Question about 2004 Mitsubishi Endeavor

1 Answer

Driver's window will not operate

Window will not go up or down

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 128 Answers

FIRST CHECK FUSES,IF ALL GOOD THEN IT MAY BE THE MOTOR GONE BAD ON THE WINDOW MOTOR

Posted on Mar 02, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The battery got disconected now windows dont work tried re program checked fuses nothing now what


You need to do a window reset. Its in your owners manual

This is a quote from the workshop manual

Note
? A driver side window will not fully close automatically under following the conditions:
? The battery has been disconnected during vehicle maintenance or for other reasons.
? The power window main switch connector, or driver-side power window motor connector has been
disconnected.
? Carry out the following procedure to resume operation:
1. Turn the ignition switch to the ON position.
2. Press the driver side power window main switch and fully open the driver side window.
3. Pull up the driver side power window main switch to manual-up position to fully close the driver side window,
and keep holding the switch up at the position for about 2 seconds to complete initial setting.

TWO-STEP DOWN FUNCTION OPERATIVE/NON-OPERATIVE SWITCHING PROCEDURE

Note
? By following the procedure below, the two-step down function is switched to non-operative when it is
operative, and to operative when it is non-operative.

Turn the Ignition on
Within 5 sec
perform the auto open two times
perform the auto close two times

turn the ignition off and within 40 seconds and repeat the above sequence.

Repeat for all the windows.

Aug 14, 2016 | 2007 Mazda 6 2.3

1 Answer

I need the wiring schematics for driver door panel and all switches in a 2003 Chevy Tahoe. My window won't go down on that side and I'm sure I have a short somewhere because my switch works with all other...


You don't know what your getting into , The door switches have electronic control modules incorporated ,DDM- Driver door module an PDM passenger door module .
The power window system consists of the following components:
?€¢
Driver Door Module (DDM)


?€¢
Passenger Door Module (PDM)


?€¢
Body Control Module (BCM)


?€¢
RR power window switch


?€¢
Window up and window down relays in each of the rear passenger window switches


?€¢
Window lockout switch


?€¢
Reversible power window motors in each of the doors (circuit breaker protected)


?€¢
LT DOOR CB 25A (System power for left windows)


?€¢
RT DOOR CB 25A (System power for right windows)


The DDM contains four power window switches which are integral components. Closing any of the normally open, rocker type switches provides the DDM with a request for power window operation. The switches for the two front windows have three positions UP, Down and Express Down, while the switches for the rear windows have only two positions, UP and Down. Each of these switches and their positions is a direct input into the DDM. Upon receiving a request for power window operation, the DDM, transmits a Class 2 message indicating the switch and it's changed position.
The PDM contains a single power window switch that is an integral component. Closing of this normally open, rocker switch provides the PDM with a request for the front passenger power window operation. The switch for the front passenger window has two positions Up and Down. Each of these switch positions is a direct input to the PDM.
The two rear passenger doors have there own switches. Each of the switches contain a power window up and down relay. A switch activation alone can control the up and down functions of the rear windows. However the BCM, upon receiving a Class 2 message from the DDM, can control the set of relays which will activate the rear window motors.
You need a scan tool to diagnose these systems
Power Window Inoperative - Driver Door

1

Did you perform the Door Systems Diagnostic System Check?
Go to Step 2
Go to Diagnostic System Check - Door Systems

2

Operate the driver power window in the UP and DOWN directions.
Does the driver power window operate properly?
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
Go to Step 3

3

  1. Install a scan tool.
  2. Monitor the driver window status data parameter in the driver door inputs list.
Does the driver window status data parameter display an active state?
Go to Step 11
Go to Step 4

4

  1. Monitor the driver window status data parameter in the driver door module inputs list.
  2. Activate the driver power window switch in the up and down positions.
Does the driver window status data parameter change accordingly?
Go to Step 5
The data link connector (DLC) allows a scan tool to communicate with the class 2 serial data line. The serial data line is the means by which the microprocessor-controlled modules in the vehicle communicate with each other. Once the scan tool is connected to the class 2 serial data line through the DLC, the scan tool can be used to monitor each module for diagnostic purposes and to check for diagnostic trouble codes (DTCs). Class 2 serial data is transmitted on a single wire at an average of 10.4 kbps.

You

Mar 24, 2015 | Cars & Trucks

1 Answer

I replaced the driver's side window motor because


I don't know everything there is to know about window motors, but I have seen this before, both mine went out at the same time, not together but a couple weeks apart, like they were dated. Anyway, I replaced both motors, then both operators. Now they both work fine. I would hang on to the old motor, you never know, it might be good, You might have a bad switch on the door, I had to take my switches apart on my other truck and clean the contacts, got both motors working again, Hope this helps.

Mar 20, 2010 | 2003 Hyundai Tiburon

1 Answer

All windows but drivers won't go up or down 2001 GMC yukon


If they sound like they are trying to do something it's not the lock out switch . But to be sure pulling out the switch an testing for B+ voltage to and from the switch . Plus pull the other door switches to see if they have B+ voltage and good grounds would be the thing to do.. If you don't know how to check automotive electrical circuits your best bet , take it to a qualified repair shop .
Passenger Power Window Operation
The passenger power window switches incorporate window up and down relays. The relay coil feed and supply sides are powered through the RAP fuse supply voltage circuit. The normally closed contacts of each relay is connected to ground. The load side of each of the relays are connected to either side of the power window motor through the power window up and down circuits. The up and down relay control circuits are connected to the normally closed contacts of the passenger window switch. These contacts are wired in series with the power window master switch, through the power window master switch up and down signal circuits and then to ground when the power window master is placed in the up or down position. This allows for the up and down operation of the passenger power window from the power window master switch. The center pole of the passenger power window switch is also connected to ground and will energize the relay when placed in the up or down position.

