Question about 2001 Ford Escort ZX2

Open Question

How to replace purge flow solenoid on a 2001 ford escor

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

warlock61
  • 659 Answers

SOURCE: i have a 1999 ford explore and i have to replace

it is fairly simple. the solenoid is located above the spare tire there is two hoses and a plug

Posted on Sep 11, 2009

  • 312 Answers

SOURCE: Getting an engine code 1450 on a 2003 ford

Did you check the block box connected to the vent solenoid? There's a hose that comes off it that appears to run nowhere, that's the fresh air vent. If it's blocked it won't allow air into the system which will set the trouble code. If that's clear, the vent solenoid itself is bad and needs to be replaced.

Posted on Jun 27, 2010

jturcotte
  • 8210 Answers

SOURCE: I need to repace a solenoid/small or no purge flow

The valve/solenoid is next to the battery--see picture below. here is the procedure from autozone.com. Let me know if you have questions.

Evaporative Emission (EVAP) Canister Purge Valve

  1. Disconnect the negative battery cable.
  2. Unplug the canister purge valve electrical connection.
  3. Tag and disconnect the vacuum lines from the valve.
  4. Remove the valve from the car.
To install:
  1. Install the valve and connect the vacuum hose.
  2. Attach the valve electrical connection.
  3. Connect the negative battery cable.

d5d7dc5.gif

Posted on Oct 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Evap


Inspect wiring and vacuum lines at the evaporative emission (EVAP) purge flow sensor and solenoid for pinched, cracked and/or loose connections. If everything looks OK, install a replacement EVAP canister purge flow sensor and solenoid assembly

Sep 28, 2012 | 1996 Ford Thunderbird LX

2 Answers

Common causes for codes p0441


getting code p441 could be caused by evap purge solenoid vacuum line loose leaking or restricted, evap purge solenoid faulty, evap purge vacuum line to canister leaking or disconnected,evap canister failed.

Feb 06, 2012 | 2001 Chrysler 300M

1 Answer

How do i fix code p1143 on 97 mustang


We are assumin gthat you are talking about DTC P1443 - Evaporative Emission Control System - Vacuum System - Purge Control Solenoid or Purge Control Valve fault.

Best guess without pinpoint testing would be the purge flow sensor. This is the most common failure for this code but can be caused by anything that would limit flow across the sensor when flow is commanded by the PCM restricted cannister,stuck or plugged cannister vent solenoid,etc....

On the base model it is located in the purge line between the carbon cannister and the purge solenoid. See pic below for base model diagram(click HERE for zoom)...


10_12_2011_1_33_42_pm.gif


Click HERE for zoom...

10_12_2011_1_34_31_pm.gif

If yopu need additional details, just Contact Us Here.

Hope thie helps.

Oct 10, 2011 | 1997 Ford Mustang Cobra

2 Answers

01 camry code po441...start with gascap?


This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.

EVAP emission canister purge is contolled by a valve which allows engine vacuum to pull stored fuel vapors from fuel tank into the engine to be burned, rather than be vented to atmosphere. A vacuum switch is used to detect when flow exists. If the PCM commands purge and sees that the switch is closed (indicating no detected purge flow) P0441 is set.

Causes: A code P0441 could mean one or more of the following has happened:
Bad vacuum switch
Broken or damaged EVAP line or canister
Open in PCM purge command circuit
Open or short in Voltage feed circuit to Purge Solenoid
Faulty purge solenoid
Restriction in EVAP solenoid, line or canister
Corrosion or resistance in purge connector
Bad PCM

Possible Solutions: with a P0441 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
Common Chrysler fix - Replace Leak Detection Pump / LDP
Repair damaged EVAP lines or canister
Repair open or short in voltage feed circuit to Purge Solenoid
Repair open in PCM purge command circuit
Replace purge Solenoid
Replace vacuum switch
Repair restriction in Evap line or canister or soleniod
Repair resistance in purge connector
Replace PCM

Hope this helps.

