Question about 2008 Cadillac Srx

Open Question

Replace front turn signal light on 2008 srx - 2008 Cadillac Srx

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: Replacing front turn signal bulb on 2006 Cadillac SRX

wow i feel sorry for you because Cadillac designed this bulb to be a don't get to bulb but OK here's what you do take the bottom cover off or skid plastic panel under neath the front end theirs little plastic clips holding it on just get come dikes and don't cut them but just use it to help pull them out. after you get that off use a flash light and locate your light housing you should see two screws holding the house in i think those screws are 8mm i cant remember remove those two screws and be careful the metal from the bumper cuts you pull the light housing out and remove all the screws around the housing and open the housing up replace the bulb and make sure your contact to the bulbs clean and then reassemble the way you took apart. if you cant get it well then best bet is take it somewhere i know Cadillac charges an arm and a leg so you can go somewhere else.

Posted on Jan 25, 2009

jpstuhr
  • 49 Answers

SOURCE: how to replace front turn light bulb on Caddy SRX 2004?

  1. Open the hood.
  2. Remove the push-pin retainers that secure the top of the upper fascia and grille assembly to the upper tie bar to allow the upper fascia and grille assembly to flex forward.
  3. Remove the bolt and the push-pin retainer that secures the top of the headlamp assembly to the upper tie bar.
    1. Gently pull the upper fascia and grille assembly forward only far enough to remove the bolt located at the bottom inboard side of the headlamp assembly.
    2. Pull the headlamp assembly straight out to disengage the snap-in retainer at the lower outboard back surface of the assembly. Turn the assembly so that the front inboard corner clears the front fascia.
    3. Pull the headlamp assembly out and away from the vehicle
    4. Disconnect the headlamp electrical connector.
    5. Remove the headlamp assembly from the vehicle.
    6. Remove the headlamp bulb cover from the headlamp assembly.
    7. Remove the headlamp bulb socket from the headlamp assembly.
    8. Remove the headlamp bulb.
    9. Remove the side marker bulb socket from the outer side of the headlamp assembly.
    10. Remove the side marker bulb.

Posted on Feb 12, 2009

  • 156 Answers

SOURCE: Front turn indicators don't work, on 04 Cadillac SRX

you may want to check the fuse for the signals and asfor the locked windows, it sounds like your window lock has either seized or the button is off track. In any case, replacement would be the best option.

Posted on Feb 23, 2009

  • 1 Answer

SOURCE: Need to replace front turn signal bulb on a 2004

need to remove front wheel and panel from the inside.

almost the entire wheel cover need to come off

Posted on Aug 06, 2010

alicantecoli
  • 22095 Answers

SOURCE: how do you change the

take the head light unit out complete

Posted on Sep 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 cadillac srx fixing or replacing light bulbs rear license plate


You might be able to access it if you stick your hand up inside the rear of the bumper.

Nov 26, 2015 | 2008 Cadillac Srx

1 Answer

Cadillac srx 2007


sounds like a fuse is blown. check your fuses

Aug 02, 2013 | Cars & Trucks

1 Answer

How to change front turn signal bulb on 2008 SRX Cadillac


Nope don't need to drop the whole light assembly. I just took the wheel and inner cover off, then the 6 torx screws that hold the light hosing together , replaced the turn signal bulb and good to go!!

Mar 04, 2013 | 2004 Cadillac SRX

1 Answer

How do i replace the fuse for the front turn signal on 2006 cadillac srx


The socket is defective?? Probe the socket with a volt meter to see if voltage is turning on and off to trigger the bulb to flash.

Jul 09, 2012 | 2006 Cadillac SRX

1 Answer

Change turn signal bulb 2008 srx


Front turn signal bulb replacement 2008 SRX . Jack up car & block . Remove front wheel & front half of the wheel house assemble. There are about 7 plastic pull rivets that have to be removed . Pull out the wheel house . Remove turn signal & driving light cover held on by 6 # T10 torx screws . Twist out socket & replace bulb # 3757NAK . Should take about 45 min.

Mar 26, 2012 | 2006 Cadillac SRX

3 Answers

I need to change the left front turn signal bulb on a 2006 Cadillac SRX? Looks difficult. Paul LeMaster


hi Paul

Should be able to open the hood remove plastic headlight cover & pull pins (2) on light assembly whole light assembly will pull out then replace turn signal.

Good luck.

Dec 02, 2009 | 2006 Cadillac SRX

1 Answer

How do I change the left running light on a 2005 Cadi SRX?


Hi there,
Open the hood and look behind the head lamps, there should be a wire or two going into a unit that is connected to the head lamp. You should be able to reach in there and you will probable have to turn the unit left or right and pull it out. Your light buld will be connected to it. Take the bulb to a local parts store and they will match it. The same is for all the lights. Hope this help you out. Let me know. Have a great night.~MWD

Mar 26, 2009 | 2008 Cadillac Srx

1 Answer

Front turn indicators don't work, on 04 Cadillac SRX


you may want to check the fuse for the signals and asfor the locked windows, it sounds like your window lock has either seized or the button is off track. In any case, replacement would be the best option.

Feb 23, 2009 | 2004 Cadillac SRX

2 Answers

Replacing front turn signal bulb on 2006 Cadillac SRX


You must take the front wheel off, then remove the inner front fender panels (2), they are fastened with plastic pushbuttons. this exposses the light housings for the turn and fog lambs. This takes about an hour, but saves you alot of money.

Nov 12, 2008 | 2006 Cadillac SRX

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...