Question about 2001 Chrysler LHS

Open Question

Atc code 36

My AC used to work now sumtimes n my compresser works

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6 Answers

SOURCE: 1999 Chrysler 300m ATC Control Communication Failure

i have the same car and it did the same thing when i got it take it to a dealership there are 2 flashes for the bcm body control module that will recalibrate the automatic temp contol and that should fix the problem

Posted on Apr 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Can't change what vents A/C and heat blow out of.


While it's possible there are other problems the repair procedure would be to replace the blend door motor and while doing so confirm that the blend door moves freely without binding up.

Aug 04, 2016 | 1999 Chrysler 300M

1 Answer

2001 chrysler town and country. A\C heat Blowers will not work when controlled my front main pannel. It is a auto temp controlled system. The rear blower will work but no heat when controlled by the rear...


Hi,
This may be similar to what I just fixed on an '00 dodge:
http://www.dodgeintrepid.net/showthread.php?t=89711

Accessing the Integrated Diagnostic System:

Procedure for Automatic Temp Control (ATC) equipped vehicles:

With the engine ON and the vehicle stopped set the temp to 75*F. Next hold down the Floor, Mix and Defrost buttons until the ATC display begins to flash. While the display is flashing, the system will run it's tests and calibrations.

When the display stops flashing, the tests and calibrations are complete.

The ATC display can only display one error code at a time. Any stored codes can be scrolled through by pressing the Panel mode button once for each code. DO NOT press any other button or you will have to start the test over. Note the codes and refer to the list below to determine what system is malfunctioning.

List of Climate Control DTCs:
23: Blend door actuator feedback failure (bad servo)
24: Mode door actuator feedback failure (bad servo)
25: Ambient temp sensor failure
26: ATC In Car thermister failure (ATC only, bad ATC head or ATC head disconnected while battery is connected)
27: ATC in car sensor failure (ATC only)
31: Recirculation door actuator stalled (stuck door or bad servo)
32: Blend door actuator stall failure (stuck door or bad servo)
33: Mode door actuator stall failure (stuck door or bad servo)
34: Engine temperature message not received (ATC only, bad ATC head or bus failure)
35: Evaporator sensor failure
36: ATC control communication failure (bad ATC head or bus failure)
37: Blend door actuator output shorted to battery (bad servo or wiring fault)
38: Blend door actuator output shorted to ground (bad servo or wiring fault)
39: Mode door actuator output shorted to battery (bad servo or wiring fault)
40: Mode door actuator output shorted to ground (bad servo or wiring fault)
41: Recirculation door actuator output shorted to battery (bad servo or wiring fault)
42: Recirculation door actuator output shorted to ground (bad servo or wiring fault)
43: Common door shorted to battery (probable wiring fault, could be a servo that failed in an odd manner)
44: Common door shorted to ground (probable wiring fault, could be a servo that failed in an odd manner)
45: A/C control blend door input open or shorted with respect to ground (MTC only, wiring fault or bad servo)
46: A/C control blend door shorted to battery (MTC only, wiring fault or bad servo)
47: A/C switch failure (MTC only)
48: A/C control mode door input shorted to ground (MTC only, wiring fault or bad servo)
49: A/C control mode door input shorted to battery (MTC only, wiring fault or bad servo)
50: A/C control electric backlite (EBL) switch fails (MTC only)

51: System voltage too low for calibration!!! (check battery cables, battery and alternator!)

Dec 10, 2014 | 2001 Chrysler Town & Country

1 Answer

Ttack and spedometer wont work sumtime and when it doesn't transmission dont shift right


Take it to a tranmission shop to be road test , They don,t charge to do that,

Nov 29, 2012 | Cars & Trucks

1 Answer

Heater on nissan almera


That noise is the heater and AC air temperature control electric blend door motor trying to move a duct door that is sticking due to heat warping. You will need to remove the entire dash assembly and replace the blend door. This door is located between the AC core and the heater core and "blends" the air from each (hot from heater core and cold from AC core) to give the desired air temperature,.

Oct 11, 2012 | 2001 Nissan Almera Tino

2 Answers

My ac froze up and broke my belt is it a way to bypass the ac


yes, you have to get a delete pully and remove the a/c compresser and install the delete pully

Jul 15, 2012 | 2004 Ford Expedition

1 Answer

I have a 1999 chrysler 300m. i run the diagnostic on the automatic temp. controll and get code 36 got that code to clear and now it shows code 23 can anyone tell what this is and who to fix it thanks


Hi,

Chysler HVAC code 23 = Front Mode (Blend) Door - Range too Large.

Possible causes:

- Actuator circuit test faults preset
- Overcurrent faults present
- Mode door or A/C Heater housing components warped, worn, damaged or broken.
- Mode door actuator
- A/C Heater Control (ATC)

Nov 08, 2011 | 1999 Chrysler 300M

1 Answer

I have a 1999 chrysler 300m. i run the diagnostic on the automatic temp. controll and get code 36. can some one tell me what code 36 is and how to fix it.


Hi there,

Code 36 = ATC Head Command Failure (Chrysler's technical term: EEPROM Checksum Error).

Basically, this code indicates the Auto Temp Control (ATC) has malfunctioned.

If this is a stored code (i.e. not active) and your ATC appears to be working ok, then you can disregard this code. However, if this code is active (i.e your ATC is not communicating with your A/C system), then there is no simple fix you can do yourself.

Although some mechanics would suggest replacing the actual A/C Heater Control, I understand your Chrysler service agent may have a way to re-flash your system to correct this code. I recommend you contact your local service agent and discuss a possible reset of your system.




"If this has helped you in any way, please take a moment to rate this solution"

Nov 05, 2011 | 1999 Chrysler 300M

1 Answer

1999 Chrysler 300m ATC Control Communication Failure


i have the same car and it did the same thing when i got it take it to a dealership there are 2 flashes for the bcm body control module that will recalibrate the automatic temp contol and that should fix the problem

Apr 01, 2009 | 1999 Chrysler 300M

1 Answer

The car keeps coming up a code 23 on a 1999 chrysler 300 for the


Code 23= Blend door feedback control


On cars with automatic climate control: To enter diagnostic mode, set the temperature to 75F, press the the off button. Press Floor, Defrost\Floor, Front Defrost simutaneously for 3 seconds until the temperature display begins to flash.
On cars without automatic climate control, set the blower to any speed, turn the temperature control in between warm and cold. Press Floor, Defrost\Floor, and Front Defrost. All codes will flash via the Front Defrost button.
When the test is over all fault codes will be displayed (on cars without automatic climate control, they will be blinked out on the Front Defrost button).
Code Action
23 Blend door feedback control
24 ATC mode door feedback failure
25 Ambient temperture sensor failure
26 ATC in-car sensor
27 Sun sensor failure
31 ATC recirculate door stall failure
32 ATC blend door failure
33 ATC mode door stall failure
34 Engine temperture sense failure
35 Evap temperature sense failure
36 ATC head command failure

Mar 23, 2009 | 1999 Chrysler 300M

3 Answers

Speedometer reads upto 120 mph sitting still with ac on high


yo, i finally figured out the speedo jumping problem. i took my towncar to a shop and they told me it needed a new instrument cluster, they replaced that and still the same problem. they narrowed it down to some bunk diodes or something in the alternator. replaced the alternator at Schumacher Goodyear and the price was 275. had all the speed sensors checked and they were fine as well. also this website is very helpful for do it urselfers.

http://www.lincolnsonline.com/tech/tech.html


Nov 14, 2008 | 1996 Lincoln Town Car

Not finding what you are looking for?
2001 Chrysler LHS Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...