Question about 1995 Toyota Tercel
Need to know how to set the timing
What engines, there are 5 engines, in 1995
nobody can help you unless. you tell engine class and if clever, country.
Posted on Feb 09, 2014
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Both are located under the timing cover.you will have to remove the timing sproket to get to the CrankshaftPS. be careful to notice how you removed it. the sproket have to be reinstalled exactly the same way you removed it.
Posted on Dec 19, 2008
malibluert: YOUR IN LUCK! This series engine is simple and the references aren't hard to find. READY???????
IF you are just trying to reset the belt at the top and have not remover the crank pulley, bring the crank around to Top dead center on the # 1 cylinder,. It will read Zero degrees on the timing mark scale.
Up top, look at the cam gear closely You will see that there are 5 spokes which support the actual gear. Look closer and you will see that one of these spokes has a small hole in it about 3/4th of the way towards the outside of the gear. Position the gear to where that hole is at 12:00 PM. NOW, if you look thorough the hole, you should should see a small notch that the hole should be centered on. If not, move the gear until you can look through the hole and the notch falls dead center. At that point in time, you have the crank ant camshaft in perfect time with each other.
When you put the belt on, make sure that the side which is slack is the tensioner side. You should be able to slip the belt on, matching the teeth with the teeth on the gears to where one side is fairly tight and you can not roll the cam counter clockwise.
IF you are replacing the belt, you have the crank pulley off and you position the woodruff key straight up at 12:00 PM and the procedures are all the same other than that. when you set the tension. A good rule of thumb is to find the longest span of belt, and with your thumb and forefinger twist the belt. if it twists to 45 degrees toward the block, it's perfect. Any more or less, needs to be reset.
I hope my answer suffices. A picture wouldn't be any more clear.
Let me know how you did.
NOTE: This engine does NOT bend valves when a timing belt fails.
Posted on May 06, 2009
Click on the following free direct Link. It has the Timing: Belt and Crakshaft and Camshaft Mark Diagrams for your 1990 Toyota Camry 2.0L. Plus additional Instructional and Directional Diagrams.
Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!
Posted on Mar 30, 2010
check w/your dealer to find out if the arrows on your timing sprockets both go down go up or point at each other your crank has a keeper pin so you can only put the sprocket (gear) on one way. arrows facing out so you can see them.
Posted on Sep 08, 2010
Tips for a great answer:
May 02, 2017 | 1994 Toyota Tercel
Nov 18, 2014 | Toyota Cars & Trucks
Jan 18, 2014 | 2000 Toyota Corolla
Dec 20, 2012 | 1986 Toyota Tercel
Nov 01, 2011 | Cars & Trucks
Mar 22, 2010 | 1994 Toyota Camry
Feb 28, 2010 | 1986 Toyota Tercel
Sep 20, 2009 | 1991 Toyota Camry
Jul 28, 2008 | 1987 Toyota Tercel Liftback
143 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: