Question about 2009 Chevrolet Impala

1 Answer

Install new bumper pad lower and upper on 99 ford expedition

Upper and lower just pry off old and push on new pad ???

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 444 Answers

They have little arrow head type devices that push into slots in the metal bumper, to get the old ones off you can go in from behind and pinch the arrow head things with pliers and push the out but really if you are just going to throw the old pad away just pry them up and they will come off. the new bottom one may be difficult and you will think it is too short but really it will go on. start in the middle and work your way outward. you will need a rubber hammer to make the arrowhead clips sink in to the proper depth to open into the slots

Posted on Jan 04, 2015

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 340 Answers

SOURCE: I have installed new upper and lower hinges for my

most of these cars the only part you can change is the pins if your are bolted on you can adjust loosen the bolts one hinge at a time to adjust... when changing a door with live hinges you should mark ware the old hinges were so you can put the new hinges in the same place
if you car has welded hinges you have to bend the door at the hinge or door support ( its not as hard as it seems)

Posted on Mar 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the front roters


Remove the wheel, Remove the brake calipers, simply grab and pull the rotor off. Install new rotor, then push the piston back into the caliper a little ways, or all the way if installing new pads. This can be done using the old brake pad and a c-clamp to push the piston down. Install new pads and install the caliper. Install the wheel and torque to atleast 80 foot pounds. I torque mine to 100. Torque is important so as not to warp the new rotor.

Aug 16, 2013 | 2006 Ford Expedition

1 Answer

1999 Expedition Keypad Reset


we have 2000 exped. and seller didnt know code. Heard that it is located in the rear of the truck where the bumper jack is... and i couldn't figure it out. Went to dealer...yikes!! and paid 50.00 to have it reset to factory. had to weigh fustration...locked in keys... and inconvience against my time of not figuring it out.... took 15 minutes at ford....

Nov 07, 2011 | 1999 Ford Expedition

1 Answer

How do I replace the turn signal multi-function switch in my 1998 Ford Expedition


SECTION 211-05: Steering Column Switches 1998 Expedition/Navigator Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 02/11/2000 Multifunction Switch Removal
  1. Disconnect the battery ground cable (14301).
  1. Remove the ignition switch lock cylinder (11582).
    1. Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
    1. Insert a punch through the hole in the lower steering column shroud and push the ignition switch lock cylinder release tab while pulling out the ignition switch lock cylinder.
    gj0845a.gif
  1. Twist the tilt wheel handle and shank (3F609) and remove.
    gj0846a.gif
  1. NOTE: Move gear selector to lowest position to access steering column opening cover.
    Release the four clips and remove the steering column opening cover.
    gj0847a.gif
  1. Remove the upper and lower steering column shrouds.
    1. Remove the three screws.
    1. Remove the lower steering column shroud.
    1. Remove the upper steering column shroud.
    gj0976a.gif
  1. Remove the multi function switch.
    1. Remove the two screws.
    1. Disconnect the electrical connectors.
    1. Remove the multi function switch.
    gj0848a.gif
Installation
  1. NOTE: When the battery (10655) is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
    To install, reverse the removal procedure.
    gj0850a.gif

2010&c18=modelyear&c20=n130593&c35=wsm%2cmultifunction%20switch%2cswj%2c211-05%2cremoval%20and%20installation&s=1366x768&c=32&j=1.3&v=y&k=y&bw=995&bh=405&ct=lan&hp=n&[aqe]

Mar 08, 2011 | 1998 Ford Expedition

1 Answer

My hazard lights work, on my 1999 expedition xlt, but my turn signal lights do not. Im not sure if I need to replace the flasher or the relay. If its the flasher, where is the flasher located and where...


This is a common problem for the turn signal switch itself. Try used. You will notice in the instructions to remove the steering wheel. Don't. The removal of the ignition switch is also not necessary. Remove the screws at the bottom of the column where it shows and take a screw driver and pry the other side up to see the 2 screws (torx, or star bits) to remove. This will only take about 20 minutes to perform.

  1. Disconnect the negative battery cable.
  2. Remove the 4 retaining screws from the lower column shroud and remove the upper and lower shrouds.
  3. Remove the 2 retaining screws from the multi-function switch and unplug the 2 wiring connectors.
  4. Remove the switch.

To install:
  1. Install the multi-function switch.
  2. Tighten the 2 retaining screws and attach the 2 electrical connectors.
  3. Install the upper and lower column shrouds. Tighten the 4 retaining screws.
  4. Connect the negative battery cable.

F-150, F-250, Expedition, Navigator and 1999-00 Super Duty Models


0900c152801e597e.jpg

Fig. Fig. 1 Turn the ignition switch to the RUN position and push the lock cylinder release pin with a suitable punch while ...



0900c152801e597f.jpg

Fig. Fig. 2 ... pulling out the lock cylinder



0900c152801e5980.jpg

Fig. Fig. 3 Remove 3 steering column shroud retaining screws and ...



0900c152801e5981.jpg

Fig. Fig. 4 ... remove the upper and ...



0900c152801e5982.jpg

Fig. Fig. 5 ... lower steering column shrouds



0900c152801e5983.jpg

Fig. Fig. 6 Remove the switch retaining screws, lift the switch assembly up and ...