Aug 03, 2011 | 2001 Toyota Camry

2 Answers

Diagnostic code for 96 ford ranger-code number - p1443


Check the voltage on the purge flow (PF) sencor, with engine running...

Jun 19, 2011 | Ford Ranger Cars & Trucks

1 Answer

P1443 code How do I fix this code problem on my 97 Ford ranger?


P1443 is the Evaporative Emission Control System Control Valve. Any time you get this code always check your gas cap. If it is not installed all the way, or leaks, it can cause the evap emission code to come up. If the cap is okay...

The problem is probably caused by the Canister Purge Assembly. This assembly connects the intake manifold to the charcoal canister and the assembly is made up of hoses, a valve and a sensor. On the 1997 Ranger, it is located near the front of the engine compartment on the driver's side (the canister is right behind the driver's side headlight). Apparently, if there are any cracks in the hoses, or if the valve or the sensor wears out, this will cause the check engine light to come on, and return the P1443 code.

Part numbers for the canister purge solenoid/flow sensor assemblies:

F57Z-9C987-AB Canister Purge Solenoid/Flow Sensor
Assembly - 2.3L F57Z-9C987-CA Canister Purge Solenoid/Flow Sensor
Assembly - 3.0L F57Z-9C87-BA Canister Purge Solenoid/Flow Sensor
Assembly - 4.0L

Part cost = $65 to $100 depending on engine size - good luck :O)

Feb 17, 2011 | Ford Ranger Cars & Trucks

2 Answers

Ford escort wagon 1997 code p1443 displayed. what does this indicate & where is the cannister? thank you.


P1443 - EVAP Control System / Vacuum System Purge Control Solenoid Or Purge Control Valve Fault. A fuel tank pressure change greater than minus (-) 7 inches of water in 30 seconds occurred with a purge (fuel vapor) flow at less than 0.02 pounds per minute.

Possible Causes:
  • Blocked fuel vapor hose between the EVAP canister purge valve and the FTP sensor.
  • Blocked fuel vapor hose between the EVAP canister purge valve and the engine intake manifold.
  • Blocked vacuum hose between the EVAP canister purge valve solenoid and the engine intake manifold.
  • EVAP canister purge valve stuck closed (mechanically).

  • Possible Solution:
    Check for blockages between the fuel tank, the EVAP canister purge valve, and the engine intake manifold. Check for obstructions in the EVAP canister purge valve diaphragm and ports.

    The canister is on the passengers side near the firewall if I recall correctly.

    Jan 18, 2011 | Ford Escort Cars & Trucks

    1 Answer

    My name Tommy V, I have a 2001 Toyota Echo, the CK engine light was on, went to a car parts store used their code reader, code was PO441 Evaporative emission control -System incorrect, purge flow. I used...


    The EVAP cannister is part of the emissions system. Excess exhaust runs thru it-purge flow is when it is released. Check all the vacuum lines going to it. I don't you will find a parts listing for a purge flow valve or vent or solenoid. Your light will probably come on again shortly.

    Mar 15, 2010 | 2001 Toyota Echo

    1 Answer

    How to fix obd2 code 1443 on 96 ford ranger emisson test failed


    It is usually carbon pieces from the evap carbon canister clogging the purge solenoid and purge flow sensor. There should still be a one piece purge solenoid and purge sensor with hose assembly available. You will also need to replace the carbon storage canister.
    After replacement disconnect the negative battery cable, hold your foot on the brake pedal for 30 seconds, then reconnect the battery.

    Oct 25, 2009 | 1996 Ford Ranger SuperCab

    1 Answer

    Falt code p 1443


    Canister purge solenoid. Replace the solenoid and purge flow sensor if it has one.

    May 04, 2009 | 1996 Ford Mustang

    Not finding what you are looking for?
    2001 Ford Escort ZX2 Logo

    Related Topics:

    108 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    75822 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    fordexpert

    Level 3 Expert

    5501 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...