Question about 2004 Nissan Altima

Open Question

How to replace hood rod retainer clip

How to remove old hood rod retainer clip

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lock barrel has gone in to the door


remove door panel and at bottom of door frame will be lock retaining clip and actuator rods if the clip is broken most auto stores carry them bring with you for correct size --if lucky all but the retaining clip is on bottom and lock can be reinserted and clip replaced

Jul 12, 2016 | 2005 Kia Sorento

1 Answer

How to replace wiper motor


Most wiper units are attached to the firewall. Some have removable plastic cover valances which allow access to the wiper blade rods (called a wiper transmission). Others have some slack in the wiper rods with enough play to allow for you to remove a retaining clip holding the parts to the motor. Do not have butter fingers here. Do not drop the retaining clip. Just remove the wiper mounting bolts and slide out the motor.

Aug 13, 2015 | 1993 Mercury Villager

1 Answer

Brake booster from 1997 vw jetta removal instructions


Hi. Ther is a special tool for this, but it is clumsy and difficult. The plastic retainer is cheap enough to just break it out and fit a new one in place. fit it into the pedal first then clip the rod in otherwise the rod breaks through the clip before it seats into the pedal.

Jan 18, 2014 | 1997 Volkswagen Jetta

1 Answer

Removing low beam bulb on 05 subaruoutback


Whether they become damaged in an accident or simply burn out over time, your Subaru Outback's headlights may eventually need to be replaced. Fortunately, once you've purchased the right replacement bulb for your model year, performing the repair yourself is relatively easy. These instructions only apply to Outback models made after 2000.

  1. Undo the clips on the air intake ducts using a screwdriver and remove the duct from the engine compartment (driver's side bulb removal only.)

  2. 2

    Loosen the secured clip on the washer tank with a screwdriver and slide the tank horizontally to allow easier access to the headlight assembly (passenger's side bulb removal only.)

  3. 3

    Turn the bulb cover counterclockwise and remove it from the assembly.

  4. 4

    Disconnect the headlight electrical connector and undo the assembly retaining spring.

  5. 5

    Pull the old bulb directly out of the socket and replace it with the new one. Press the retaining spring back into place and reattach the electrical connector.

  6. 6

    Replace the bulb cover, and then turn on the engine. Test the new headlight to make sure it works before replacing the air intake duct or the washer tank and closing the hood.

    Replacing the High-Beam Bulbs
  1. 1

    Undo the clips on the air intake ducts using a screwdriver and remove the duct from the engine compartment ( drivers side bulb removal only.)

  2. 2

    Loosen the secured clip on the washer tank with a screwdriver and slide the tank horizontally to allow easier access to the headlight assembly (passenger's side bulb removal only.)

  3. 3

    Disconnect the headlight electrical connector and undo the assembly retaining spring.

  4. 4

    Turn the headlight bulb counterclockwise and pull it out of the socket.

  5. 5

    Reinstall the new bulb, replace the retaining spring and reconnect the electrical connector.

  6. 6

    Test the new headlight to make sure it works before replacing the air intake duct or the washer tank and closing the hood.

Sep 14, 2012 | Cars & Trucks

1 Answer

How to replace license plate lights


    Follow the Steps on how to replace license plate light on your car.

    1. Open the trunk and locate the trunk liner retainer clips.Use the Phillips head screwdriver to loosen the center plastic screw of the retainer clip about 1/4 turn, just enough to raise the head of the screw from the base of the clip. Pull the screw up, and lift the clip out of the liner. Use a flathead screwdriver to help pry it out. Remove enough of the clips to allow access to the license plate light sockets. Pull the liner back.

    2. Remove the emergency trunk release handle by popping off the top cover of the handle. Use the needle nose pliers to gently squeeze the prongs on the shaft, while removing the handle.

    3. Unplug the wire harness from the license plate light bulb socket the release clip on the side of the outlet.Twist the license plate light bulb socket 1/4 turn counterclockwise, using the needle nose pliers again. Do not apply too much pressure to the pliers; you may damage the socket.

    4. Remove the bulb from the socket, and replace it with a new one.

    5. Replace the socket into the socket assembly, and plug the wire harness back in. Test the bulb by turning on the lights of the Corolla, then turn them off again.

    6. Replace the trunk emergency release handle, and replace the hood liner and the retainer clips. Remove the old bulb and tools, and close the trunk.

Dec 22, 2010 | 1995 Toyota Corolla

1 Answer

How does one install a front grill on a chev equinox 2006 lt


Open the hood of your Equinox and raise the support rod to prop it out of the way. Locate the retaining clips around the front grille of your truck. Pull each of the eight retaining clips straight up off the grille. Pull the grille out away from the front of the truck.

