Question about 1997 Chevrolet Blazer
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: 98 chevy s10 blazer turn signal
Unplug the turn signal relay from the fuse box and start you engine. Does it still make that noise?
If yes... Put the relay back in, that is not the problem.
If No...Then the relay could be bad, replace it!
PLEASE RATE THIS SOLUTION! Thank You Very Much!
Posted on Nov 25, 2008
SOURCE: firing order for 97 chevy blazer
Firing order is 1-6-5-4-3-2. Distributor cap should be numbered. Number one cylinder is front on driver's side (3 and 5 follow on same side). Number 2 is front on passenger's side (followed by 4 and 6).
Posted on Apr 29, 2009
Since the 2000 chevy blazer is equipped with SRS (Saftey Restraint System), ie: Airbags, which is located in the steering wheel. In order to replace the turn signal switch you must remove the steering wheel. Therefore I would only highly advise you to take it to a dealer to have this done.
Posted on Oct 07, 2009
On 95-97 and 1998, both the turn signal and hazard flashers are located behind the lower dashboard trim just to the left of the cigarette lighter. You can not get to it without taking apart the trim (stupid design). Or you have to drill a 2" diameter hole in the trim with a velcro cover so you would never have to do it again1999 and later it is under the glove compartment
to disassemble it without drilling
It's behind the panel to the left of the cigarrette lighter. You need a Torx 25 screwdriver and another screwdriver for those hex shaped screws, forgot the size. First unscrew the 2 Torx 25 screws beneath the steering wheel. Then unscrew the rest of those Hex screws on the bottom. The panels overlap, so be prepared for a lot of unscrewing. You do need to unscrew the middle black panel on the bottom, right beneath the cig lighter. It's held by two Hex shaped screws, one on each side and are hard to unscrew. Also you need to remove your spare change sliding tray to unscrew the last hex looking screw. Once you pop your panel off, the turn signal flasher is the right one. The Hazard flasher is the left one. You can find a replacement part at Autozone, and DON'T get the $184 Flasher switch, all you need is the signal flasher. It's shaped like a cylinder with TWO prongs on it.
Posted on Nov 03, 2009
Drop the pan, odds are the shift solenoid is out, its located at the front of the trans on the driver side. I'm sure your check engine light is on that will comment about the timing/shift solenoid being bad. I had the same problem with mine. The solenoid had plastic coming out of the inside. To remove it you'll find a small C clip holding it in, just take a small screw driver and pull the clip out. The part cost me like $36 from my local dealership. And its a longer solenoid. I believe its the 3-2 downshift solenoid. I do have the part number if you need it.
Posted on Apr 25, 2010
Testimonial: "Thank you so much. I actually thought this was the problem, but i didn't know. Thanks again!! send me the part number"
Tips for a great answer:
Jul 29, 2013 | Cars & Trucks
Dec 04, 2012 | Cars & Trucks
Nov 29, 2012 | Cars & Trucks
Feb 07, 2010 | 1997 Chevrolet Blazer
Jan 06, 2010 | 1998 Chevrolet Blazer
Jan 02, 2010 | 1997 Chevrolet Blazer
Dec 31, 2009 | 1997 Chevrolet Blazer
Nov 01, 2009 | 1997 Chevrolet Blazer
May 02, 2009 | 1997 Chevrolet Blazer
Feb 19, 2017 | 1997 Chevrolet Blazer
11 people viewed this question
Usually answered in minutes!