Question about 2000 Mercury Villager

1 Answer

Timming belt no spark motor just quit

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mercury Master
  • 4,369 Answers

Remove distributor cap, crack engine. if rotor does not turn, the timing belt is boken. 105,000 maintenance interval.
If rotor does turn, it is likely the distributor. Repalce with Rich Porter NS 60 for $115 on eBay or Amazon. 1999 noted for this issue.

Gerry

Posted on Feb 11, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 trail blazer will not start,fuel pressure


you might want to check to see if you got a timming chain or belt in that car.
but check that area first .
could be a broken timming belt.
you need to remove the dust cover in that area .
check for no belt present on the timming gears.
good luck,Gary

Oct 24, 2013 | 1996 GMC Sonoma

2 Answers

I have spark from my coil but I have no spark from my distributer cap on my dodge dakota 1992 v8 5.2 liter


at the distbutor itself there is a part that is called the picup coil most of the times that is what goes bad.

Jan 24, 2013 | Cars & Trucks

1 Answer

How to replace a broken timing belt for a 1998 daewoo lanos?? Would there be any head damage?


yes it is quite possible that valves are bent if the cam belt broke or teeth stripped off of old belt, which unfortuneately means removing the cylinder head and getting it repaired (valves replaced and possibly guides) see some of my other posts for cam belt timming marks locations etc...
depending what motor is in your vehicle twin cam or single?

stevenhurc_14.jpg and if its twin cam you usually need cam locking tool for cam gears.

Apr 20, 2011 | Daewoo Lanos Cars & Trucks

1 Answer

I have just replace my water pump and timming belt on my car. Now the car put all back together. Now the car will not start could the timming be off on the car now?


Any time you take off the timing belt and replace it could be off. It depends on how much care you took to make sure the timing didn't move in the process. Recheck the timing marks to make sure they are still on. If so then check for unplugged connectors. If you left the cam or crank sensor unplugged the computer won't get the signal telling it to spark. If you have a spark tester and a friend hook the tester up to cyl. 1 and have your friend crank the motor while you look to see if it sparks. Also if you removed the battery cables during the process then the car's factory security system may be stopping it from starting. The factory immobilizers can cause all kinds of problems after the battery gets low or is disconnected.

May 01, 2010 | 2002 Dodge Intrepid

1 Answer

I had the timming belt done on my 94 honnda accord


The spark isnt controlled by the timing belt. The only thing that belt controls is the timing of the valves opening and closing. The spark is controlled by a crankshaft position sensor, or something like it. The only way i know how to check the timing of the valves is to take the valve cover off and observe the opening and closing of the valves as the engine is rotated by hand.

Jan 31, 2009 | 1994 Honda Accord

1 Answer

Just Quit Running?


find /replace crank angle sensor ... for the switching device....... do you have a way to pull codes ?

Nov 21, 2008 | 1997 Suzuki Esteem

1 Answer

Won't start


check for spark and please email me at meanness628@aim.com with any other info or questions

Sep 18, 2008 | 1999 Dodge Intrepid

Not finding what you are looking for?
2000 Mercury Villager Logo

Related Topics:

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

fordexpert

Level 3 Expert

5481 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...