Question about Cars & Trucks

Open Question

Code 82 on the dash Holdern Barina spark, only 6000km and serviced at 6 months. What does the code mean ,

Only just came up

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you turn off code 82 on a Chevrolet Spark?


Code 82 comes on when the oil life falls below 5%. It will turn on everytime you turn the car on, you can exit the code 82 by pressing menu. Don't reset the oil life until you actually change it. .

Jan 07, 2016 | Chevrolet Cars & Trucks

1 Answer

Holden barina code


Time for a service and reset for next service

Aug 16, 2014 | Cars & Trucks

1 Answer

Why do the dash lights go out when driving?


check the dash dimmer switch first.there is 12v in and and a variable voltage out.

Jul 06, 2014 | 1992 Holden Barina

1 Answer

Chevy spark 2013 service code 82


Code 82, means time to change your oil. When you get your oil change, and they reset your indicator

Jun 02, 2014 | 2013 Chevrolet Spark

1 Answer

2008 jeep code p2302 mean


do you want me to guess?
or do you want DIY testing advice.
mean, it means bad spark, from Ign.coil 1, (2 cyl wasted spark)

DIY , actual tests... per FSM. get one.
only 1 code. and comes back after clearing it?
full scan done?
how many miles on it, when was the last full tune up
page 412 opr, guide in glove box , did you do the 102k mile service?
new spark plugs and 6v wire sets? , now be the the time
not a new coil pack that be last choice.

p2 means factory code, and seems your scan tool works right.
many dont. or are blind to them or get them all wrong.

same car as my main car... JK,
i have the full JK, FSM. factory service manual, go it day 2.
the first thing to do, when doing DIY , is to open the hood
and see what engine you have, as diff, engines have diffr, EFI systems.
mine has the Trenton 3.8L V6. with MAP and TBW system.
TBW is throttle by wire. (map sensor is for speed density system)

P2302
P= powertrain
2= jeep private code, not USA fed, spec EPA codes.
3= Fuel and Air Metering (Injector Circuit)
02= Ignition Coil 1 Secondary Circuit- Insufficient Ionization

02= Ignition Coil 1 Secondary Circuit- Insufficient Ionization

this car has a coil pack and is WASTED SPARK
3 coils 6 spark plugs. wasted. (google what that means)
but is important to know because either spark plug can disturb
the current path here.

if my 6v did this, id do the 102k mile service. with NGK parts,.
or Bosch.

we , usually you get P03xx codes with it. misfire.

i open my fsm ,there are 6 tests. for this 1 failure
it says the spark duration is too short or nothing at all.
ill not type out all 6 tests nor the logic, (alldata.com has it)
step 1 is to :
clear all DTC
and key on (no start)
scan it, do you get 2302? now, not running,
that is correct the ecu test coil primary , before running, amazing,
if yes, the next steps are to see if the coil is bad (open primary)
or the ASD drive is dead.




Jan 19, 2014 | 2008 Jeep Wrangler

1 Answer

Holden Barina Model 2006 engine light comes on & off


Please check the oil pressure transducer , check and replace the oil filter. Also check if there is connection issue of the oil pressure switch. since the ECU has not detected any faults it can be associated with some external problems. Check also the ground to the panel and the cluster connections on the dash.

Nov 14, 2011 | Cars & Trucks

2 Answers

2006 TK Holden Barina Manual 3 Door Hatch - Engine Will Turn Over, But Will Not Start, Plenty Of Fuel & Spark To Plugs


Make sure that you are getting a clean, blue, spark. Not an orange spark. And also it could be off time.

May 17, 2011 | Daewoo Lanos Cars & Trucks

1 Answer

Lights blowing on Barina


running voltage is a little higher than normal... too high if reading while under load..(lights on)..but alternator should be checked /replaced in this scenario as moist likely suspect..good luck

Dec 14, 2008 | 2003 GMC Sierra

1 Answer

Holden barina 2003


it means its due for service. If u wanna get rid of it without servicing the vehicle then as you start the car simultaneously push the ODOMETER reset button on the dash and it will wipe it. This will however just delay the point your car needs servicing.

Jun 04, 2008 | 2003 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

370 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...