Aug 13, 2010 | 2006 Chevrolet Equinox

1 Answer

Where is windshield wiper motor for 1992 mercury grand marquis


1992-98 Vehicles
  1. Disconnect the negative battery cable.
  2. Remove the rear hood seal. Remove the wiper arm assemblies by raising the wiper blade off the windshield. Move the slide latch away from the pivot shaft and slowly lower the arm onto the latch. This unlocks the arm from the pivot shaft and holds the blade off the glass. Pull the arm from the pivot shaft.
  3. Remove the cowl vent screws and disconnect the washer hoses from the washer jets.
  4. Detach the electrical connectors from the wiper motor.
  5. Remove the wiper assembly attaching screws, lift the assembly out and disconnect the washer hose.
  6. Unsnap and remove the linkage cover.
  7. Remove the wiper module assembly retaining bolts and remove the module from the vehicle.
  8. Remove the linkage retaining clip from the motor operating arm by lifting the locking tab and pulling the clip away from the pin.
  9. Remove the motor retaining screws and remove the motor from the vehicle.
  10. The installation is the reverse of the removal.

ad37f8d.jpg

Fig.: Lift up to release the clips and remove the hood-to-cowl weather strip


ca6ea0f.jpg

Fig.: Remove the cowl panel-to-firewall retaining clips



Remove the driver's side then the passenger side cowl panel from the vehicle


d57f264.jpg



Fig.: Detach the electrical connector for the wiper motor

Release the wiper motor retaining clips and remove the cover from the vehicle


ffed3a6.jpg



Fig.: Remove the wiper module assembly retaining bolts and remove the module from the vehicle


412221d.jpg



Fig.: Remove the wiper motor retaining bolts and ...


46edc09.jpg


Fig.: ...remove the wiper motor from the vehicle




Hope helps (remember comment and rated this).

Aug 02, 2010 | 1992 Mercury Grand Marquis

1 Answer

How do you take the grille off of a 1996 isuzu trooper 2




Trooper
See Figures 3, 4 and 5


a06490f.jpg
Fig. 3: Front grille assembly-1984-94 Trooper


e8688ea.jpg
Fig. 4: Front grille assembly-1995-96 Trooper


57fd329.jpg
Fig. 5: Retainer clip used to secure the front grille
  1. Raise the hood and support it with the prop rod.
  2. On 1981-94 models, remove the retainer screws from around each headlight.
  3. Remove the retainer screws from the corners and center of the grille.
  4. Using a small prytool to press the tab on each of the grille retainer clips at the top of the grille upward while pulling the grille away from the radiator support.
  5. When all the tabs have been released, lift the grille up slightly and out to remove.
To install:
  1. Engage the lower portion of the grille into the radiator support.
  2. Carefully push the grille toward the radiator support, making sure the retainer clips align with their respective mounting hole. Once all the holes align, press the grille and retainer in until it clicks into position.
  3. Install the retainer screws from the corners and center of the grille.
  4. On 1981-94 models, install the retainer screws around the headlight.

Hope helps (remember rated this).

Jul 09, 2010 | 1996 Isuzu Trooper

1 Answer

How do I remove the inside door panel of a 2001 AU11 Ford Fairmont to get at the manual door cable?


Standard Trim Disconnect the remote rod-to-lock knob assembly prior to lifting off the housing plate, to avoid possible damage to the lock knob assembly.
  1. Remove the inside door handles by unfastening the retaining screws.
  2. Remove the armrest. Tag and disconnect all electrical connectors.
  3. Remove the mirror remote control bezel nut and bezel.
Before you proceed to the next step, carefully inspect the door panel to make sure that all the retaining screws have been removed.
  1. Using a wooden spatula or panel puller (available at most automotive parts stores), pry around the trim panel putting pressure at the door trim clips. NEVER PRY BETWEEN THE CLIPS.
  2. Installation is the reverse of removal. When installing the trim panel, align the clips in the panel with the holes in the door, then apply pressure on the panel over the clip until the clip snaps into place.

Deluxe Trim Disconnect the remote rod-to-lock knob assembly prior to lifting off the housing plate, to avoid possible damage to the lock knob assembly.
  1. Disconnect the negative battery cable.
  2. Remove the screws from the door handle cup.
  3. If the car has an armrest courtesy lamp(s), remove the lens, then remove the bulb and wiring. Remove the pull cup.
  4. Reach through the pull cup opening and disconnect the remote lock rod from the lock knob.
  5. Remove the retaining screw and the remote mirror bezel nut from the power window regulator housing switch plate. Raise the plate to expose the window switch and power door lock switch and disconnect them.
  6. Remove the retaining screws from the armrest assembly.
Before proceeding to the next step, carefully inspect the door panel and make sure all the retaining screws have been removed.
  1. Using a wooden spatula or a panel puller (available at most automotive parts stores), pry around the trim panel putting pressure at the door trim clips. NEVER PRY BETWEEN THE CLIPS.
  2. Disconnect the speaker wiring and lift off the panel.
  3. Installation is the reverse of removal. When installing the trim panel, align the clips in the panel with the holes in the door, then apply pressure on the panel over the clip until the clip snaps into place.

May 06, 2010 | 1983 Ford Fairmont

2 Answers

How do you change the front light on the drivers side.


since i've not personally had a chance to get my hands on this model of vehicle yet, i'm going to make an educated guess based on how it is done on the 02 sierra, since both are gm products. On the sierra there are 2 rods right at where the headlights are under the hood. Remove those rods to release the light bezels, the bezels should be able to be easily removed. from there just remove the bulb from its' socket, disconnect it from the wire, put in the new one and reassemble. Hope this helps

Mar 10, 2010 | 2005 Chevrolet Equinox

Not finding what you are looking for?
2004 Nissan Altima Logo

Related Topics:

167 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14251 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...