Question about 1999 Ford F250 Regular Cab

1 Answer

Where can the pick up coil be located - 1999 Ford F250 Regular Cab

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.


    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 109 Answers


Posted on Dec 13, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Pick-up coil

2002 express doesn't have a pickup coil - it has a camshaft sensor in the distributor, the crankshaft sensor is located in the lower corner of the front cover. Crank sensor is straight forward to replace, the Cam sensor you remove the dist cap and rotor - spin motor over until notch in the shaft lines up with cam sensor, remove bolts and slide up.

Feb 21, 2014 | 2002 Chevrolet Express

1 Answer

I need to know the location of pick up coil 97 jeep wrangler

look at distributor cap the wire tha't is in the middle follow it to other end that is gonna be your pick up coil

Mar 28, 2011 | Jeep Wrangler Cars & Trucks

1 Answer

Ford focus 2002, 2 litres, what is the function of the pick up coil

The pick up coil is located at the base of the distributor and plugs into the ignition module. The pick up coil's purpose is to sense or "pick up" the pulses of the distributor and tell the ignition module when to fire the spark plugs. The most critical part of the replacement of the pick up coil is to make certain you properly mark the orientation of the distributor to the engine block and the rotor to the distributor base. When you successfully make these markings, you will not need to check your timing when this job is finished. Keeping this in mind, here we go: You will need to purchase a replacement pickup coil and a rubber o-ring gasket that will replace the o-ring located where the distributor shaft enters the engine before you start this project.

Dec 05, 2010 | 2002 Ford SVT Focus

1 Answer

Car would be driving fine then just stop then start again and run, now it was running and stopped and wont start , replaced plugs,cap,rotter,coil but its not getting spark.

Sounds like an ignition module and/or a pickup coil. If there is injector pulse the pickup coil is working.

The ignition module is located on the side of the distibutor. The make a wrench that has both the socket and the torx bit all in one just to install one of these. The wrench should be available from the autoparts store you get the ignition module from. It will make install a lot easier.

Sometimes you have to rotate the distributor a little to get at the two bolts that hold the module to the distributor. Make sure you mark the location of the distributor before you rotate it so that you can but it back in exactly the same place.

Once the two bolts are removed gently push down on the module to disconnect it from the pick-up coil. Sometimes its nice to remove the cap to help line up the new one with the pick-up coil connector and make sure the pick-up coil connector is in tacked. It is not uncommon for them to crumble when replacing the module.

Nov 30, 2010 | 1993 Ford Tempo

1 Answer

Where is the pickup coil located on 1997 dodge ram

he pick-up coil/stator assembly is located under the distributor cap, and once the distributor cap is removed from the distributor, just remove the ignition rotor, and then simply un-plug the wire connector to the the pick-up coil/stator and then lift it straight up and away from the distributor, and when re-installing the pick-up coil/stator be sure to align the square tab and the rounded tab on the pick-up coil/stator to match with the distributor housing and with the distributor cap and install the ignition rotor and the distributor cap, and then re-connect the wire connector to the pick-up coil/stator.


Sep 24, 2010 | 1997 Dodge Ram

1 Answer

94 pontiac with 5.7L, wont start. Fuel and fire are there and a new computer, still won't start

These distributors are bad to have problems,where they are located,the pick up coil is the most likely problem,the pick up coil pulses the injectors,I assume this is your problem,spray starting fluid in the intake,and see if it hits,it will not run long,do not move accelerator ,just spray in a vacuum port where the fluid can **** threw to the cylinders,if it hits,then the pick up coil in the distributor is the problem.

Jun 07, 2010 | 1994 Pontiac Firebird

1 Answer

Need location of pick up coil on engine please

PICK UP COIL FOR WHEEL CYLINDERS? ENGINE coil? ALLECAROMETER PICKPUP coil or master brake cylinder pickup coil for anti skid brakes? or RPM pickup coil for tach and speedo?

Apr 11, 2010 | 1999 Oldsmobile Bravada

1 Answer

1997 pick-up coil

Your pickup is on the bottom of your distributer under the cap. It looks kind of like a star. You will have to remove you cap, rotor and module to replace it.

Jul 09, 2008 | 1997 GMC Jimmy

Not finding what you are looking for?
1999 Ford F250 Regular Cab Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

79851 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides