Question about Infiniti G35

Open Question

No acceleration power

My 04 g35x right signal automatically comes on and is not controllable. what causes this ?

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I changed everything on a 2007 Chevy uplander the camshaft position sensor And the purged sensor And the throttle body and still the check engine light and the reduce engine power came back on


Reduced Engine Power Mode When the ECM detects a condition with the TAC system, the ECM may enter a reduced engine power mode. Reduced engine power may cause one or more of the following conditions:
?€¢
Acceleration limiting--The ECM will continue to use the accelerator pedal for throttle control, however, the vehicle acceleration is limited.


?€¢
Limited throttle mode--The ECM will continue to use the accelerator pedal for throttle control, however, the maximum throttle opening is limited.


?€¢
Throttle default mode--The ECM will turn OFF the throttle actuator motor and the throttle will return to the spring loaded default position.


?€¢
Forced idle mode--The ECM will perform the following actions:


-
Limit engine speed to idle by positioning the throttle position, or by controlling the fuel and spark if the throttle is turned OFF


-
Ignore the accelerator pedal input


?€¢
Engine shutdown mode--The ECM will disable fuel and de-energize the throttle actuator.
Did you have it checked for DTC's - diagnostic trouble code's related to the reduced engine power ?
All so has APP sensor gas pedal !
Accelerator Pedal Position (APP) Sensor
The accelerator pedal contains 2 individual accelerator pedal position (APP) sensors within the assembly. The APP sensors 1 and 2 are potentiometer type sensors each with 3 circuits:
?€¢
A 5-volt reference circuit


?€¢
A low reference circuit


?€¢
A signal circuit

The APP sensors are used to determine the pedal angle. The engine control module (ECM) provides each APP sensor a 5-volt reference circuit and a low reference circuit. The APP sensors provide the ECM with signal voltage proportional to the pedal movement. The APP sensor 1 signal voltage at rest position is less than 1 volt and increases to more than 4 volts as the pedal is actuated. The APP sensor 2 signal voltage at rest position is less than 0.6 volt and increases to more than 2 volts as the pedal is actuated.
Your best bet is take your vehicle to the dealer !
al

May 03, 2016 | Cars & Trucks

1 Answer

What causes the "Reduced Engine Power", "Service Stability Control" and "Traction Control" warning lights to come on?


the "Reduced Engine Power", problem causes the PCM to disable "Service Stability Control" and "Traction Control" turning on the warning lights to come on for those systems . The reduced engine power is because of a problem with the electronic throttle control system or as GM calls it TAC system . Reduced Engine Power Mode
When the PCM detects a condition with the TAC system, the PCM may enter a reduced engine power mode. Reduced engine power may cause one or more of the following conditions:
• Acceleration limiting--The PCM will continue to use the accelerator pedal for throttle control, however, the vehicle acceleration is limited.
• Limited throttle mode--The PCM will continue to use the accelerator pedal for throttle control, however, the maximum throttle opening is limited.
• Throttle default mode--The PCM will turn OFF the throttle actuator motor and the throttle will return to the spring loaded default position.
• Forced idle mode--The PCM will perform the following actions:
- Limit engine speed to idle by positioning the TP, or by controlling the fuel and spark if the throttle is turned OFF.
- Ignore the accelerator pedal input.
• Engine shutdown mode--The PCM will disable fuel and de-energize the throttle actuator.
© 2017 General Motors Corporation. All rights reserved.



Drive by Wire training Your best bet , take it to a GM dealer

Mar 04, 2017 | 2005 Pontiac Grand Prix GT

1 Answer

Ford focus cruise control


Once you have turned your cruise control on accelerate to desired speed press SET button on right hand side of steering wheel before lifting foot from accelerator, then remove foot from accelerator. pushing RESUME button will deactivate cruise control without turning it off. Then when clear of traffic push resume again to activate cruise control. It will automatically resume to previous set speed.

Apr 30, 2013 | 2006 Ford Focus

1 Answer

A yellow warning light like a wheel spinning. What is it?


This is a traction control light. It seems like your TCS is bad, or has a sensor issue causing the vehicle to retard the acceleration. The car thinks that it is losing traction, so It is automatically trying to compensate

Feb 28, 2013 | Cars & Trucks

1 Answer

04 toyota tacoma squeals on left side of engine compartment during acceleration only, what is causing this noise???.


Could be your belt is stretched and needs to be replaced,can't tighten cause it's done by tensioner.Here's a link to the belt replacement guide.To check out noise,open hood,stand at engine,have someone start,listen for noise,have person rev up engine and you find where noise is coming from.Also check tensioner.

Feb 11, 2013 | 2004 Toyota Tacoma

1 Answer

Have 2006 gmc canyon having trouble with it staying on.3.5 engine starts up,stays on a few seconds then shuts off shows reduced power on panel.won't crank over .have to wait a few minutes then it


REDUCED POWER
Refer to:
• Powertrain Control Module Description for the 2.8L engine
• Powertrain Control Module Description for the 3.5L engine

Throttle Actuator Control (TAC) System
Throttle Actuator Control (TAC) Overview
The throttle actuator control (TAC) system uses vehicle electronics and components to calculate and control the position of the throttle blade. This eliminates the need for a mechanical cable attachment from the accelerator pedal to the throttle body. This system also performs the cruise control functions as well.
The TAC system components include, but are not limited to the following:
• The accelerator pedal position (APP) sensors
• The throttle body
• The powertrain control module (PCM)
Each of these components interface together to ensure accurate calculations and control of the throttle position.

