Question about Volkswagen Caddy

Open Question

How to disassemble the shark sk460

How to take the handle off

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Signal handle wont snap back after making a turn


You will basically have to replace the cancel cam to correct this problem. Some disassembly of the steering wheel components may be required and if the vehicle is equipped with air bags it is probably better left to a professional.

Apr 13, 2014 | Chevrolet Lumina Cars & Trucks

1 Answer

My 06 dodge ram tailgate will not release. how do i fix it?


Then you must disassemble the tailgate and check the linkages to see what is malfunctioning with the exterrior handle. Sometimes the ears on the handle itself breaks.

Nov 28, 2011 | 2006 Dodge Ram 1500

1 Answer

I need to replace rear passenger outsaide door handle, do I need to take off inside panel to do so? Is this a difficult task?


yes you do and no it isn't, Just use care once you get to the handle to watch for the clips that hold the connecting rods if your model has them,, other than that a couple of screws and your home free,, I would make sure I have the replacement handle in hand ,, that way you can see what hold downs it has prior to disassembly

May 15, 2011 | 2005 Mercedes-Benz Mercedes Benz E320 Cdi

1 Answer

On my 1986 Toyota Celica, the little button that you press on the handle to wash the windows is pressed in and stuck. How do I disassemble the handle to find out what is wrong? Thank you!!!


take a screwdriver handle and knock along the side and see if you can knock it loose. Years of grime are in the hole and making the button stick. maybe spray some windex down the hose and see if it will loosen. I dont think it comes apart.

Dec 17, 2010 | 1991 Toyota Celica

1 Answer

How to remove a fan shroud


the fan shroud is actually a full station unit it houses coolant and winshield fluid, to remove it you must first locate all the bolts that connect the top and bottob portion the unit disassembles like a sharks mouth look down the sides the bolts will be on the sides and rad cradle(top) they are 10 mil.

Dec 12, 2009 | 1999 Dodge Dakota

1 Answer

04 sequoia will not unlock on rear door... handle was replaced and after 2-3 times will not open.


This is a very common problem with the early model Sequoias. The handle assembly has a poor design.

There is an extended thread about this problem on www.tundrasolutions.com. Go to the Sequoia section. There are several threads that give step by step instructions on disassembling the door and repairing the lock and handle. There are also several suggestions about steps to take to keep the problem from recurring.

Oct 20, 2009 | 2004 Toyota Sequoia

1 Answer

Driver side door handle pop off. Can it be repaired


A piece of metal probably broke. You likely will need a new door handle installed. This requires disassembly of the inside of the door.

Oct 17, 2009 | 2001 Buick Lacrosse

3 Answers

95 Toyota Camry All outside handles broken off


I had the same issue with both the inside and outside door handles of my '95 Camry LE.

They are not too expensive. $15-20 each, sometimes you can find a set of four for $50. Try Amazon.com, that's where I just bought my new handles.

Replacement is time-consuming, but relatively easy to figure out. If you have the Haynes manual for your car, it will describe the steps required to disassemble the door paneling and replace the handles.
Have a Phillips AND Flathead screwdriver handy. You will need both to disassemble your door.

Good luck!

Feb 14, 2009 | 1995 Toyota Camry

1 Answer

Removing outer door handle on 1998 honda civic


I usually get a haynes manual for this problem it will tell you the proper tools and procedure with out needing an automechanic standing by your side pep boys or your local auto store should sell these manuals hope this helps

Jan 03, 2009 | 1998 Honda Civic

1 Answer

Installing the emergency brake release cable in the dash


put the end in the release handle first then attach to dash cover.

Jun 05, 2008 | 1998 Plymouth Voyager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

237 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

yadayada
yadayada

Level 3 Expert

77169 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8732 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...