Question about 1999 Land Rover Range Rover

1 Answer

What if i take off the front drive shaft - 1999 Land Rover Range Rover

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 603 Answers

You will leak fluid and go nowhere. GOOD LUCK FRIEND.

Posted on Nov 28, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

What is a cv shaft


Dear Dianne,
Under the front hood of your Honda is a motor or it is also called an engine.
The engine is hooked or fastened to a large container called a transmission, which is also under the front hood.
In order to get the car to move, there are 2 steel drive shafts going from the transmission to the front wheels.
These drive shafts are about one to 2 feet long, and each one drives a front wheel. That is why there are 2.
These steel drive shafts have a large joint at each end of them, so you see why there are 4 joints.
The joints attach to the wheel on one end and the transmission on the other end.
These 2 steel drive shafts are called cv shafts because they have a CV joint at each end, and these CV joints are a part of the shaft assembly.
The CV shafts "transfer" the movement of the engine to the wheels.

Dec 03, 2015 | 2007 Honda CR-V

1 Answer

Front diff.seal leaks


Remove the front drive shaft remove the drive yoke off the pinion shaft remove the old seal install new seal install front drive shaft. PS check pinion bearing play before removing drive yolk. if it is loose then you might also need bearings

Oct 21, 2015 | Ford Explorer Cars & Trucks

1 Answer

Tractor case 585xl front diff not driving. Front shaft drives but not wheels.



I am thinking that you have a broken/ stripped drive spline on a front axle. If you have reduction gears in the hubs , it may be stripped teeth on a gear. If you jack up one front wheel and turn the drive shaft that wheel should turn. IF so repeat the procedure for the other wheel and if it doesn't turn like the other side then that is the side with the problem

Dec 17, 2014 | Cars & Trucks

1 Answer

Cv boot failure


The best thing to do is completely remove the front drive shaft (assuming you are talking about the front CV boots).
1) Jack up the front end of the vehicle.2) Remove front wheel(s), track rod ends and slacken [don't remove completely just yet] the centre hub nut and remove split pin.3) With the gear in neutral, and using an appropriately sized round punch and hammer, punch out the location pin from the drive shaft where the drive shaft meets the gearbox output shafts.4) With the assistance of a flat screwdriver, lever and pull the drive shafts off the gearbox output shafts and let them drop down. 5) Using a rubber mallet, hammer the drive shaft through the front hub. You kept the nut on the end of the shaft initially so as to prevent damage to the drive shaft threads during hammering. This nut will have to be backed off and eventually removed as the shaft slides through and out of the hub unit.
With the entire shaft removed from the vehicle:
1) Cut off or slacken and remove any rubber boot retaining clips.2) slide the rubber boot(s) towards the centre of the shaft.3) Remove the inner joint first by using a small, flat screwdriver to flick out the retaining wire from the inner lip of the joint. (Keep this wire)4) Slide off inner joint cup and clean.
5) Locate the spring clip from the inner end of the shaft and carefully remove without over-stretching. if you have no replacement.
6) Slide off inner C.V. joint, and clean.
7) Remove damaged boot(s), clean all components, re-grease with LM grease and replace.
8) Reinstallation is the opposite of removal steps.


Note: Take care when re-installing drive shaft to gearbox output shaft. This will usually only align to a single position. Before tapping retaining pin back into place, visually inspect alignment of the shaft's holes. You can use your round punch to help align the holes before re-installation of the retaining pin.


Tip: With the removal of the front drive shafts, it may be a good opportunity to also replace front gearbox output oil seals and front wheel bearing-drive shaft dust seals. These are fairly inexpensive and may prolong the life of components as well as reduce the need for repetitive removal of parts.

Nov 03, 2012 | 2003 Subaru Baja

3 Answers

Is there a drive shaft


no, there is no "drive shaft" on a 94 oldsmobile. It is front wheel drive. you have a CV shaft from trans to left front wheel and a separate CV shaft from trans to right front wheel.

Jan 14, 2011 | 1994 Oldsmobile Cutlass Ciera

2 Answers

Front drive shaft on Jeep Grand Cherokee


yes but make sure you don't in gauge the front axle

May 19, 2010 | 2000 Jeep Grand Cherokee

1 Answer

I have a 93 sub with 4 wheel drive. front drive shaft truns all


Yes the front wheels will spin the front shaft but the shaft is not engaged until 4 wheel drive is engaged.

Lone99star

Jan 05, 2010 | 1993 Chevrolet Suburban

1 Answer

How to replace front drive shaft ?


Mark the drive shaft postion to the transfer case and front axle. Remove the bolts/straps from the transfer case and front axle pinion that hold the drive shaft in place. Remove drive shaft. You may have to drop the exhaust pipe for access.

Jun 02, 2009 | 1997 Dodge Dakota

2 Answers

Worn front drive shaft


no only the front axles rotate.

May 30, 2009 | 1998 Chevrolet K1500

1 Answer

Front axle - front drive shaft Toyota tacoma 1998 4x4


more than like have a broken axle shaft, un hook the rear drive shaft and put it in 4wd if it wont move then you know you got a broken axle shaft or spider gears broke in the pumpkin

Dec 09, 2008 | 2007 Toyota Tacoma

Not finding what you are looking for?
1999 Land Rover Range Rover Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...