Question about Cars & Trucks

1 Answer

How to bleed power steering from a 94 Holden TF rodeo 2.8 Diesel

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 71 Answers

Fill the reservoir and start the engine. turn the steering wheel from side to side fully three or four times. now you have done the bleeding. so again see the reservoir and add oil if necessary

Posted on Feb 10, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: 1994 isuzu holden rodeo injection timing adjustment

try u-pull our patrs

Posted on Sep 12, 2008

snownbird33
  • 120 Answers

SOURCE: Holden 94 rodeo petrol

Good Day
Vale clearance cold
intake .006 in (.15 mm)
exhaust .010 in (.25 mm)

Timing
1. With transmission in Neutral or park, start engine and warm to normal operating temp. turn eng,and all accessories off. connect Tachometer. Connect timing light to no 1 spark plug wire.

2. Disconnect and plug fuel vapor canister purge hose and EGR vacuum hose. Start and ensure idle is 900 RPM. adjust idle as required. Check ignition timing ( 12 @ 900)

3. If adjustment is required, loosen distributor hold down bolt and turn until timing is within specification. Tighten distributor hold down bolt and recheck timing. adjust idle speed as required.

hope this helps

Cheers

Posted on Sep 30, 2008

  • 1 Answer

SOURCE: holden rodeo turbo diesel 2007

I KNOW SOMEONE WITH EXACT PROBLEM.
CONTACT ME ON 0400432502 U CAN SHARE YOUR INFOS.
TA21

Posted on May 07, 2009

stevenhurc
  • 450 Answers

SOURCE: reprogramming remote and key

if its early 05 round heart shaped remote it needs programming into system at dealer with Tech2
later 05 to 07 had square (rectangle) shaped remote
1.2 ID Code Additional Registration
Note: This procedure will add additional remotes to the Keyless Entry Control Units memory. A total of 4 remote transmitters may be programmed into the Keyless Entry Control Units memory. When a total of registered and newly registered remotes exceed 4, the oldest one shall be erased.
Step Action
1 Note: Make sure that all the doors are closed and unlocked. Insert the ignition key into the ignition switch.
Open the driver's side door.
2 Turn the Ignition key to the “ON” position and then to the “LOCK” position three times
(The key should remain in the “LOCK” position)
Note: This step must be carried out within five seconds.
3 “CLOSE” and “OPEN” the driver’s doors once (Leaving the driver’s door in the “OPEN” position)
Note: This step must be carried out within five seconds after step 2 is completed.
4 Wait for 8 seconds (This wait time is critical)
5 Turn the Ignition key “ON” and then to the “LOCK” position once and turn key to the “ON” position (The key should remain in the “ON” position)
OR on/lock once
Note: This step must be carried out eight seconds after step 3 is completed.
6 “CLOSE” the driver’s door
The HAZARD lights should flash 3 times (This acknowledges the Keyless Entry Control Unit has entered programming mode)
7 Operate the lock or unlock button of the transmitters to be programmed; a flash of the HAZARD lights indicates the remote has been successfully programmed into the control unit
8 The HAZARD lights will flash approx 4 seconds after pressing the remote button to indicate the Keyless Entry Control Unit has exited programming mode.

Posted on Jun 21, 2009

  • 1 Answer

SOURCE: Intermitten loss of throttle car

you need to have the throttle body cleaned out or replaced

Posted on Apr 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is 1995 holden rodeo high beam switch located


http://www.ebay.com.au/itm/Indicator-High-Beam-Stalk-Switch-Rodeo-TF-1988-97-Holden-TFR-TFS-Blinker-Turn-/261941117019

it will be on the indicator stalk from the part link above. probably pull or push the stalk gently forward or towards you .

Jun 08, 2016 | Holden Cars & Trucks

1 Answer

Why can't find water trap on rodeo second generation TF 1988 2003 Holden rodeo tray top


Not unless it was fitted after market. to make sure trace the fuel line from the fuel filter back to the tank.

Jul 08, 2014 | Holden Rodeo Cars & Trucks

1 Answer

Can i replace my 4bj1t engine with a 4jg2t in 96 tf rodeo.


no it wont comply to emission laws and some wiring differences and a couple of minor issues are different

Aug 10, 2009 | 2000 Isuzu Rodeo

1 Answer

1998 Holden Rodeo TR series 5-speed manual 2WD


run the fault codes
look for ambient temp sensor or baro sensor problems

Jun 30, 2017 | 1992 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...