Driver Power Window Operation
The driver power window is unique from the passenger power windows in that it does not use window up and down relays. The driver power window is operated directly from the power window switch.
The normally closed contacts of the switch are connected to ground and the center pole is connected to the RAP fuse supply voltage circuit. By placing the left power window switch in the down position, voltage is applied to the power window motor left front down circuit and to the power window motor. The other side of the power window motor is connected to ground through the normally closed contacts of the left power window switch through the power window motor left front up circuit and drives the window down.
By placing the left power window switch in the up position the polarity of the motor is reversed and the motor drives the window up.

Has circuit breaker for B+ power
• PWR WDO CB 25A (fuse block) (System power for left and right windows 2-door vehicles. System power for LF and LR windows 4-door vehicles)
• PWR WDO CB 25A (IP wiring harness junction block) (System power for RF and RR windows 4-door vehicles)

Could be passenger door switch .

Aug 21, 2017 | 2001 GMC Yukon XL

1 Answer

The windows don't work right


If the passenger front window switch operates up & down correctly the left drivers side switch is bad and needs a replacement switch

May 29, 2009 | 2001 Chrysler Concorde

1 Answer

2003 F250 Power Windows won't work


check fuses 35 & 41 (10 amp, red).
it also shows an accesory delay relay in the fuse panel.
And fuse 601? 30 amp.

make sure you don't have lock-out on driver switch panel activated.

Power Window System
Features and Operation
NOTE: The accessory delay feature will allow power window operation up to 10 minutes after the ignition is off or until a door is opened.
If equipped with power windows, the window control switch (14529):
  • will operate the power windows only when the ignition switch is in the RUN or ACC position.
  • is located on each front door trim panel, and Crew Cab and Excursion rear door trim panel.
  • may be used to raise or lower the driver side, passenger side and rear windows from the LF control on the driver side, or the passenger window from the passenger switch.
  • includes a one-touch down (OTD) feature for the driver door window.
  • can partially lower the driver side window when the LF window control switch is depressed half way (first detent).
  • will completely lower the driver side window when the LF window control switch is fully depressed and then released (second detent).
Power Window System — Modes of Operation
There are two modes of operation for the power window system.
Manual Mode
When the LH window control switch is pressed to the first down position, the window will move down until one of the following conditions are met:
  • The LH window control switch is no longer in the first down position.
  • The LH window control switch is pushed to the OTD position, causing the windows to enter auto mode.
Auto Mode
Auto mode provides the OTD feature. The OTD feature is activated when the LH window control switch, for the LH window, is pressed to the second down position.
Auto mode will be terminated when any of the following conditions are met:
  • The LH window control switch is pushed to the UP position.
  • The LH window control switch is released (OFF position) and then moved to the DOWN position (first detent) or OTD position (second detent).
  • Note: Delayed accessory feature must be active.
The OTD feature is controlled by the window control switch.

---------------------------------------------------------
Condition Possible Sources Action
  • All power windows are inoperative
  • Fuse(s).
  • Circuitry.
  • LF window control switch.
  • Accessory delay relay.

May 23, 2009 | 2003 Ford F250 Super Duty Crew Cab

1 Answer

What color are power wirers that control the left power window contols on my 2000 ford taraus.


Principles of Operation
Power Window Control
The one-touch down (OTD) power window function allows the driver door window glass to completely lower with one button press. The driver window control switch is hardwired to the generic electronic module (GEM) and door window regulator and motor. When the GEM senses a one-touch down request from the driver window control switch, the GEM supplies a ground to the OTD Relay coil. The OTD relay then provides power to the driver window regulator motor, lowering the window. The OTD feature will function when the ignition switch is in the RUN or ACC position. The OTD feature also operates while the ignition is OFF and the accessory delay time-out period has not expired
--------------------------------------------------
27b502f.gif

May 07, 2009 | 2000 Ford Taurus

1 Answer

Is the fuse panel under the hood the only place fuses are located? and i dont have manual to see which fuse is for my driver side window... its not working


you have fuses inside the car on the dash about where left knee is.
This is for 2003, don't have 2004. should be similar.

fuse 2.43, 20 amps, yellow, central junction box in car


Principles of Operation
Power Window Control
NOTE: Battery power and ground must be removed before disconnecting the GEM connectors to avoid setting false DTCs.
The driver power window one-touch down operation is controlled by the generic electronic module (GEM). This feature functions only when the ignition switch is in the RUN or ACCY positions. The GEM determines ignition switch position by monitoring the key-in ignition, RUN/ACCY and RUN/START circuits. The one-touch down operation is requested of the GEM by momentarily pressing the driver window regulator control switch DOWN for 62 ms to 320 ms. The GEM uses the initial voltage input from the down switch to begin the one-touch down operation. If the voltage input was less than 320 ms, the GEM will maintain the voltage supply to the motor down circuit. The GEM will maintain the operation until:
  • seven seconds expires.
  • motor stall is detected by monitoring the current draw.
  • a voltage input is received by the GEM on either the up or down switch circuits.
The ground for one-touch down operation does not pass through the GEM. The ground is supplied through the driver window regulator control switch as with normal operation. If the GEM continues to see voltage on the down circuit for more than 320 ms after initial activation the GEM will not effect operation. The down circuit through the GEM is a direct connection to the motor in its normal state. This allows the driver window regulator control switch to control the motor for normal operation.
The passenger window motors are hardwired directly to the window regulator control switches.

Apr 27, 2009 | 2004 Ford Mustang

Not finding what you are looking for?
2004 Mitsubishi Endeavor Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...