0900c152801e5984.jpg

Fig. Fig. 7 ... detach the switch electrical connectors to remove the switch

  1. Disconnect the negative battery cable.
  2. Remove the ignition key and tumbler as follows:
    1. Turn the ignition switch to the RUN position.
    2. Push the lock cylinder release pin with a suitable punch while pulling out the lock cylinder.

  3. If equipped, twist off the tilt wheel handle and remove.
  4. Remove 3 steering column shroud retaining screws and remove the upper and lower shrouds.
  5. Remove 2 self-tapping screws that retain the combination switch to the steering column casting. Disengage the switch from the casting.
  6. Detach the electrical connectors, being careful not to damage the locking tabs and the shift position indicator cable.

To install:
  1. Connect the combination switch electrical harness connectors ensuring that the connectors are fully engaged. The wiring for the switch is to be routed under the shift position indicator cable.
  2. Install the combination switch with 2 self-tapping screws. Tighten to 19-25 inch lbs. (2-3 Nm).
  3. Install the upper and lower steering column shrouds. Install the retaining screws and tighten to 9 inch lbs. (1 Nm).
  4. If equipped, install the tilt wheel handle ad tighten to 44 inch lbs. (5 Nm).
  5. Install the ignition key and tumbler assembly.
  6. Connect the negative battery cable.
  7. Check the steering column and combination switch for proper operation.

Feb 12, 2011 | 1999 Ford Expedition

1 Answer

How can i change the rear brakes pads?


1.Remove the cap from the brake fluid reservoir

2.Loosen the wheel nuts then raise the vehicle and remove wheel

3.Push the piston back into the bore to provide room for the new brake pads.A C-clamp can be used to accomplish this As the piston is depressed to the bottom of the caliper bore the fluid in the master cylinder will rise.Make sure is doesnt overflow.If necessary drain off some of the fluid. 4.Before removing anything,spray the disc,and brake pads with brake system cleaner dont use compressed air 5.remove the caliper mounting bolt,the banjo fitting for the brake hose shouldnt be disconnected unless you are removing the caliper or hose replacement

6.Swing the caliper up and secure the caliper up towards the spring with a piece of wire then remove the lower and upper anti-rattle springs.Remove the outer brake pad and shim then remove the inner brake pad ans shim(s)

7.Remove and inspect the upper and lower pad retainer clips,the pad retainer clips should fit snugly in the caliper mounting bracket;if they dont,replace them.Apply thin film of high-temperature grease to the retainer

8.Apply anti-squel compound to the back of pads install the new inner pad and shim(s) make sure the "ears" on the upper and lower ends of the pad are fully engaged with their respective grooves and the pad retainer clips

9.Install the new outer pad and shim if new pad has no shim take the old shimoff the old pad and install it on the new outer pad.Install the upper and lower anti-rattle springs

10.Clean off the caliper pin and coat it with high-temperature grease.Lubricate the lower caliper pin with grease too thenswing the caliper down over the disc and new pads (if the piston hits the inner pad depress the piston further into the caliper bore with your c-clamp

11.Install the mounting bolt and tighten it to the torque specifications (44-63) 99 and earlier models (51-55)00 and later models
12.Put the wheel back on and tighten lug nuts

Oct 05, 2009 | 1998 Hyundai Elantra

1 Answer

Ford Expedition rear bumper is lower


Either someone backed into it or you have a suspension issue. If you have air suspension the light should be on indicating a malfunction. If you do not have air suspension you may have collapsed spring if nothing else is broken

Sep 19, 2009 | 2000 Ford Expedition

1 Answer

I AM TRYING TO INSTALL A THERMOSTAT ON A 99 FORD EXPEDITION AND I AM AN AMETUER WHEN IT COMES TO REPAIRS ON AUOTMOBILES..I NEED A BOOK WITH PHOTO DESCRIBTION OF THE PARTS


ok first locate top radiator hose follow from radiator to block theres two bolts holding water neck remove the bolts and theres the thermostat. make sure you put the thermostat the way you pull the old one. to install repeat steps backwards.

Jul 06, 2009 | 1999 Ford Expedition

2 Answers

Changing rotors and breaks


When you replace the pads you have to retract the pistons into the bore. As the pads wear they stay extended from the brake caliper. The new thinkness of the pads will not allow the pads the slip over the rotors until you retract the pistons. Your pistons may be the type that have to be turned back into the bore.Good luck.

Mar 12, 2009 | 1998 Ford Expedition

1 Answer

Brake replacement


take the brake caliper off, this is the part that holds and moves the brake pads thare will be 2 bolts holding it on ,one on top one on bottom. after taking bolts loose you may half to pry the caliper up and off brake rotor. once this is done remove old pads and use a brake caliper piston retraction tool to push the piston back into the caliper. you can get this tool at your local parts store or use a C clamp with one of the old brake pads to push it back.install new brake pads and install caliper .after completion make sure you pump the brakes till you get a good pedal before moving vehicle

Dec 26, 2008 | 1990 Ford Bronco

2 Answers

Brake rotors


They get rusted to the hub. Try heat and a large hammer.

Nov 25, 2008 | 2003 Ford Expedition

Not finding what you are looking for?
2009 Chevrolet Impala Logo

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...