Accelerator Pedal Position (APP) Sensor
The accelerator pedal position (APP) sensor is mounted on the accelerator pedal assembly. The APP is 2 individual APP sensors within one housing. There are 2 separate signal, low reference, and 5-volt reference circuits. APP sensor 1 voltage increases as the accelerator pedal is depressed. APP sensor 2 voltage decreases as the accelerator pedal is depressed.
Throttle Body Assembly
The throttle body for the throttle actuator control (TAC) system is similar to a conventional throttle body with several exceptions. One exception being the use of a motor to control the throttle position instead of a mechanical cable. Another exception is the throttle position (TP) sensor. The TP sensor is mounted in the throttle body assembly. The TP sensor is 2 individual TP sensors within the throttle body assembly. Two separate signals, low reference, and 5-volt reference circuits are used to connect the TP sensors and the powertrain control module (PCM). TP sensor 2 signal voltage increases as the throttle opens. TP sensor 1 signal voltage decreases as the throttle opens.

Reduced Engine Power Mode
When the PCM detects a problem with the throttle actuator control (TAC) system the PCM enters one of the following Reduced Engine Power Modes:
• Acceleration Limiting--The control module will continue to use the accelerator pedal for throttle control, however the vehicle acceleration is limited.
• Limited Throttle Mode--The control module will continue to use the accelerator pedal for throttle control, however the maximum throttle opening is limited.
• Throttle Default Mode--The control module will turn OFF the throttle actuator.
• Forced Idle Mode--The control module will perform the following actions:
- Limit engine speed to idle by positioning throttle position, or by controlling fuel and spark if throttle is turned OFF.
- Ignore accelerator pedal input.
• Engine Shutdown Mode--The control module will disable fuel and de-energize the throttle actuator.

Have you had it checked for DTC'S - diagnostic trouble codes ?

DTC P2176
The commanded throttle position (TP) is compared to the actual TP. Both values should be within a calibrated range of each other. The powertrain control module (PCM) continuously monitors the commanded and actual TPs. If the values are greater than the calibrated range, DTC P2176 sets.
--------------------------------------------------------------------------------
DTC P2138
The accelerator pedal position (APP) sensors 1 and 2 are located within the accelerator pedal assembly. Each sensor has the following circuits:
• A 5-volt reference circuit
• A low reference circuit
• A signal circuit
This provides the powertrain control module (PCM) with a signal voltage proportional to accelerator pedal movement. The APP sensor 1 signal voltage at rest position is near the low reference and increases as the pedal is actuated. The APP sensor 2 signal voltage at rest position is near the 5-volt reference and decreases as the pedal is actuated.
DTC P2135
The throttle actuator control (TAC) assembly has 2 throttle position (TP) sensors mounted within the assembly. The powertrain control module (PCM) provides individual signal, ground, and 5-volt reference circuits to each sensor. Both sensors operate within a voltage range between 0.35-4.65 volts. When the throttle is opened from 0-100 percent, one sensor signal voltage increases while the other decreases. The signal circuit for TP sensor 1 is referenced to ground, and the signal circuit for TP sensor 2 is pulled up to 5 volts within the PCM.
DTC P2128
DTC P2127
DTC P2125
DTC P2123

Drive by Wire Function and diagnostics by Wells

May 25, 2017 | 2006 GMC Canyon

3 Answers

Error code p2138


Here is the definition. You may need to have someone check the accelerator pedal position sensor and the circuit.

P2138 NISSAN Description The Accelerator Pedal Position (APP) sensor is installed on the upper end of the accelerator pedal assembly. The sensor detects the accelerator position and sends a signal to the Engine Control Module (ECM).
Accelerator pedal position sensor has two sensors. These sensors are a kind of potentiometers which transform the accelerator pedal position into output voltage, and emit the voltage signal to the ECM.
In addition, these sensors detect the opening and closing speed of the accelerator pedal and feed the voltage signals to the ECM. The ECM judges the current opening angle of the accelerator pedal from these signals and controls the throttle control motor based on these signals.
Idle position of the accelerator pedal is determined by the ECM receiving the signal from the accelerator pedal position sensor. The ECM uses this signal for the engine operation
such as fuel cut.
Read more: http://engine-codes.com/p2138_nissan.html#ixzz26J3D2x8s

Sep 12, 2012 | 2010 Nissan Versa 1.8

2 Answers

The reduce engine power message keeps coming on, giving limited power when driving does anyone know what the proble could be with my 2007 hummer H2 SUT.


The Powertrain Control Module (PCM) is shutting down your throttle body control for some reason and limiting how much throttle you can apply. The only way to find out why it is doing this is to scan the PCM for Diagnostic Test Codes (DTCs) and diagnose any existing codes accordingly. It is very likely to be caused by a fault in your throttle position sensor or accelerator pedal position sensor circuits.

There is a Technical Service Bulletin (TSB) for your vehicle which covers a known problem with reduced engine power and sets DTC P2138. The known problem is that the Accelerator Pedal Position (APP) sensor circuits are being infiltrated by water intrusion into a connector and causing erratic voltage readings at the PCM. It is TSB reference # 07-06-04-019D

Jul 18, 2011 | 2007 Hummer H2 SUT

1 Answer

What causes a toyota highlander VCS warning


When your VSC (Vehicle Stability Control) light comes on, it means your car has been forced to take evasive action to avoid a dangerous situation. For example, if you're driving on an icy or wet, slippery road, and take a turn too sharp or accelerate too quickly, the vehicle will automatically reduce acceleration or apply pressure to the brakes to prevent the car from losing control. In this situation the VSC indicator light will light up to alert you that the action was taken, and remind you to slow down - or to be extra careful. Be safe!

Jan 18, 2010 | 2005 Toyota Highlander

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Infiniti Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14333 Answers

Are you an Infiniti Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...