Question about 2004 Suzuki Aerio

1 Answer

Replace o2 senors - 2004 Suzuki Aerio

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Suzuki Master
  • 20,706 Answers

Is the word how to?> missing ?/
or is this show and tell?
post a real question.please... who,what ,when , how , why...... 100s.
and engine option, we cant guess what engines.
here is the list.

1.3 L I4; 1.5 L I4; 1.6 L I4; 1.8 L I4; 2.0 L I4; 2.3 L I4; 1.4 L Diesel I4

simple generic answer. how to???
unplug sensor
unscrew it
put back new. reverse of above.
some cars have 4 sensors. only the front need changing
if economy is the goal.
front means closest to engine .

Posted on Feb 10, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the O2 sensor in a 2005 PT Cruiser?


your upstream o2 sensor is located behind motor and manifold and need an o2 senor socket and racket plus extension to remove and then your downstream 02 sensor is on the side of Cat convertor (drive side)and same process to remove and replace

Jul 30, 2013 | 2005 Chrysler PT Cruiser

1 Answer

2004 5.4 crank senor location


its normally behind the harmonic balancer under the front of the engine..

Feb 10, 2013 | 2004 Ford F150

1 Answer

My car will not start, I replaced the starter, replaced the battery 2 months ago, I replaced the mass air flow senor,crank shaft senor and modulator? When you try to start it, it shudders and will not...


That still could be a number of things. Fuel pump, O2 sensor, Ignition coil, etc. A good way to find out if its a fuel or electrical problem is to get a can of starter fluid. Open the air intake and spray a little inside and see if it starts. If it does not, then you have a spark or sensor problem. If it does start, then you have a fuel problem.

Nov 21, 2010 | 2000 Buick LeSabre

1 Answer

REPLACE BANK 2 o2 SENSORS 1996 CONTINENTAL


bank 1 and bank 2 refer to the positioning of the sensor on the car, bank 2 just means the second one, so if you start out at your exhaust manifold and inspect the piping going back, the second O2 senor you find will be the one you need to change, it will likely be around or near the catalitic convertor.

Mar 21, 2010 | 1996 Lincoln Continental

1 Answer

Have a 2002 Honda Civic HX that when idling the heat stops working and the engine begins to overheat, when revving the engine heat kicks in and temp goes down. Intermittent problem, will go hundreds of...


I would check o2 sensors but to tell you the truth my dad bought a new thermostat that was suppose to open at 160 degrees his temp. got to 220 degrees before but check o2 senors and thermostat

Feb 01, 2010 | 2002 Honda Civic

2 Answers

S10 Blazer 1999 the computer reads problem is Bank 1 sensor 3 what sensor and where is bank1 pinkie


Bank 1 is the drivers side. But the sensor you want is the one farthest back, right before the muffler.

May 04, 2009 | 2000 Chevrolet Blazer

1 Answer

How to install o2 senor on 1996 jetta


get the o2 sensor off just use an open end wrench turn counterclockwise disconnect the connector and put the new one on ?please rate my respose thank you very much

Feb 01, 2009 | 1996 Volkswagen Jetta

1 Answer

Eng check lite


weird. usually an intermitent problem like that for are o2 sensor means that your catalytic converter is starting to cause problems but that should only set a code for sensor 2 not both sensors. sorry i cant be more help

Oct 21, 2008 | 2001 Mitsubishi Montero

2 Answers

Obd codes for a 1994 cadillac seville sls


It means the heater circuit for the O2 sensor has failed. An O2 sensor has to be up around 900 degrees to function properly, and if its heater fails, it won't get up to temperature (thus the "not ready" diagnosis). Replacing the O2 sensor will fix your problem.

Sep 30, 2008 | 1994 Cadillac Seville

Not finding what you are looking for?
2004 Suzuki Aerio Logo

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...