and lining.
  2. Remove the rear brake disc.

Feb 11, 2010 | 1998 Mercury Mountaineer

1 Answer

Rear brake rotor replacment


206-04: Rear Disc Brake 2000 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Disc Removal
  1. NOTE: When removing the rear brake disc (2C026) in this procedure it is not necessary to disconnect the hydraulic lines.
    Remove the rear disc brake caliper (2552). For additional information, refer to Caliper in this section.
  2. Disconnect the brake hose.
  3. Remove bolt.
  4. Disconnect the rear wheel brake hose (2A442).
  5. Remove the copper washers and plug the brake hose.
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not remove the guide pins or guide pin boots unless a problem is suspected. The guide pins are meant to be sealed for life and are not repairable. Use Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A (Motorcraft WA-10) or an equivalent silicone compound meeting Ford specification ESE-M1C171-A for re-lubing the caliper slide pins. Other greases can swell the guide pin boots, resulting in contamination and accelerated corrosion or wear of the caliper slide pin mechanism.
    Remove the rear disc brake caliper (2552).
    1. Remove the brake caliper bolts (2W303).
    1. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2C220).
  1. Inspect the rear disc brake caliper for leaks.
    • If leaks are found, disassembly is required. Refer to Caliper in this section.
  1. NOTE: If the rear brake disc binds on the rear parking brake shoe and linings, remove the adjustment hole access plug and contract the parking brake shoe and lining.
    Remove the rear brake disc.
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use a hub-mount brake lathe if necessary to machine the rear brake disc.
    Measure the rear brake disc, and resurface as necessary. Install a new rear brake disc if beyond specification.

Mar 28, 2009 | 2000 Ford Explorer

1 Answer

HOW TO FIX THE PARKING BREAK ON A 1997 MERCURY MOUNTAINEER


most likely the parking brake shoes need to be replaced. they have a tendency to rust and break off and the brake wont hold

Feb 25, 2009 | 1997 Mercury Mountaineer

1 Answer

Park Brake Adjustment



Park Brake Adjustment (Disc Brake)

Tools Required

j 21177-A Drum-to-Brake Shoe Clearance Gage

Park Brake Shoe Adjustment

Caution: Refer to Brake Dust Caution.

Important: The park brake shoes must be adjusted before the park brake cable tension is adjusted.Set the J 21177-A so it contacts the inside diameter of the rotor
  1. Position the J 21177-A over the shoe and the lining at the widest point.
  2. Turn the adjuster nut until the lining just contacts the J 21177-A. Park brake shoe to brake rotor clearance: 0.6604 mm (0.026 in)
  3. Repeat steps 1-3 for the opposite side.
Park Brake Cable Tension Adjustment

Important: Before you adjust the park brake cable tension, verify that the park brake shoes are adjusted to provide a clearance of 0.6604 mm (0.026 in) and the rear disc brake rotors are installed.

  1. Verify the self adjuster lock-out pin has been removed.
  2. Fully apply and release the park brake pedal 3 times.

Feb 22, 2009 | 2007 GMC Sierra C/K2500

1 Answer

Parking brake adjustment


   You need to knock out the access hole in the backing plate . Not and easy job. If it just quit working the shoes have most likely separated from the linings and need to be replaced.

Jul 07, 2008 | 2003 Mercury Mountaineer

Not finding what you are looking for?
1999 Hyundai Accent Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8575 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...